We need to check for existence of the a.out.h header in the source tree,
not the object tree, if we want it to get the right answer with O=.
Signed-off-by: David Woodhouse <david.woodhouse@intel.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
There is a small off-by-one bug in firewire-sbp2. This causes problems
when a device exports multiple LUN Directories. I found it when trying
to talk to a SONY DVD Jukebox.
Signed-off-by: Richard Sharpe <realrichardsharpe@gmail.com>
Acked-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (op. order, changelog)
This patch fixes an oops in several failure paths in key allocation. This
Oops occurs when freeing a key that has not been linked yet, so the
key->sdata is not set.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
clock is already cpu-endian (see le32_to_cpu slightly before), so
le64_to_cpu doesn't make much sense.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a circular locking dependency in the workqueue handling.
The interface work task uses the mac80211 function
ieee80211_iterate_active_interfaces() which grabs the RTNL lock.
However when the interface is brough down, this happens under the RTNL
lock as well, this causes problems because mac80211 will flush the workqueue
during the ifdown event. This causes mac80211 to wait until the driver has
completed all work which can't finish because it is waiting on the RTNL lock.
This is fixed by moving rt2x00 workqueue tasks on a different workqueue,
this workqueue can be flushed when the ieee80211_hw structure is removed
by the driver (when the driver is unloaded) which does not happen under the
RTNL lock.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
sata_uli can't do hardresets reliably and lock up. This went
unnoticed till now as softreset was the default and hardreset was only
used after softreset failed.
Reported by Christian Casteyde in bz#10860.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Christian Casteyde <casteyde.christian@free.fr>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
dev_close() must be called holding the RTNL. Compile-tested only.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
dev_close() must be called holding the RTNL. Compile-tested only.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
s2io has IOMMU overflow checking, but unfortunately it is wrong.
It didn't use the standard macros, which meant that it only worked
on POWER and SPARC because only those define DMA_ERROR_CODE. Convert it to
use the standard macros instead.
I also commented two more bugs in the IOMMU handling. It assumes
that 0 DMA addresses cannot happen, but that's not true in all IOMMU setups.
The information if a buffer has been already mapped needs to be stored
elsewhere.
Didn't fix those because it needs careful checking of the buffer handling
by the maintainers.
Cc: ram.vepa@neterion.com
Cc: santosh.rastapur@neterion.com
Cc: sivakumar.subramani@neterion.com
Cc: sreenivasa.honnur@neterion.com
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When enabling TSO via ethool on e1000, it is possible to set
NETIF_F_TSO6 on hardware that does not support it. Setting TSO via
ethtool now matches the settings used when the hardware is probed.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The E100 device can't work on current kernel (2.6.26-rc6) and will cause
kernel corruption on intel ixdp4xx.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
PCI_DEVICE_CLASS sets .device and .vendor to PCI_ANY_DEV,
which overrides the effect of preceding PCI_DEVICE() and makes
all elements of netxen_pci_tbl[] identical. Introduced in the
commit dcd56fdbae.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fixes a sparse warning in a code block that's hidden under JUMBO_FRAME #ifdef.
Tested-by: Andrew Savchenko <Bircoph@list.ru>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Make jumbo frame support compile again. It was broken by the cleanup series
before the merge because the code is hidden under JUMBO_FRAME #ifdef.
Tested-by: Andrew Savchenko <Bircoph@list.ru>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Taking sizeof the result of sizeof is quite strange and does not seem to be
what is wanted here.
This was fixed using the following semantic patch.
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
expression E;
@@
- sizeof (
sizeof (E)
- )
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
EEH is not recovering in a reasonable amount of time on PPC during
e1000e_down().
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
EEH is not recovering in a reasonable amount of time on PPC during
igb_down().
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
EEh is not recovering in a resonable amount of time on PPC during
ixgbe_down().
Signed-off-by: Paul Larson <pl@us.ibm.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
On Rx FIFO overflow error, the controller consume a buffer descriptor
but currently the driver does not give it back to the controller.
This results unrecoverable 'Buffer List Exhausted' condition. This
patch fix this problem by moving a "fbl_count--" line to proper place.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Call netif_carrier_off() before starting PHY device. This is a
behavior before converting to generic PHY layer.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The documentation for intr_type module parameter of the s2io driver is
not consistent with the code. The comments in drivers/net/s2io.c are
OK, but Documentation/networking/s2io.txt is wrong.
Pointed out by Andrew Hecox.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The saa7134 driver uses a (non-atomic) variable in an attempt to
only allow one opener of the device (how it deals with sending
the fd over unix sockets I don't know).
Unfortunately, the release function first decrements this variable,
and THEN goes on to disable more of the device. This allows for
a race where another opener of the device comes in after the decrement of
the variable, configures the hardware just to then see the hardware
be disabled by the rest of the release function.
This patch makes the release function use the same lock as the open
function to protect the hardware as well as the variable (which now
at least has some locking to protect it).
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Move allocation after first check and fix memory leak.
Noticed-by: Daniel Marjamäki <danielm77@spray.se>
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch ensures that the xc5000 will have firmware loaded as needed if the
part is powered down or reset via gpio from the host. An example of this, in
some cases, could be after the system resumes from standby or hibernate modes.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This decreases scan time in Queens, New York from 28 minutes to 7 minutes,
with the exact same services found.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
VIDIOC_ENUMSTD did not return all the PAL/SECAM/NTSC variants: it just returned
one single PAL/SECAM/NTSC standard without separate entries for the trickier
standards like NTSC-JP.
Changed the code so that it behaves better.
Also simplified the if/switch statements into a common standards lookup table.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix uncorrected block counter and bit error rate to follow DVB API spec:
- Unsupported controls return -ENOSYS.
- UNC must never be set to 0.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If the i2c write fails during initialisation, an oops happens
because state->frontend.dvb is still undefined. Fixed.
Thanks to Sigmund Augdal for reporting this bug,
and to Hartmut Birr for suggesting the fix.
Thanks-to: Sigmund Augdal <sigmund@snap.tv>
Thanks-to: Hartmut Birr <e9hack@gmail.com>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
cx18: Fix S-Video and Compsite input settings for the Yuan MPC718 per user
reports from Yuri Warczynski <Yuri.Warczynski@gmail.com> and
Brian Hope <brian@hopefamily.info> and enable the card entry. The tuner reset
GPIO pin is likely incorrect as the tuner firmware cannot be reloaded without a
reboot. It is likely the audio routing is done via GPIO which is not
implemented yet, as users report audio doesn't work for some inputs.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
cx18: Add I2C slave reset via GPIO upon initialization. One user,
Michael <msd4824@yahoo.com>, has reported this allows his HVR-1600 EEPROM to
be consistently recognized when using (long,) 100 msec delays. The delays in
this commit are nominal (10 & 40 msec) and need testing/tuning on boards with
I2C problems to find the right values.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This is a fix for the case when a digital capture from dvr0 happens first after
modprobe, before access to any cx18 v4l2 device nodes. The initial dvb feed
start has been changed to load the firmware if not already loaded. Also fixed a
use counter to correct dvb feed accounting if starting the transport DMA fails.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix the cx18-cards.c structures for the HVR-1600 to reflect that audio Line In 2
and FM radio audio go to AIN3 and AIN4 of the CS5345 mux respectively. Verified
by physical inspection of an HVR-1600MCE, by listening to FM broadcasts with the
HVR-1600MCE, and by comparing with the card definition for a PVR-150 in ivtv.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Change the cx18-av-core code so that accesses to cx23418 av core that
cause auto-configuration will be adjusted to emulate the auto-configuration
behavior of the cx25843. This fixes the VBI displayed as video at the top of
the frame for NTSC and probably other things.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The automatic Kconfig selection for tuners and frontends should be
conditional, based on !DVB_FE_CUSTOMISE.
This patch corrects the selection for VIDEO_CX18 on
MEDIA_TUNER_MXL5005S and DVB_S5H1409
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If the current modulation and frequency is already set to
the desired parameters, then don't re-tune.
Don't store current frequency until after we've tuned successfully.
Force a re-tune after resume from standby.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
In the umt-010 driver the struct umt_properties sets the number of URBs for
transfer to 20. But in dvb-usb.h MAX_NO_URBS_FOR_DATA_STREAM is set to 10.
Not surprisingly this causes an oops for all devices which use the umt-010
chipset when they are inserted.
fix on Kaffeine channel scan for
Initialize stream count using MAX_NO_URBS_FOR_DATA_STREAM.
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: maximilian attems <max@stro.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Devices can either be class devices or bus devices, not both at the
same time. Soc-camera host devices usually have a platform device as
their parent. Trying to also register them with a class crashes the
kernel, when linked statically. Interestingly, it works when built
as a module. Thanks to Paulius Zaleckas for reporting.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
platform_get_irq() returns a negative value on error, not 0.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Having the thermometer on during channel configuration
could cause tuning instability.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The TDA18271HD/C1 rf_cal map lookup is expected to go out of range outside
of the frequency window 41 MHz - 61.1 MHz. In these cases, the internal
RF tracking filters calibration mechanism is used.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The IF notch bit gets unset when we update the Main Post Div register
value, before we have a chance to write the desired IF notch setting
to the tuner. Move the IF notch configuration to after we update MPD.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
David Woodhouse