This patch adds 3-wire bluetooth coex support for AR9285.
This support can be enabled through btcoex_enable modparam.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds the debug file to the ath9k debugfs, which lets you modify
the debug_mask at runtime, without having to reload the ath9k module.
Signed-off-by: Jeff Hansen <x@jeffhansen.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch combines the legacy and 11n rcstats into one, using the normal
rate table indices instead of two separate indices for each mode. Legacy
rates also get all of the PER and retry information, now, too.
Signed-off-by: Jeff Hansen <x@jeffhansen.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The previous implementation was moving back to NETWORK SLEEP state
immediately after receiving a Beacon frame. This means that we are
unlikely to receive all the buffered broadcast/multicast frames that
would be sent after DTIM Beacon frames. Fix this by parsing the Beacon
frame and remaining awake, if needed, to receive the buffered
broadcast/multicast frames. The last buffered frame will trigger the
move back into NETWORK SLEEP state.
If the last broadcast/multicast frame is not received properly (or if
the AP fails to send it), the next Beacon frame will work as a backup
trigger for returning into NETWORK SLEEP.
A new debug type, PS (debug=0x800 module parameter), is added to make
it easier to debug potential power save issues in the
future. Currently, this is only used for the Beacon frame and buffered
broadcast/multicast receiving.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Clean debug messages to use appropriate levels,
remove useless messages, and trim the number of
debug levels.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver are trying to create an 'ath9k' directory in debugfs for each
device currently. If there are more than one device in the system, the
second try will always fail.
Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
debugfs ath9k/phy#/wiphy can be used to show the current list of
virtual wiphys and to add/remove virtual wiphys. Eventually, this
interface could be replaced with a cfg80211/nl80211 command that is
passed through mac80211.
For example:
# cat /debug/ath9k/phy0/wiphy
primary: phy0
# echo add > /debug/ath9k/phy0/wiphy
# cat /debug/ath9k/phy0/wiphy
primary: phy0
secondary: phy1
# echo del=phy1 > /debug/ath9k/phy0/wiphy
# cat /debug/ath9k/phy0/wiphy
primary: phy0
In addition, following commands can be used to test pausing and
unpausing of the virtual wiphys:
pause=phy1
unpause=phy1
select=phy1
(select pauses and unpauses wiphys automatically based on channel)
schedule=500
(set wiphy scheduling interval in msec; 0 = disable; default value: 500)
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Split the core header files into manageable pieces.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vasanthakumar Thiagarajan