The default values of HARDIRQ_BITS and PREEMPT_BITS in common code leads to
build failure:
In file included from include/linux/interrupt.h:12,
from include/linux/kernel_stat.h:8,
from arch/blackfin/kernel/asm-offsets.c:32:
include/linux/hardirq.h:66:2: error: #error PREEMPT_ACTIVE is too low!
So until that gets resolved, just declare our own default value again.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
On Blackfin SMP, a per-cpu loops_per_jiffy is pointless since both cores
always run at the same CCLK. In addition, the current implementation has
flaws since the main consumer for loops_per_jiffy (asm/delay.h) uses the
global kernel loops_per_jiffy and not the per_cpu one. So punt all of the
per-cpu handling and go back to the global shared one.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The interrupt context save logic incorrectly stored the address of the
IPEND register rather than its value due to a missing dereference. While
we're here, also enable this code for all kernel debugging scenarios and
not just when KGDB is enabled.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This anomaly only applies to the BF527-0.1, not the BF526-0.1, and not any
other revision of the BF527. So make sure we don't go returning 0xffff
for other cases.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Pull the initial preempt_count value into a single
definition site.
Maintainers for: alpha, ia64 and m68k, please have a look,
your arch code is funny.
The header magic is a bit odd, but similar to the KERNEL_DS
one, CPP waits with expanding these macros until the
INIT_THREAD_INFO macro itself is expanded, which is in
arch/*/kernel/init_task.c where we've already included
sched.h so we're good.
Cc: tony.luck@intel.com
Cc: rth@twiddle.net
Cc: geert@linux-m68k.org
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The recent deprecation of dma_sync_{sg,single} ironically broke Blackfin
systems. This is because we don't define dma_sync_sg_for_cpu at all, so
until the DMA asm-generic conversion/cleanup is done after the next
release, simply stub out the dma_sync_sg_for_{cpu,device} functions.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
We don't support the BF535 at all, and the exception 0x2A text specific to
it is pretty verbose and confusing (since the behavior is simply odd), so
punt it to keep the noise down.
Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The BF526-EZBRD changed SDRAM chips between board revisions, so create a
timing table that can accommodate both.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
We defined SDRAM_tRAS to TRAS_4, but then wrongly defined SDRAM_tRAS_num
to 3.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Many aspects of the Blackfin memory map is exactly the same across all
variants. Rather than copy and paste all of these duplicated values in
each header, unify all of these into the common Blackfin memory map header
file. In the process, push down BF561 SMP specific stuff to the BF561
specific header to keep the noise down.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The current cache options don't really represent the hardware features.
They end up setting different aspects of the hardware so that the end
result is to turn on/off the cache. Unfortunately, when we hit cache
problems with the hardware, it's difficult to test different settings to
root cause the problem. The current settings also don't cleanly allow for
different caching behaviors with different regions of memory.
So split the configure options such that they properly reflect the settings
that are applied to the hardware.
Signed-off-by: Jie Zhang <jie.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The kgdb (in multiple places) and traps code developed pretty much
identical checks for how to access different regions of the Blackfin
memory map, but each wasn't 100%, so unify them to avoid duplication,
bitrot, and bugs with edge cases.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Convert most arches to use asm-generic/kmap_types.h.
Move the KM_FENCE_ macro additions into asm-generic/kmap_types.h,
controlled by __WITH_KM_FENCE from each arch's kmap_types.h file.
Would be nice to be able to add custom KM_types per arch, but I don't yet
see a nice, clean way to do that.
Built on x86_64, i386, mips, sparc, alpha(tonyb), powerpc(tonyb), and
68k(tonyb).
Note: avr32 should be able to remove KM_PTE2 (since it's not used) and
then just use the generic kmap_types.h file. Get avr32 maintainer
approval.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: <linux-arch@vger.kernel.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Bryan Wu <cooloney@kernel.org>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: "Luck Tony" <tony.luck@intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Blackfin arch has a bunch of custom section markings for its on-chip
regions, but they aren't declared in the right header.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Looks like the mutex-dec.h header file was incorrectly copied into the
Blackfin asm path. Nothing uses it, so punt it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This converts the irq handling in the Blackfin arch from the old irq.h /
system.h method to the new irqflags.h. A stepping stone on the way to
other tracing functionality.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The IRQ functions take an "unsigned long" flags variable, not any other
type, so fix the places where we use "int" or "long".
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The KGDB code uses this when switching processors to make sure the icache
is in a valid state.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
There is no need for the L1 attribute to be on the prototype of the
access_ok() function as all consumers of the function do not care where it
lives -- they'll always use pcrel calls to get to it. This prevents
pointless recompiles of most of the system when this config option changes.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The common code already has a prototype for this function and we don't use
it anywhere in the Blackfin code, so punt it from the Blackfin headers.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The core string/clear user functions weren't checking the user pointers
which caused kernel crashes with some bad programs and tests (like LTP).
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The latest Blackfin toolchain has fixed its relocation scheme to match
other ports: always use R_BFIN_ prefix and capitalize everything. This
brings the kernel in line with those fixes.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Make sure the internal core buffers are flushed before telling the DMA
engine to fetch the descriptor structure so that it gets the right values.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The Per-processor Data Area isn't actually reserved by this function, and
all it ended up doing was issuing a printk(), so punt it.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
First we fix the prototypes for functions that return boolean values by
using "int" rather than "uint16_t". Then we introduce a get_gptimer_run()
function for checking the current run status of a timer, and then we add a
disable_gptimers_sync() function which parallels disable_gptimers() with
corresponding normal "_sync" behavior.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Hardware errors on the Blackfin architecture are queued by nature of the
hardware design. Things that could generate a hardware level queue up at
the system interface and might not process until much later, at which
point the system would send a notification back to the core.
As such, it is possible for user space code to do something that would
trigger a hardware error, but have it delay long enough for the process
context to switch. So when the hardware error does signal, we mistakenly
evaluate it as a different process or as kernel context and panic (erp!).
This makes it pretty difficult to find the offending context. But wait,
there is good news somewhere.
By forcing a SSYNC in the interrupt entry, we force all pending queues at
the system level to be processed and all hardware errors to be signaled.
Then we check the current interrupt state to see if the hardware error is
now signaled. If so, we re-queue the current interrupt and return thus
allowing the higher priority hardware error interrupt to process properly.
Since we haven't done any other context processing yet, the right context
will be selected and killed. There is still the possibility that the
exact offending instruction will be unknown, but at least we'll have a
much better idea of where to look.
The downside of course is that this causes system-wide syncs at every
interrupt point which results in significant performance degradation.
Since this situation should not occur in any properly configured system
(as hardware errors are triggered by things like bad pointers), make it a
debug configuration option and disable it by default.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
When possible, work around anomaly 05000220 (external memory is write
back cached, but L2 is not cached). If not possible, detect the
conditions at build time and reject any qualifying configurations.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
For systems where the core cycles are not a usable tick source (like SMP
or cycles gets updated), enable gptimer0 as an alternative.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Our early L1 relocate code may implicitly call code which lives in L1
memory. This is due to the dma_memcpy() rewrite that made the DMA code
lockless and safe to be used by multiple processes. If we start the
early DMA memcpy to relocate things into L1 instruction but then our
DMA memcpy code calls a function that lives in L1, things fall apart.
As such, create a small dedicated DMA memcpy routine that we can assume
sanity at boot time.
Reported-by: Filip Van Rillaer <filip.vanrillaer@oneaccess-net.com>
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger