Hi,
This patch relates to mostly performance related changes.
1. Fixed incorrect computation of PANIC level in rx_buffer_level().
2. Removed unnecessary PIOs(read/write of tx_traffic_int and
rx_traffic_int) from interrupt handler and removed read of
general_int_status register from xmit routine.
3. Enable two-buffer mode(for Rx path) automatically for SGI
systems. This improves Rx performance dramatically on
SGI systems.
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Raghavendra Koushik <raghavendra.koushik@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
This patch fixes certain memory leaks discovered in free_tx_buffers()
and rx_osm_handler()
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Raghavendra Koushik <raghavendra.koushik@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
Below patch includes fixes for few purely software bugs identified
since last release.
1. Keep track and display(as part of ethtool command output) the no.
of single-bit and double-bit ECC errors.
2. Handle race condition between intr handler and "interface down"
routine.
3. Initial link state setting modified so that the link state displayed
after "interface Up" is correct.
4. Fix for "Incorrect Tx packet count when TSO is enabled".
5. Disable periodic DMA of statistics and schedule one-shot DMA
only when required.
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Raghavendra Koushik <raghavendra.koushik@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
Below patch addresses few h/w specific issues.
1. Check for additional ownership bit on Rx path before
starting Rx processing.
2. Enable only 4 PCCs(Per Context Controller) for Xframe I
revisions less than 4.
3. Program Rx and Tx round robin registers depending on
no. of rings/FIFOs.
4. Tx continous interrupts is now a loadable parameter.
5. Reset the card if we get double-bit ECC errors.
6. A soft reset of XGXS being done to force a link state change has been
eliminated.
7. After a reset, clear "parity error detected" bit,
PCI-X ECC status register, and PCI_STATUS bit in
tx_pic_int register.
8. The error in the disabling allmulticast implementation has been
rectified.
9. Leave the PCI-X parameters MMRBC, OST etc. at their
BIOS/system defaults.
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Raghavendra Koushik <raghavendra.koushik@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
We are submitting a series of 13 patches to support our Xframe I and
Xframe II line of products. The patches can be categorized as follows:
Patches 1-8 : Changes applicable to both Xframe I and II
Patches 9-11: Xframe II specific features
Patch 12: Addresses issues found during testing cycle.
Patch 13: Incorpoates mostly the review comments from community
and some last moment bug fixes.
Please review the patches and let us know your comments.
Starting with patch 1 below.
This patch involves cosmetic changes(tabs and indentation,
regrouping of transmit and receive data structures, typecasting,
code cleanup).
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Raghavendra Koushik <raghavendra.koushik@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fix the p-persistence CSMA algorithm which in simplex mode was starting
with a slottime delay before doing anything else as if there was carrier
collision resulting in bad performance on simplex links.
Signed-off-by: Ralf Baechle DL5RB <ralf@linux-mips.org>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Else on SMP systems it is possible for hotplug to execute,
invoke tg3_open(), and end up loading the uninitialized
PCI register save area into the card.
Signed-off-by: David S. Miller <davem@davemloft.net>
cs89x0 talks a lot at boot. Seems like debug leftover. This patch
downgrades printks to KERN_DEBUG. While we're at it, make these messages a
bit less obscure.
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make it compile with CONFIG_PM=n
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Drivers really only work well in SMP if they actually can be selected.
This is a leftover from the time when the 6pack drive only used to be
a bitrotten variant of the slip driver.
Signed-off-by: Ralf Baechle DL5RB <ralf@linux-mips.org>
Kconfig | 2 +-
1 files changed, 1 insertion(+), 1 deletion(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Whitespace cleanup for loopback driver. Hopefully it fixes the last few
annoyances.
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch slightly optimizes the loopback driver's stats update.
Saves two loads, one add and one increment per packet sent.
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch #ifdefs the TSO code in the loopback driver.
Saves ~800 bytes of text on i386 and avoids a conditional in the fast path.
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
--ReaqsoxgOBHFXBhH
Content-Type: text/plain; charset=us-ascii
Content-Disposition: inline
Hi Jeff,
Here's a little patch fixing a typo in smc91x.h.
Regards,
Tony
--ReaqsoxgOBHFXBhH
Content-Type: text/x-chdr; charset=us-ascii
Content-Disposition: inline; filename="patch-fix-typo-smc91x.h"
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Use module_param() instead of the old MODULE_PARM()
Signed-off-by: Victor Fusco <victor@cetuc.puc-rio.br>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Yukon-Lite chipset needs workaround for revision 7 (or later).
Without this patch, chip gets stuck in low power mode and never
boots. Newer SysKonnect vendor code already had same patch.
Related bug in skge is http://bugs.gentoo.org/87822
Chris, please add for 2.6.12.2
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Cleanup code that is used to toggle LED's. Since we
get called from ethtool, can use that thread rather than
setting up a timer.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
During autonegotiation set PHY interrupt mask to ignore
bogus speed change interrupts.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The code to clear fifo errors was incorrect and sending garbage
to the external phy. Removed the no longer used inline's funcs.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The check for Yukon lite changes was restricting itself to
rev A3. It turns out that these changes are also true on A4
and later.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Cleanup the phy_lock deadlock because of relocking in the nway_reset path.
Reported by Francois Romieu.
Also, don't need to do irqsave/restore for blink,
just excluding bh is good enough.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Here is a fix for a typo, thanks Eliot Dresselhaus.
Since transmitter not active when device is down, it wasn't really noticed.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The SK-9E boards use the Marvell Yukon2 chipset which
is not supported by the skge driver. Thanks to Ralph Roesler
for noticing.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Using Genesis board, I get harmless error reports. Rather than console
error, turn it into a error counter.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
A few sparse cleanups for orinoco.c
Signed-off-by: Peter Hagervall <hager@cs.umu.se>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch makes tms380tr use the new DMA API. Now that on Alpha, this API
also supports bus master DMA for ISA (platform) devices, i changed the
driver to use this new API.
This also works around a bug in the firmware loader: The example provided
in Documentation/firmware_class no longer works, as the firmware loader now
calls get_kobj_path_length() and the kernel promptly oopses, as the
home-grown device doesn't have a parent. Of course, this doesn't happen
with a "real" device which has its bus (or pseudo bus in the case of
platform) as parent.
Converted tms380tr to use new DMA API:
- proteon.c, skisa.c: use platform pseudo bus to create a struct device
- Space.c: delete init hooks
- abyss.c, tmspci.c: pass struct device to tms380tr.c
- tms380tr.c, tms380tr.h: new DMA API, use real device fo firmware loader
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
In ALB mode, allow new slave to use bond's MAC address if the new
slave's MAC address is being used within the bond and no other slave
is using the bond's MAC address.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
ethernet drivers to remain as ignorant as is reasonable of the connected
PHY's design and operation details.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
An early version of the sk98lin patch was merged via Len's tree. But there
were subsequent updates as a result of review from Jeff. THis fixes things
up.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
sys_reboot() now calls device_suspend(), so it is no longer necessary for
the e1000 driver to register a reboot notifier [in fact doing so results in
e1000_suspend() getting called twice].
(akpm: we need to fast-track this. It's causing ia64 to oops on shutdown)
Signed-off-by: Tony Luck <tony.luck@intel.com>
Cc: <cramerj@intel.com>
Cc: <john.ronciak@intel.com>
Cc: <ganesh.venkatesan@intel.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If the product-id-string contains the '+' , '&' ,'_', it was not converted
properly from the /etc/pcmcia/config(pcmcia-cs config file).
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove duplicates from the device id table.
Signed-off-by: Jarkko Raja <jar@pcuf.fi>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
`gcc -W' likes to complain if the static keyword is not at the beginning of
the declaration. This patch fixes all remaining occurrences of "inline
static" up with "static inline" in the entire kernel tree (140 occurrences in
47 files).
While making this change I came across a few lines with trailing whitespace
that I also fixed up, I have also added or removed a blank line or two here
and there, but there are no functional changes in the patch.
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
turn many #if $undefined_string into #ifdef $undefined_string to fix some
warnings after -Wno-def was added to global CFLAGS
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move in_aton to allow netpoll and pktgen to work without the rest of
the IPv4 stack. Fix whitespace and add comment for the odd placement.
Delete now-empty net/ipv4/utils.c
Re-enable netpoll/netconsole without CONFIG_INET
Signed-off-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Suggestion from Sam Ravnborg <sam@ravnborg.org>
It causes all driver families to be displayed aligned immediately under the
main network drivers heading (in menuconfig/xconfig/gconfig) instead of
not being subordinate to (i.e., not indented) the Network device support
heading at all.
The improved network driver families are:
token ring, wireless, PCMCIA, WAN, ATM, and S390.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add 5780S support by adding a new tg3_setup_fiber_mii_phy() function and
a timer function for parallel link detection. 5780S uses standard MII
registers for 1000BaseX and runs in GMII mode as opposed to TBI mode on
older serdes chips.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
raghavendra.koushik@neterion.com