Multi-protocol adapters support different port types. Each consumer
of mlx4_core queries for supported port types; in particular mlx4_ib
can no longer assume that all physical ports belong to it. Port type
is configured through a sysfs interface. When the type of a port is
changed, all mlx4 interfaces are unregistered, and then registered
again with the new port types.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add support for managing MAC and VLAN filters for each port.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Oren Duer <oren@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Get maximum ethernet MTU and default MAC address from the firmware
QUERY_DEV_CAP command.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
For ethernet support, we need to reserve QPs for the ethernet and
fibre channel driver. The QPs are reserved at the end of the QP
table. (This way we assure that they are aligned to their size)
We need to consider these reserved ranges in bitmap creation, so we
extend the mlx4 bitmap utility functions to allow reserved ranges at
both the bottom and the top of the range.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
To allow allocating an aligned range of consecutive QP numbers, add an
interface to reserve an aligned range of QP numbers and have the QP
allocation function always take a QP number.
This will be used for RSS support in the mlx4_en Ethernet driver and
also potentially by IPoIB RSS support.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Byte swap the addresses in the page list for fast register work requests
to big endian to match what the HCA expectx. Also, the addresses must
have the "present" bit set so that the HCA knows it can access them.
Otherwise the HCA will fault the first time it accesses the memory
region.
Signed-off-by: Vladimir Sokolovsky <vlad@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add ethernet-related fields to struct mlx4_cqe so that the mlx4_en
ethernet NIC driver can share the same definition.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add fields for VLAN tag and insert VLAN tag flag to the control
section struct. These fields will be used for sending ethernet
packets.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add support for the following operations to mlx4 when device firmware
supports them:
- Send with invalidate and local invalidate send queue work requests;
- Allocate/free fast register MRs;
- Allocate/free fast register MR page lists;
- Fast register MR send queue work requests;
- Local DMA L_Key.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add support for handling the IB_QP_CREATE_MULTICAST_BLOCK_LOOPBACK
flag by using the per-multicast group loopback blocking feature of
mlx4 hardware.
Signed-off-by: Ron Livne <ronli@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Extend the mlx4_cq_resize() API with a way to set the "collapsed" flag
for the CQ being created.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Avoid duplicating code in ethernet and FC modules.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Wrap doorbell, buffer and MTT allocation in helper functions for
ethernet and FC modules to use.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In addition to mlx4_ib, there will be ethernet and FC consumers of
mlx4_core, so move the code for managing kernel doorbells into the
core module to avoid having to duplicate this multiple times.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ConnectX devices support checksum generation and verification of TCP
and UDP packets for UD IPoIB messages. This patch checks if the HCA
supports this and sets the IB_DEVICE_UD_IP_CSUM capability flag if it
does. It implements support for handling the IB_SEND_IP_CSUM send
flag and setting the csum_ok field in receive work completions.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Ali Ayub <ali@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The struct mlx4_interface.event() method was supposed to get an enum
mlx4_dev_event, but the driver code was actually passing in the
hardware enum mlx4_event values. Fix up the callers of
mlx4_dispatch_event() so that they pass in the right type of value,
and fix up the event method in mlx4_ib so that it can handle the enum
mlx4_dev_event values.
This eliminates the need for the subtype parameter to the event
method, so remove it.
This also fixes the sparse warning
drivers/net/mlx4/intf.c:127:48: warning: mixing different enum types
drivers/net/mlx4/intf.c:127:48: int enum mlx4_event versus
drivers/net/mlx4/intf.c:127:48: int enum mlx4_dev_event
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ConnectX HCA supports shrinking WQEs, so that a single work request
can be made of multiple units of wqe_shift. This way, WRs can differ
in size, and do not have to be a power of 2 in size, saving memory and
speeding up send WR posting. Unfortunately, if we do this then the
wqe_index field in CQEs can't be used to look up the WR ID anymore, so
our implementation does this only if selective signaling is off.
Further, on 32-bit platforms, we can't use vmap() to make the QP
buffer virtually contigious. Thus we have to use constant-sized WRs to
make sure a WR is always fully within a single page-sized chunk.
Finally, we use WRs with the NOP opcode to avoid wrapping around the
queue buffer in the middle of posting a WR, and we set the
NoErrorCompletion bit to avoid getting completions with error for NOP
WRs. However, NEC is only supported starting with firmware 2.2.232,
so we use constant-sized WRs for older firmware. And, since MLX QPs
only support SEND, we use constant-sized WRs in this case.
When stamping during NOP posting, do stamping following setting of the
NOP WQE valid bit.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Now that struct mlx4_buf.u is a struct instead of a union because of
the vmap() changes, there's no point in having a struct at all. So
move .direct and .page_list directly into struct mlx4_buf and get rid
of a bunch of unnecessary ".u"s.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Since kernel virtual memory is not a problem on 64-bit systems, there
is no reason to use our own 2-layer page mapping scheme for large
kernel queue buffers on such systems. Instead, map the page list to a
single virtually contiguous buffer with vmap(), so that can we access
buffer memory via direct indexing.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We use struct mlx4_buf for kernel QP, CQ and SRQ buffers, and the code
to look up an entry is duplicated in get_cqe_from_buf() and the QP and
SRQ versions of get_wqe(). Factor this out into mlx4_buf_offset().
This will also make it easier to switch over to using vmap() for buffers.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Implement FMRs for mlx4. This is an adaptation of code from mthca.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
display the following device information under /sys/class/infiniband/mlx4_X:
board_id, fw_ver, hw_rev, hca_type.
This patch makes this information available to userspace utilities
such as ibstat and ibv_devinfo.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Get the maximum message size from the device capabilities returned
from the QUERY_DEV_CAP firmware command, rather than hard-coding 2 GB.
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Inline data segments in send WQEs are not allowed to cross a 64 byte
boundary. We use inline data segments to hold the UD headers for MLX
QPs (QP0 and QP1). A send with GRH on QP1 will have a UD header that
is too big to fit in a single inline data segment without crossing a
64 byte boundary, so split the header into two inline data segments.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Upcoming firmware introduces command interface revision 3, which
changes the way port capabilities are queried and set. Update the
driver to handle both the new and old command interfaces by adding a
new MLX4_FLAG_OLD_PORT_CMDS that it is set after querying the firmware
interface revision and then using the correct interface based on the
setting of the flag.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add an InfiniBand driver for Mellanox ConnectX adapters. Because
these adapters can also be used as ethernet NICs and Fibre Channel
HBAs, the driver is split into two modules:
mlx4_core: Handles low-level things like device initialization and
processing firmware commands. Also controls resource allocation
so that the InfiniBand, ethernet and FC functions can share a
device without stepping on each other.
mlx4_ib: Handles InfiniBand-specific things; plugs into the
InfiniBand midlayer.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Yevgeny Petrilin