The purpose of this patch is to split off the case when a device does
not reply on the lower level (which is reported by HC hardware), and
a case when the device accepted the request, but does not reply at
upper level. This redefinition allows to diagnose issues easier,
without asking the user if the -110 happened "immediately".
The usbmon splits such cases already thanks to its timestamp, but
it's not always available.
I adjusted all drivers which I found affected (by searching for "urb").
Out of tree drivers may suffer a little bit, but I do not expect much
breakage. At worst they may print a few messages.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
While converting the configuration for the old DiB3000MC-module to the new one
a wrong AGC configuration was introduced.
This is using the old one again.
Signed-off-by: Jose Alberto Reguero <jareguero@telefonica.net>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There seems to be an off by one error in the dibusb-mb.c which causes
the "Artec T1 with AN2235" box to be detected as a totally different
box - but it only happens if the Artec is one with the correct USB
IDs. A patch is attached to the second post. However, even with this
patch, the box still won't tune. It will tune using a 2.6.12 kernel
though.
Signed-off-by: Alistair Buxton <a.j.buxton@gmail.com>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Attached is a patch against latest HG which adds remote control support
to the DigiTV driver. It works for me;
Signed-off-by: Allan Third <allan.third@gmail.com>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch fixes the physical address and takes into account recent
changes in the USB input subsystem.
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Unai Uribarri <unaiur@gmail.com>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
After some structural changes, here comes the updated patch for the Club 3D
zap250mini USB dvb device.
Adding support for a WideView-based device with a different "COLD" ID.
Signed-off-by: Jochen Issing <jochen.issing@isign-softart.de>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Force parallel transport stream output on the ZL10353 attached to a
bluebird device.
Addresses the problem where a frontend lock was observed, but no MPEG
transport data was received.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Another stupid fix for attaching the DiB3000MC. == 0 instead of != 0.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
DiB3000MC: set FE to NULL after being freed
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
A new revision of the Avermedia A800 does not reenumerate after download the firmware.
Signed-off-by: Klaus Frahm <frahm@irsamc.ups-tlse.fr>
Signed-off-by: Martin Habbecke <M.Habbecke@gmx.de>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Thomas Rokamp and others are reporting:
"I have now with success extracted a working firmware for the 93004 rev. C1A2."
This patch increments the firmware version to 2.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Flynn Marquardt found out that there is problem with the new dib3000mc-driver
when using with the real dib3000mc. It resulted in a segfault.
Fixed two things: use the correct I2C address and do not attach a tuner, when
the demod was previously failing.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
A complete rewrite of the DiB3000MC/P driver has been done. It is now much more
easy to maintain and to get improvements inside.
Additionally the tuning time has been reduced and the usage of the driver is
much more understandable now.
Signed-off-by: Patrick Boettcher <pboettcher@dibcom.fr>
Signed-off-by: Francois KANOUNNIKOFF <fkanounnikoff@dibcom.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
new tuner api
minor fixes for tuning
Signed-off-by: Olivier DANET <odanet@caramail.com>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Some minor code cleanups and added the MT2060 to new v4l-dvb-build-system, preliminarily under dvb/frontends.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
+ Added support for the remote control shipped with the pen drive size
DVB-T receiver
[ID 10b8:0bc7 DiBcom DiBcom USB2.0 DVB-T reference design (MOD3000P)]
Signed-off-by: Sergei Haller <sergei@sergei-haller.de>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- AGC gain set to 3
- The tuning sequence has been changed to match the DibCom driver ( from I2C
spy captures )
- For LITE-ON adapters : The IF1 frequency is now tuned according to the
calibration values stored in EEPROM.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Olivier DANET <odanet@caramail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Adding the USB ids for the LeadTek clone of the STK3000P-ref-design.
Signed-off-by: Olivier DANET <odanet@caramail.com>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Adding the USB IDs to dibusb-mc.c for the Artec T14 USB Stick based on STK3000P reference design.
Thanks to Thomas Rabe testing.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- some coding style fixes for newly added mt2060
- moved agc-config from fixed values in dib3000mc to configurable ones
- whitespace clean-ups for usb-id-file
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- MT2060 tuner driver
- Added support for some USB DVB-T devices based on Dib3000P
Signed-off-by: Olivier DANET <odanet@caramail.com>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Allow it to be en/disabled
Disable it in < 2.6.17 due to symbol_xxx() bug
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Acked-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Only devices using > 1 frontend were ported; ones which did not are left
using static binding.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Acked-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Ok, here is the working patch for the Freecom DVB-T stick with USB-ID
14aa:0225.
It uses the Firmware-file, wich Erich Focht created and wich can be obtainded
from http://home.arcor.de/efocht/dvb-usb-wt220u-fc03.fw
Also the original patch is from Erich. It adds the proper USB-IDs and I only
had to change the endpoint of the MPEG-2 data-transfer to 0x86.
Signed-off-by: Alexander Tuschen <atuschen@web.de>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Several DVB modules depends on I2C
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds support for a newer version of this device
using the zl10353 frontend instead of the mt352 frontend.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The dvb_frontend_ops is a pointer inside dvb_frontend. That's why every demod-driver
is having a field of dvb_frontend_ops in its private-state-struct and
using the reference for filling the pointer-field in dvb_frontend.
- It saves at least two lines of code per demod-driver,
- reduces object size (one less dereference per frontend_ops-access),
- be coherent with dvb_tuner_ops,
- makes it a little bit easier for newbies to understand how it works and
- avoids stupid mistakes because you would have to copy the dvb_frontend_ops
always, before you could assign the static pointer directly, which was
dangerous.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Some of the dvb_tuner_ops-pointer were set before having a dvb_frontend creating.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Minor code cleanup on the genpix-module.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This is a patch which includes support for the GENPIX 8PSK->USB module. The
board supports QPSK, BPSK and 8PSK decoding (though I don't think it will be
DVB-S2 compliant) With the following patch, the boad is equivalent to a budget
card (no CA Module)
The patch which adds 8psk suppot will follow, but is seperate, as it requires
DVB-S2 support
More info on the board can be found at www.genpix-electronics.com (and they
host the requisite firmwares there as well)
Signed off by: Alan Nisota <alannisota@gmail.com>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Some code had pointless gotos that just didn't make any sense. They didn't
make the code smaller, or faster, or easier to understand.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The calls to set the pll ops were in the wrong place - moved them.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Johannes Stezenbach suggested this change - definite improvement.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
I had forgotten to rename some of the tuner functions in the refactoring.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Rename pll calls to appropriate tuner calls.
Remove pll functions from demod structures.
Hook tuner call into tuner_ops.
Add pll gate control calls where appropriate.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Rename pll calls to appropriate tuner calls.
Add pll gate control calls where appropriate.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- make the following needlessly global struct static:
dvb-usb/cxusb.c: cxusb_mt352_config
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This changeset removes pll_init, and instead sets the tuner
auxiliary byte in pll_set.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Currently in /sys/class/dvb/dvbX.demuxY/ we have:
dev
uevent
With the patch, we have (for a PCI DVB device):
dev
device -> ../../../devices/pci0000:00/0000:00:1e.0/0000:03:0d.0
uevent
So userspace tools can (finally) work out which physical device a DVB adapter
refers to. Previously you had to kinda look through dmesg and hope that it
hadn't been dumped out of the buffer. This makes debugging a lot easier if
the system has been up for a long time!
This is done by adding an extra 'struct device *' parameter to
dvb_register_adapter(). It will work with any kind of standard
linux 'device'. Additionally, if someone has an embedded system which does
things differently, they can simply supply 'NULL' and the behaviour will be
as before - the link will simply not appear.
Ack'd-by: Manu Abraham <manu@linuxtv.org>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch prevents a bug where the frontend is unable to tune after waking
from powered down state. Now, the device remains powered on until it is
disconnected, just like the windows driver. It seems that the bluebird
firmware is unable to successfully handle tuning after a powered down state.
This patch fixes all of the FusionHDTV Bluebird USB2 devices. The Medion
MD95700 will still behave as before, since it was unaffected by this bug.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There seems to be a new version of the USB DVB-T stick from WideView with a new demod-revision inside and thus a new firwmare.
This patch enables support for that.
Thanks to Mikel Martin for early testing.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Pete Zaitcev