This patch fixes 2 issues in RFKILL:
* Calling wiphy_rfkill_stop_polling() in ath9k_stop
would mean that the driver cannot report HW status
when the radio is re-enabled. Move this to ath_detach().
* Calling ath_radio_{enable/disable} without checking the current
state results in ath_radio_enable() being called repeatedly
for every invocation of rfkill_poll(). This is not needed
in any case since wiphy_rfkill_set_hw_state() would call
->stop() if the radio has been disabled.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Autosleep needs to be disabled for AR9287 chipsets also.
Since autosleep is not used for any of the currently supported
chipsets, disable it by default and can be enabled if needed
for any of the future chipsets.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k: Fix bugs in programming registers during PA CAL"
removed a REG_READ of 0x7834. This resulted in incorrect
computation of the subsequent value to be written in RF2G6.
This patch fixes the regression by re-adding the REG_READ.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* This patch fixes a bug in calculating the scaled
power for three chain chipsets.
* Also, a delay is needed after setting DAC low-power mode in
TOP1 RF register (Top Level Register Bits).
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k: Do an AHB reset before doing RTC reset"
fixed RTC reset issue for AR9280 2.0 chipsets and above.
The fix is valid for all AR9280 chipsets.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is needed to account for the number of chains in use,
not just the number of chains present.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9280 requires a full reset during channel change and HW reset.
Currently, a fast channel change is done. This patch fixes
this bug.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
NF value may be incorrect when we read it just after the chip
has gone through a full sleep mode. Reading incorrect NF values
affects RX throughput.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Setting bit 20 and 25 of 0x8344 can cause occasional rx data
corruption, clear them to fix this issue.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Waking up the chip after powering it down fails sometimes.
In this case the CPU is locked for 200ms. Reduce this
interval to 10ms to avoid excessive busy looping.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For chips requiring RTC reset, TSF has to be restored
after power on reset.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Disable L1 state ONLY when device is in D3 mode.
* Clear bit 22 of register 0x4004.
* Handle power on/off properly
Not setting the workarounds properly resulted in the
disappearance of the card in certain cases.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The default noise floor was never initialized for
AR9287.This patch helps in reporting the correct
RSSI for this version of chipset.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When processing MIB interrupts, OFDM and CCK error
handling routines for low RSSI values have to be invoked
only when the channel mode is 11G/11B. Since HT channels
will also fall under the bands 2Ghz/5Ghz, check appropriately.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When processing MIB interrupts, OFDM and CCK error
handling routines for low RSSI values have to be invoked
only when the channel mode is 11G/11B. Since HT channels
will also fall under the bands 2Ghz/5Ghz, check appropriately.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Oops, a stupid mistake in the original patch which adds coex 3-wire
support. Bluetooth priority gpio needs to be gpio 7.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This subsystem id will be used later to turn on the btcoex
support.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CHANNEL_G has to be set for 2GHZ channels since
IS_CHAN_G() checks for this in channelFlags and not in
chanmode. To make things messier, ath9k_hw_process_ini()
checks for CHANNEL_G in chanmode and not in channelFlags.
The supreme, brain-searing fix is to set the
flag in both cases.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
BAR frames have to be sent to mac80211 only if the
current channel is HT. Also, move the macro to
enum ath9k_rx_filter.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k ahb requests an IRQ and indicates 'ath9k' claimed it,
ath9k pci requests an IRQ and indicates 'ath' claims it;
since 'ath' is another module sync both ahb and pci to claim
the irq using 'ath9k'.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We've cleaned up ath_init_device() and its children enough
to pass meaninful errors back from probe. When this fails
it means our device could not be initialized and a meaninful
error will have been passed.
Do the same for request_irq() and also synchronize the error
messages while at it.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The -ENOMEM was never being passed on failure.
While at it use dev_err() as ahb does upon failure.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As generic hw timer interrupt handler is moved to tasklet,
we no more need to call spin_lock_irqsave().
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no point handling this in hard irq, move it to
tasklet.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Doing an RTC reset when DMA is active may corrupt memory,
make sure no DMA is active at this moment by doing an
AHB reset.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds 3-wire bluetooth coex support for AR9285.
This support can be enabled through btcoex_enable modparam.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We don't need a hw cap bit for btcoex anymore as btcoex scheme type
is enough to do this.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also define macros for wlanactive and btactive (5 & 6) gpios.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make sure btcoex register configured with appropriate values
after it is initialized with the default values from initvals.h
during reset.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This function currently does initialization + enable the
btcoex support. Split it into two logical functions which
does the above operations separately. Btcoex initialization
is done during attach time and enabling this feature is done
in start(). Also, add code to disable btcoex support in stop().
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When dumping register contents, HW has to be awake.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
PA Calibration is not needed for high power solutions.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* First PA driver (PDPADRV1) was not powered down properly.
* Compensation capacitor for dynamic PA was programmed incorrectly.
Also, remove a stray REG_READ.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
PA calibration need not be done if the offset is not varying.
The current logic does PA calibration even if the offset is the
same.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Prevent a read of powInfo[-1] in the first iteration.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TX/RX chainmasks were set to 1x1 during scanning.
Configure them properly with the values retrieved from
the EEPROM.
Also, this requires scan_start/scan_end callbacks to be
locked with sc->mutex.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Support for FIF_OTHER_BSS was missing. This patch adds support for this
filtering mode which in turn resolves a problem where mesh interfaces would not
receive broadcast traffic.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Other than ns_avgbrssi (Average beacon rssi) no data of
ath9k_node_stats is being used anywhere. Nuke this structure
and move its only useful member to ar5416Anistate. Also cleanup
this redundant data in ath_softc.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently the beacon rssi that LPF gives is divided and rounded
up by ATH_RSSI_EP_MULTIPLIER twice. This will leave the incorrect rssi
in ANI. Having correct rssi in ANI fixes the connection stability at
< 30dB rssi range. This patch removes the unncessary computation of average
rssi over already valid average rssi. Also removes the redundant macros to
find average rssi.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This moves the shared regulatory structure into the
common structure. We will use this ongoing for common
data.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vivek Natarajan