Export ata_eh_analyze_ncq_error() for subsequent use by sata_mv,
as suggested by Tejun.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Separate out the inner loop body of mv_host_intr()
into it's own function called mv_port_intr().
This should help maintainabilty.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Remove the unwanted reads of hc_irq_cause from mv_host_intr(),
thereby removing a bug whereby we were not always reading it when needed..
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Sigh. Undo some earlier changes to mv_port_intr(),
so that we now read/clear SError again in all cases.
Arrange the top of the function to be as close as possible
to what we need for a later update (in this series) for ERR_DEV handling.
Fix things so that libata-eh can attempt a READ_LOG_EXT_10H
in response to a failed NCQ command, by just doing a local
mv_eh_freeze() rather than ata_port_freeze().
This will now fully handle NCQ errors much of the time,
but more fixes are needed for FBS/PMP, and for certain chip errata.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Rearrange mv_config_fbs() to more closely follow the (corrected) datasheet
recommendations for NCQ and FIS-based switching (FBS).
Also, maintain a port flag to let us know when FBS is enabled.
We will make more use of that flag later in this patch series.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Part 1 of workaround for errata "sata#25" for the 60x1 series
(the second half of this errata workaround is still in development.
Bit22 of the GPIO port has to be set "on" when in NCQ mode.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The EDMA engine cannot tolerate a mix of NCQ/non-NCQ commands,
and cannot be used for PIO at all. So we need to prevent libata
from trying to feed us such mixtures.
Introduce mv_qc_defer() for this purpose, and use it for all chip versions.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When performing EH, it is recommended to wait for the EDMA engine
to empty out requests-in-progress before disabling EDMA.
Introduce code to poll the EDMA_STATUS register for idle/empty bits
before disabling EDMA. For non-EH operation, this will normally exit
without delay, other than the register read.
A later series of patches may focus on eliminating this and various
other register reads (when possible) throughout the driver,
but for now we're focussing on solid reliablity.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some of the GenIIe EDMA optimizations should not be used
for non-PCI (SOC) devices, and nor for certain configurations
of conventional PCI (non PCI-X, PCIe) buses.
Logic taken/simplified from that in the Marvell proprietary driver.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
More cosmetic changes; no code changes.
-- try and improve consistency of naming.
-- add missing _OFS to tails of register offset definitions.
-- rename mv_setup_ifctl() to mv_setup_ifcfg(), since that's what it really does.
-- remove/move some dead comments
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
On certain configurations (certain macbooks), even though all the
conditions for SIDPR access described in the datasheet are met,
actually reading those registers just returns 0 and have no effect on
write. Verify SIDPR is actually working before enabling it.
This is reported by Ryan Roth in bz#10512.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Ryan Roth <ryan.roth@ch2m.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some controllers (jmb and inic162x) use 0x77 and 0x7f to indicate that
the device isn't ready yet. It looks like they use 0xff if device
presence is detected but connection isn't established. 0x77 or 0x7f
after connection is established and use the value from signature FIS
after receiving it.
This patch implements ata_check_ready(), which takes TF status value
and determines whether the port is ready or not considering the above
and other conditions, and use it in @check_ready() functions. This is
safe as both 0x77 and 0x7f aren't valid ready status value even though
they have BSY bit cleared.
This fixes hot plug detection failures which can be triggered with
certain drives if they aren't already spun up when the data connector
is hot plugged.
Tested on sil, sil24, ahci (jmb/ich), piix and inic162x combined with
eight drives from all major vendors.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The discrete VIA ATA chips don't have 0x40 enable bits. We check that
properly in one location but not another. This causes some users 6410
RAID cards to be incorrectly skipped.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use correct variable, achieve desired result...
Spotted by LKML/linux-ide poster whose name I lost (apologies!)
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Tidy up naming of things associated with the PCI / SOC chip
"main irq cause/mask" registers, as inspired by Jeff.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Buffer length handling in simulated commands is error-prone and full
of bugs. There are a number of places where necessary length checks
are missing and if the output buffer is passed in as sglist, nothing
works.
This patch adds a static buffer ata_scsi_rbuf which is sufficiently
large to handle the larges output from simulated commands (4k
currently), let all simulte functions write to the buffer and removes
all length checks as we know that there always is enough buffer space.
Copying in (for ATAPI inquiry fix up) and out are handled by
sg_copy_to/from_buffer() behind ata_scsi_rbuf_get/put() interface
which handles sglist properly.
This patch is inspired from buffer length check fix patch from Petr
Vandrovec.
Updated to use sg_copy_to/from_buffer() as suggested by FUJITA
Tomonori.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Petr Vandrovec <petr@vmware.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* make ata_scsiop_*() static
* make ata_scsi_set_sense() static and move it above its users
* make ata_scsi_rbuf_fill() static
* kill unused ata_scsi_badcmd()
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The platform is actually named routerboard 532 so let's call it this. This
patch only rename files, Kconfig and C symbols; no functional changes.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When count reaches 0 the postfix decrement still subtracts (to -1),
so bfin_reset_controller() returns as if the busy flag was cleared
while it was not.
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Acked-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Re-enable hotplug, now that the interrupt/error handling are mostly sane.
Also update the TODO list at the top.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Here it is again, minus the checkpatch.pl complaint:
Rework mv_err_intr() to leave the SError bits as-is,
so that libata-eh has a chance to see/use them.
We originally thought that clearing them here was necessary
before writing back to edma_err_cause (per the Marvell datasheets),
but we will end up reseting the chip regardless in those cases.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Continue fixing the interrupt handling logic.
Get rid of mv_intr_pio(), by using ata_sff_host_intr() for PIO..
Add a mv_unexpected_intr() catch-all for "impossible" scenarios,
where we get an interrupt that shouldn't have happened
(never seen in testing, but just in case..).
Rearrange the logic so that we always process completed
response queue entries before looking for other events,
This avoids having to re-issue commands that had already succeeded.
As part of this, we split out some duplicated functionality
into a new function, mv_get_active_qc().
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Tidy up host controller interrupt handling, by moving the weirdo
bit shifting from mv_interrupt() to mv_host_intr().
This lets us take advantage of the MV_PORT_TO_SHIFT_AND_HARDPORT() macro
from an earlier patch to greatly simplify the port numbering logic.
Also, defer reading the hc_irq_cause (one per hc) until it is
actually proven to be needed. This may save a microsecond or
so per interrupt, on average (a later patchset will further reduce
unnecessary register reads throughout the driver).
Apart from that, we still leave the actual IRQ handling logic alone.
Subsequent patches in this series will address that.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Try and simplify handling of the request/response queues.
Maintain the cached copies of queue indexes in a fully-masked state,
rather than having each use of them have to do the masking.
Split off handling of a single crpb response into a separate function,
to reduce complexity in the main mv_process_crpb_entries() routine.
Ignore the rarely-valid error bits from the crpb status field,
as we already handle that information in mv_err_intr().
For now, preserve the rest of the original logic.
A later patch will deal with fixing that separately.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Introduce the MV_PORT_TO_SHIFT_AND_HARDPORT() macro,
to centralize/simplify various scattered bits of logic
for calculating bit shifts and the like.
Some of the places that do this get it wrong, too,
so consolidating the algorithm at one place will help
keep the code correct.
For now, we use the new macro in mv_eh_{freeze,thaw}.
A subsequent patch will re-use this in the interrupt handlers
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Ignore *all* interrupt coalescing bits on all controllers,
not just some of each.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
More cosmetic cleanups prior to the interrupt/error handling logic changes.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The drive is directly soldered to the controller, so there is no cable at
all. Remove the 40-wire assumption so the drive can operate at max speed.
Before patch:
$ dd if=/dev/sda of=/dev/null bs=2M count=64 iflag=direct
134217728 bytes (134 MB) copied, 5.29612 s, 25.3 MB/s
After patch:
$ dd if=/dev/sda of=/dev/null bs=2M count=64 iflag=direct
134217728 bytes (134 MB) copied, 3.94955 s, 34.0 MB/s
Signed-off-by: Dan McGee <dpmcgee@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix mis-reporting of NCQ errors by ensuring that result_tf->flags
is properly initialized in libata-eh. This allows ata_gen_ata_sense()
to report the failed block number correctly to SCSI after a media error
during NCQ.
This patch may also be a candidate for backporting to earlier kernels.
Without this fix, SCSI will fail I/O on the entire request rather
than just the bad sector. That can be bad for a request that was
merged from many independent read reads from different tasks.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
These #if's are unneeded since they:
- did anyway not handle the CONFIG_ACPI_DOCK_MODULE case correctly and
- this is already handled in include/acpi/acpi_drivers.h and
- it's now correctly handled in kconfig.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
sata_nv hardreset can't classify but was left out while unifying
follow-up SRST request mechanism[1]. This caused detection failures
on those controllers. Fix it.
Reported and bisected by Roland Dreier, Petr Vandrovec and Marc
Dionne. Thanks guys.
[1] 305d2a1ab1
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Roland Dreier <rdreier@cisco.com>
Cc: Petr Vandrovec <vandrove@vc.cvut.cz>
Cc: Marc Dionne <marc.c.dionne@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some chips need AHCI_EN set more than once to actually set it. Try a
few times before giving up and spitting out WARN_ON().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Peer Chen <pchen@nvidia.com>
Cc: Volker Armin Hemmann <volker.armin.hemmann@tu-clausthal.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
WARN_ON()'s in ata_hsm_move() was too liberal and got triggerred when
it shouldn't (e.g. hotplug events at the right moment). As the HSM
only deals with device errors and state machine violations, make it
check only against them.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Mark Lord <liml@rtr.ca>
Cc: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Since 43cc71eed1, the platform modalias
is prefixed with "platform:". Add MODULE_ALIAS() to the hotpluggable
ATA and IDE platform drivers, to re-enable auto loading.
NOTE: both ata/pata_platform.c and ide/legacy/ide_platform.c claim
to provide "the" platform_pata driver, and there's no build-time
mutual exclusion mechanism. This means that configs which enable
both drivers will make some trouble when hotplugging...
[dbrownell@users.sourceforge.net: more drivers, registration fixes]
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Tejun Heo <htejun@gmail.com>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
sis_scr_cfg_read() can't access SError and was incorrectly returning
-1 instead of -EINVAL. This went unnoticed because SError used to be
cleared in @postreset() and it didn't care about how scr_read() failed
but commit ac371987 moved SError clearing into sata_link_resume() and
SCR access failure other than -EINVAL is considered an error condition
and exposes the incorrect return value bug as detection failure. Fix
it.
Also, scsi_scr_cfg_write() was incorrectly returning 0 after it
ignored the request to write to SError. Make it also return -EINVAL.
This was bisected and reported by Patrick McHardy.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Noticed by sparse
drivers/ata/libata-core.c:3380:12: warning: function 'ata_wait_after_reset' with external linkage has definition
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
It's big, but there doesn't seem to be a way to split it up smaller...
Signed-off-by: Tony Jones <tonyj@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
None of these files use any of the functionality promised by
asm/semaphore.h. It's possible that they rely on it dragging in some
unrelated header file, but I can't build all these files, so we'll have
fix any build failures as they come up.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
The kernel now panics reliably on boot if you have a SATAPI device
connected.
The problem was introduced by the libata merge trying to pull out all
the SFF code into a separate module. Unfortunately, if you're a satapi
device you usually need to call atapi_request_sense, which has a bare
invocation of a SFF callback which is NULL on non-SFF HBAs. Fix this by
making the call conditional.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I got below log after a S3 resume in a ASUS A6VC laptop. The system has
only one IDE drive. It appears there is no reason calling _GTF for
disabled drive.
ACPI Error (dsopcode-0483): Attempt to CreateField of length zero [20070126]
ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0.IDE0.RATA] (Node df822a7c), AE_AML_OPERAND_VALUE
ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0.IDE0.CHN1.DRV0._GTF] (Node df822bd0), AE_AML_OPERAND_VALUE
ata2.00: _GTF evaluation failed (AE 0x3006)
ACPI Error (dsopcode-0483): Attempt to CreateField of length zero [20070126]
ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0.IDE0.RATA] (Node df822a7c), AE_AML_OPERAND_VALUE
ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0.IDE0.CHN1.DRV1._GTF] (Node df822b94), AE_AML_OPERAND_VALUE
ata2.01: _GTF evaluation failed (AE 0x3006)
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
sata_mv does not yet fully support hotplug (coming soon, though).
This means that the driver may not find a Silicon Image port-multiplier
when first loaded, because those devices take in exceess of 3 seconds
to sync up the SATA PHY (most devices do this in mere microseconds).
So, as a short-term interim measure, here we insert a 3-second pause
on initial driver load, once per controller board (not once per port!),
to allow the Silicon Image port-multipliers to be detected later.
This will be removed again (soon!) once hotplug is fully implemented/working.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Remove unnecessary edma init code from port_start.
This sequence gets done later on the first I/O to the port.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add basic port-multiplier support to sata_mv.
This works in Command-based-switching mode for Gen-II chipsets,
and in FIS-based-switching mode for Gen-IIe chipsets.
Error handling remains at the primary port level for now
(works okay, but not great). This will get fixed in a subsequent
patch series for IRQ/EH handling fixes. There are also some
known NCQ/PMP errata to be dealt with in the near future,
once we have this basic PMP support in place.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Mark Lord