And fix up the code to always allow MSI on 5714 A2.
Call tg3_find_peer() earlier because we need that information before
we can determine whether we can set TG3_FLAG_SUPPORT_MSI or not.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without the following patch, the kernel does not automatically detect
2GB CompactFlash cards from Transcend.
Signed-off-by: Fabrice Aeschbacher <fabrice.aeschbacher@siemens.com>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Acked-by: Peter Stuge <peter@stuge.se>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
HPT36x chip don't seem to have the channel enable bits, so prevent the IDE core
from checking them...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Michal Kepien <michal.kepien@poczta.onet.pl>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* fix ->speedproc to set the drive speed
* this driver doesn't support SWDMA so use the correct ->swdma_mask
* BUG() if an unsupported mode is passed to ->speedproc
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This driver doesn't support SWDMA so use the correct ->swdma_mask.
While at it:
* no need to call config_chipset_for_pio() in config_chipset_for_dma(),
if DMA is not available config_chipset_for_pio() will be called
by siimage_config_drive_for_dma() and if DMA is available
config_siimage_chipset_for_pio() will be called by siimage_tune_chipset()
* remove needless config_chipset_for_pio() wrapper
* bump driver version
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* limit max PIO mode to PIO4, this driver doesn't support PIO5 and attempt
to setup PIO5 by it821x_tuneproc() could result in incorrect PIO timings
+ incorrect base clock being set for controller in the passthrough mode
* move code limiting max PIO according to the pair device capabilities from
config_it821x_chipset_for_pio() to it821x_tuneproc() so the check is also
applied for mode change requests coming through ->tuneproc and ->speedproc
interfaces
* set device speed in it821x_tuneproc()
* in it821x_tune_chipset() call it821x_tuneproc() also if the controller is
in the smart mode (so the check for pair device max PIO is done)
* rename it821x_tuneproc() to it821x_tune_pio(), then add it821x_tuneproc()
wrapper which does the max PIO mode check; it worked by the pure luck
previously, pio[4] and pio_want[4] arrays were used with index == 255
so random PIO timings and base clock were set for the controller in the
passthrough mode, thankfully PIO timings and base clock were corrected
later by config_it821x_chipset_for_pio() call (but it was not called for
PIO-only devices during resume and for user requested PIO autotuning)
* remove config_it821x_chipset_for_pio() call from config_chipset_for_dma()
as the driver sets ->autotune to 1 and ->tuneproc does the proper job now
* convert the last user of config_it821x_chipset_for_pio() to use
it821x_tuneproc(drive, 255) and remove no longer needed function
While at it:
* fix few comments
* bump driver version
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Teach the driver's tuneproc() method to do PIO auto-runing properly since it
treated 5 instead of 255 as auto-tune request, and also passed the mode limit
of PIO5 to ide_get_best_pio_mode() despite supporting up to PIO4 only.
While at it, also:
- remove the driver's wrong claim about supporting SWDMA modes;
- stop hooking ide_dma_timeout() method as the handler clearly doesn't fit for
the task...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fold the parts of the ide_dma_end() methods identical to __ide_dma_end() into a
mere call to it.
Start using faster versions of the ide_dma_end() and ide_dma_test_irq() methods
for the PCI0646U and newer chips that have the duplicate interrupt status bits
in the I/O mapped MRDMODE register, determing what methods to use at the driver
load time. Do some cleanup/renaming in the "old" ide_dma_test_irq() method too.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix several issues with the driver's procfs output:
- when testing if channel is enabled, the code looks at the "simplex" bits, not
at the real enable bits -- add #define for the primary channel enable bit;
- UltraDMA modes 0, 1, 3 for slave drive reported incorrectly due to using the
master drive's clock cycle resolution bit.
While at it, also perform the following cleanups:
- don't print extra newline before the first controller's dump;
- correct the chipset names (from CMDxxx to PCI-xxx)
- don't read from the registers which aren't used for dump;
- better align the table column sizes;
- rework UltraDMA mode dump code;
- remove PIO mode dump code that has never been finished;
- remove the duplicate interrupt status (the MRDMODE register bits mirror those
those in the CFR and ARTTIM23 registers) and fold the dump into single line;
- correct the style of the ?: operators...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The IDE core looks at the wrong bit when checking if the secondary channel is
enabled on PCI0646 -- CNTRL register bit 7 is read-ahead disable, bit 3 is the
correct one.
Starting with PCI0646U chip, the primary channel can also be enabled/disabled --
so, add 'enablebits' initializers to each 'ide_pci_device_t' structure, handling
the original PCI0646 via adding the init_setup() method and clearing the 'reg'
field there if necessary...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The driver's ide_dma_test_irq() method was reading the MRDMODE register even on
PCI0643/6 where it was write-only -- fix this by always reading the "backward-
compatible" interrupt bits, renaming dma_alt_stat to irq_stat as the interrupt
status bits are not coupled to DMA.
In addition, wrong interrupt bit was tested/cleared for the primary channel --
it's bit 2 in all the chip specs and the driver used bit 1... :-/
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix the multiword DMA and drop the single-word DMA support (which nobody will
miss, I think). In order to do it, a number of changes was necessary:
- rename program_drive_counts() to program_cycle_times(), pass to it cycle's
total/active times instead of the clock counts, and convert them into the
active/recovery clocks there instead of cmd64x_tune_pio() -- this causes
quantize_timing() to also move;
- contrarywise, move all the code handling the address setup timing into
cmd64x_tune_pio(), so that setting MWDMA mode wouldn't change address setup;
- remove from the speedproc() method the bogus code pretending to set the DMA
timings by twiddling bits in the BMIDE status register, handle setting MWDMA
by just calling program_cycle_times(); while at it, improve the style of that
whole switch statement;
- stop fiddling with the DMA capable bits in the speedproc() method -- they do
not enable DMA, and are properly dealt with by the dma_host_{on,off} methods;
- don't set hwif->swdma_mask in the init_hwif() method anymore.
In addition to those changes, do the following:
- in cmd64x_tune_pio(), when writing to ARTTIM23 register preserve the interrupt
status bit, eliminate local_irq_{save|restore}() around this code as there's
*no* actual race with the interrupt handler, and move cmdprintk() to a more
fitting place -- after ide_get_best_pio_mode() call;
- make {arttim|drwtim}_regs arrays single-dimensional, indexed with drive->dn;
- rename {setup|recovery}_counts[] into more fitting {setup|recovery}_values[];
- in the speedproc() method, get rid of the duplicate reads/writes from/to the
UDIDETCRx registers and of the extra variable used to store the transfer mode
value after filtering, use another method of determining master/slave drive,
and cleanup useless parens;
- beautify cmdprintk() output here and there.
While at it, remove meaningless comment about the driver being used only on
UltraSPARC and long non-relevant RCS tag. :-)
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fold the now equivalent code in the ide_dma_check() method into a mere call to
ide_use_dma(). Make config_for_dma() return non-zero if DMA mode has been set
and call it from the ide_dma_check() method instead of ide_dma_on().
Defer writing the DMA timings to the chip registers until DMA is really turned
on (and do not enable IORDY for DMA).
Remove unneeded code from the init_hwif() method, improve its overall looks.
Rename the dma_start(), ide_dma_check(), and ide_dma_lostirq() methods, and
also use more proper hwif->dma_command, fix printk() and comment in the latter
one as well. While at it, cleanup style in several places.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Get rid of the 'pio_speed' member of 'ide_drive_t' that was only used by this
driver by storing the PIO mode timings in the 'drive_data' instead -- this
allows us to greatly simplify the process of "reloading" of the chip's timing
register and do it right in sl82c150_dma_off_quietly() and to get rid of two
extra arguments to config_for_pio() -- which got renamed to sl82c105_tune_pio()
and now returns a PIO mode selected, with ide_config_drive_speed() call moved
into the tuneproc() method, now called sl82c105_tune_drive() with the code to
set drive's 'io_32bit' and 'unmask' flags in its turn moved to its proper place
in the init_hwif() method.
Also, while at it, rename get_timing_sl82c105() into get_pio_timings() and get
rid of the code in it clamping cycle counts to 32 which was both incorrect and
never executed anyway...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This patch removes the use of the TG3_FLAG_5701_REG_WRITE_BUG flag.
It's logic is only used to set a function pointer and thus the
logic can be collapsed and the flag removed.
[ Comment tidy by Christoph Hellwig. -DaveM ]
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
The reset was added a while back so that ASF could re-init whatever
MAC address it wanted to use after the MAC address was changed.
Instead of resetting, we can just keep MAC address 1 unchanged during
MAC address changes if MAC address 1 is different from MAC address 0.
This fixes 2 problems:
1. Bonding calls set_mac_address in contexts that cannot sleep.
It no longer sleeps with the chip reset removed.
2. When ASF shares the same MAC address as the NIC, it needs to
always do that even when the MAC address is changed.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change TG3_FLAG_SERDES_WOL_CAP to TG3_FLAG_WOL_CAP to make it easier
to manage WoL. This flag is now used consistently during ethtool WoL
setup and power setting changes.
Signed-off-by: Gary Zambrano <zambrano@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GPIO settings may change during reset and so the stored values in
tp->grc_local_ctrl should be cleared first.
Signed-off-by: Gary Zambrano <zambrano@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the NVRAM sizing procedure so that the driver can
take advantage of devices with 1:1 NVRAM strapping configurations. This
is useful in cases where the traditional NVRAM sizing method fails. In
the event that the flash size cannot be determined, the largest known
NVRAM size is used. The patch also removes support for 5755 NVRAM
devices that are not supported by Broadcom and adds explicit sizing for
this device.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Remove the check for skb->len greater than MTU when doing TSO.
When the destination has a smaller MSS than the source, a TSO packet
may be smaller than the MTU and we still need to process it as a TSO
packet.
2. On 5705A3 devices with TSO enabled, the DMA engine can hang due to a
hardware bug. This patch avoids the hanging condition by reducing the
DMA burst size.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ps3av:
- Move the definition of struct ps3av to ps3av.c, as it's locally used only.
- Kill ps3av.sem, use the existing ps3av.mutex instead.
- Make the 512-byte buffer in ps3av_do_pkt() static to reduce stack usage.
Its use is protected by a semaphore anyway.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ps3av: Replace the kernel_thread and the ping pong semaphores by a singlethread
workqueue and a completion.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ps3fb: Replace the kernel_thread and the semaphore by a proper kthread, which
is simply woken up when the screen must be updated
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The recent conversion from `memcpy' to `skb_copy_from_linear_data' removed a
few casts, which were needed to silence compiler warnings. Re-add them.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kill resource_size_t warnings by casting resource_size_t to unsigned long when
formatting Zorro bus resources, as they are always 32-bit.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Install the built-in macsonic interrupt handler on both IRQs when using
via_alt_mapping. Otherwise the rare interrupt that still comes from the
nubus slot will wedge the nubus.
$ cat /proc/interrupts
auto 2: 89176 via2
auto 3: 744367 sonic
auto 4: 0 scc
auto 6: 318363 via1
auto 7: 0 NMI
mac 9: 119413 framebuffer vbl
mac 10: 1971 ADB
mac 14: 198517 timer
mac 17: 89104 nubus
mac 19: 72 Mac ESP SCSI
mac 56: 629 sonic
mac 62: 1142593 ide0
Version 1 of this patch had a bug where a nubus sonic card would register
two interrupt handlers. Only a built-in sonic needs both.
Versions 2 and 3 needed some cleanups, as Raylynn Knight and Christoph
Hellwig pointed out (thanks).
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a potential problem in the timeout handling: don't free the DMA buffers
before resetting the chip.
Also a trivial cleanup. Bring macsonic and jazzsonic into sync.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a race condition in the transmit code, where the dma interrupt could update
the free tx buffer count concurrently and wedge the tx queue.
Fix the misuse of the rx frame status and rx frame length registers: no more
"fifo overrun" errors caused by the OFLOW bit being tested in the frame length
register (instead of the status register), and no more missed packets due to
incorrect length taken from status register (instead of the frame length
register).
Fix a panic (skb_over_panic BUG) caused by allocating and then copying an
incoming packet while the packet length register was changing.
Cut-and-paste the reset code from the powermac mace driver (mace.c), so the NIC
functions when MacOS does not initialise it (important for anyone wanting to
use the Emile boot loader).
Cut-and-paste the error counting and timeout recovery code from mace.c.
Fix over allocation of rx buffer memory (it's page order, not page count).
Converted to driver model.
Converted to DMA API.
Since I've run out of ways to make it fail, and since it performs well now,
promote the driver from EXPERIMENTAL status. Tested on both quadra 840av and
660av.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the flakiness in the CUDA ADB driver on m68k macs (keypresses getting
wedged down or ADB just going AWOL altogether).
The only IRQ used by this driver is the VIA shift register IRQ. The PowerMac
conditional code disables the other VIA IRQ sources, so don't mess with the
other IRQ flags in the common code -- m68k macs need them.
When polling, don't disable local interrupts when we only need to disable the
CUDA interrupt.
Unless polling, don't clear the shift register IRQ flag. On m68k macs this
creates a race that often breaks CUDA ADB.
Tested on Quadra 840av and LC630 (both m68k); also Beige G3 (powerpc).
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a crash caused by requests placed in the queue with the completed flag
already set. This lead to some ADB_SYNC requests returning early and their
request structs being popped off the stack while still queued. Stack corruption
ensued or an invalid request callback pointer was invoked or both. Eliminate
macii_retransmit() and its buggy implementation of macii_write(). Have
macii_queue_poll() fully initialise the request queues.
Fix a bug in macii_queue_poll() where the last_req pointer was not being set.
This caused some requests to leave the queue before being completed (and would
also corrupt the stack under certain conditions).
Fix a race in macii_start that could set the state machine to "reading" while
current_req was null.
No longer send poll commands with the ADBREQ_REPLY flag -- doing that caused
the replies to be stored in the request buffer where they were forgotten
about.
Don't autopoll by continuously sending new Talk commands. Get the controller to
do that for us. This reduces the ADB interrupt rate on an idle bus to about 5
per second. Only autopoll the devices that were probed.
Explicitly clear the interrupt flag when polling.
Use disable_irq rather than local_irq_save when polling.
Remove excess local_irq_save/restore pairs.
Improve bus timeout and service request detection.
Remove unused code (last_reply, adb_dir etc) and unneeded code (prefix_len,
first_byte etc).
Change TIP and TACK to their correct names on this ADB controller (ST_EVEN and
ST_ODD).
Add some commentry.
Add a generous quantity of sanity checks (BUG_ONs).
Let m68k macs use the adb_sync boot param too.
Tested on Mac II, Mac IIci, Quadra 650, Quadra 700 etc.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the support for C/NET nubus ethernet cards etc. Sync up the DP8390 driver
with the latest code in the mac68k repo.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sync the nubus defines with the latest code in the mac68k repo. Some of these
are needed for DP8390 driver update in the next patch.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Macintosh CS89x0 Ethernet: Netif updates
Addition of netif_stop_queue() before transmission by Michael Schmitz
skb_copy_{from,to}_linear_data() conversion by Geert Uytterhoeven
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update the atari fb to 2.6 by Michael Schmitz,
Reformatting and rewrite of bit plane functions by Roman Zippel,
A few more fixes by Geert Uytterhoeven.
Signed-off-by: Michael Schmitz <schmitz@debian.org>
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Atari keyboard and mouse support.
(reformating and Kconfig fixes by Roman Zippel)
Signed-off-by: Michael Schmitz <schmitz@debian.org>
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SCSI should be working on a TT (but someone should really try!) but causes
trouble on a Falcon (as in: it ate a filesystem of mine) at least when
used concurrently with IDE. I have the notion it's because locking of the
ST-DMA interrupt by IDE is broken in 2.6 (the IDE driver always complains
about trying to release an already-released ST-DMA). Needs more work, but
that's on the IDE or m68k interrupt side rather than SCSI.
Signed-off-by: Michael Schmitz <schmitz@debian.org>
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michael Chan