After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so quite a few
depend on CONFIG_PM or even may be dropped entirely in some cases.
Replace CONFIG_PM_RUNTIME with CONFIG_PM in the PM core code.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The number of and dependencies between high-level power management
Kconfig options make life much harder than necessary. Several
conbinations of them have to be tested and supported, even though
some of those combinations are very rarely used in practice (if
they are used in practice at all). Moreover, the fact that we
have separate independent Kconfig options for runtime PM and
system suspend is a serious obstacle for integration between
the two frameworks.
To overcome these difficulties, always select PM_RUNTIME if PM_SLEEP
is set. Among other things, this will allow system suspend callbacks
provided by bus types and device drivers to rely on the runtime PM
framework regardless of the kernel configuration.
Enthusiastically-acked-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If BL_SWITCHER is enabled but SUSPEND and CPU_IDLE is not enabled
we are getting following config warning.
warning: (BL_SWITCHER) selects CPU_PM which has unmet direct
dependencies (SUSPEND || CPU_IDLE)
It has been noticed that CPU_PM dependencies in this file are not really
required so let's remove these dependencies from CPU_PM.
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The vfree() function performs also input parameter validation. Thus the test
around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The IA64_HP_SIM dependency on PM_RUNTIME should be done in the arch
Kconfig instead of in the PM core. Move it accordingly.
NOTE: arch/ia64/Kconfig currently does a 'select PM', which since
commit 1eb208aea3 (PM: Make CONFIG_PM depend on (CONFIG_PM_SLEEP ||
CONFIG_PM_RUNTIME)) is effectively a noop unless PM_SLEEP or
PM_RUNTIME are set elsewhere.
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If no freeze_ops is set, trying to enter suspend-to-IDLE will cause a
nice oops in platform_suspend_prepare_late(). Add respective checks to
platform_suspend_prepare_late() and platform_resume_early() functions.
Fixes: a8d46b9e4e (ACPI / sleep: Rework the handling of ACPI GPE wakeup ...)
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch migrates swsusp_show_speed and its callers to using ktime_t instead
of 'struct timeval' which suffers from the y2038 problem.
Changes to swsusp_show_speed:
- use ktime_t for start and stop times
- pass start and stop times by value
Calling functions affected:
- load_image
- load_image_lzo
- save_image
- save_image_lzo
- hibernate_preallocate_memory
Design decisions:
- use ktime_t to preserve same granularity of reporting as before
- use centisecs logic as before to avoid 'div by zero' issues caused by
using seconds and nanoseconds directly
- use monotonic time (ktime_get()) since we only care about elapsed time.
Signed-off-by: Tina Ruchandani <ruchandani.tina@gmail.com>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If a device's dev_pm_ops::freeze callback fails during the QUIESCE
phase, we don't rollback things correctly calling the thaw and complete
callbacks. This could leave some devices in a suspended state in case of
an error during resuming from hibernation.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Clean up the code in process.c after recent changes to get rid of
unnecessary labels and goto statements.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
as per 0c740d0afc (introduce for_each_thread() to replace the buggy
while_each_thread()) get rid of do_each_thread { } while_each_thread()
construct and replace it by a more error prone for_each_thread.
This patch doesn't introduce any user visible change.
Suggested-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
PM freezer relies on having all tasks frozen by the time devices are
getting frozen so that no task will touch them while they are getting
frozen. But OOM killer is allowed to kill an already frozen task in
order to handle OOM situtation. In order to protect from late wake ups
OOM killer is disabled after all tasks are frozen. This, however, still
keeps a window open when a killed task didn't manage to die by the time
freeze_processes finishes.
Reduce the race window by checking all tasks after OOM killer has been
disabled. This is still not race free completely unfortunately because
oom_killer_disable cannot stop an already ongoing OOM killer so a task
might still wake up from the fridge and get killed without
freeze_processes noticing. Full synchronization of OOM and freezer is,
however, too heavy weight for this highly unlikely case.
Introduce and check oom_kills counter which gets incremented early when
the allocator enters __alloc_pages_may_oom path and only check all the
tasks if the counter changes during the freezing attempt. The counter
is updated so early to reduce the race window since allocator checked
oom_killer_disabled which is set by PM-freezing code. A false positive
will push the PM-freezer into a slow path but that is not a big deal.
Changes since v1
- push the re-check loop out of freeze_processes into
check_frozen_processes and invert the condition to make the code more
readable as per Rafael
Fixes: f660daac47 (oom: thaw threads if oom killed thread is frozen before deferring)
Cc: 3.2+ <stable@vger.kernel.org> # 3.2+
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The existing implementation of swsusp_free iterates over all
pfns in the system and checks every bit in the two memory
bitmaps.
This doesn't scale very well with large numbers of pfns,
especially when the bitmaps are not populated very densly.
Change the algorithm to iterate over the set bits in the
bitmaps instead to make it scale better in large memory
configurations.
Also add a memory_bm_clear_current() helper function that
clears the bit for the last position returned from the
memory bitmap.
This new version adds a !NULL check for the memory bitmaps
before they are walked. Not doing so causes a kernel crash
when the bitmaps are NULL.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The ACPI GPE wakeup from suspend-to-idle is currently based on using
the IRQF_NO_SUSPEND flag for the ACPI SCI, but that is problematic
for a couple of reasons. First, in principle the ACPI SCI may be
shared and IRQF_NO_SUSPEND does not really work well with shared
interrupts. Second, it may require the ACPI subsystem to special-case
the handling of device notifications depending on whether or not
they are received during suspend-to-idle in some places which would
lead to fragile code. Finally, it's better the handle ACPI wakeup
interrupts consistently with wakeup interrupts from other sources.
For this reason, remove the IRQF_NO_SUSPEND flag from the ACPI SCI
and use enable_irq_wake()/disable_irq_wake() with it instead, which
requires two additional platform hooks to be added to struct
platform_freeze_ops.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Rename several local functions related to platform handling during
system suspend resume in suspend.c so that their names better
reflect their roles.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Subsequent change sets will add platform-related operations between
dpm_suspend_late() and dpm_suspend_noirq() as well as between
dpm_resume_noirq() and dpm_resume_early() in suspend_enter(), so
export these functions for suspend_enter() to be able to call them
separately and split the invocations of dpm_suspend_end() and
dpm_resume_start() in there accordingly.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Also adds a class type PM_QOS_SUM that aggregates the values by summing them.
It can be used by memory controllers to calculate the optimum clock frequency
based on the bandwidth needs of the different memory clients.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch moves Exynos PM domain code to use the new generic PM domain
look-up framework introduced in previous patches, thus also allowing
the new code to be compiled with CONFIG_ARCH_EXYNOS.
This patch was originally submitted by Tomasz Figa when he was employed
by Samsung.
Link: http://marc.info/?l=linux-pm&m=139955336002083&w=2
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch introduces generic code to perform PM domain look-up using
device tree and automatically bind devices to their PM domains.
Generic device tree bindings are introduced to specify PM domains of
devices in their device tree nodes.
Backwards compatibility with legacy Samsung-specific PM domain bindings
is provided, but for now the new code is not compiled when
CONFIG_ARCH_EXYNOS is selected to avoid collision with legacy code.
This will change as soon as the Exynos PM domain code gets converted to
use the generic framework in further patch.
This patch was originally submitted by Tomasz Figa when he was employed
by Samsung.
Link: http://marc.info/?l=linux-pm&m=139955349702152&w=2
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch adds another suspend_resume trace event for analyze_suspend
to capture. The resume_console call can take several hundred milliseconds
if the printk buffer is full of debug info. The tool will now inform
testers of the wasted time and encourage them to disable it in
production builds.
Signed-off-by: Todd Brandt <todd.e.brandt@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Enhanced test_suspend boot paramter to repeat tests multiple times,
by adding optional repeat count. The new boot param syntax:
test_suspend="mem|freeze|standby[,N]"
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Added freeze as one of the option for test_suspend boot param.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
After commit d431cbc53c (PM / sleep: Simplify sleep states sysfs
interface code) the pm_states[] array is not populated initially,
which causes setup_test_suspend() to always fail and the suspend
testing during boot doesn't work any more.
Fix the problem by using pm_labels[] instead of pm_states[] in
setup_test_suspend() and storing a pointer to the label of the
sleep state to test rather than the number representing it,
because the connection between the state numbers and labels is
only established by suspend_set_ops().
Fixes: d431cbc53c (PM / sleep: Simplify sleep states sysfs interface code)
Reported-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
It sometimes may be necessary to abort a system suspend in
progress or wake up the system from suspend-to-idle even if the
pm_wakeup_event()/pm_stay_awake() mechanism is not enabled.
For this purpose, introduce a new global variable pm_abort_suspend
and make pm_wakeup_pending() check its value. Also add routines
for manipulating that variable.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When the machine doesn't well handle the e820 persistent when hibernate
resuming, then it may cause page fault when writing image to snapshot
buffer:
[ 17.929495] BUG: unable to handle kernel paging request at ffff880069d4f000
[ 17.933469] IP: [<ffffffff810a1cf0>] load_image_lzo+0x810/0xe40
[ 17.933469] PGD 2194067 PUD 77ffff067 PMD 2197067 PTE 0
[ 17.933469] Oops: 0002 [#1] SMP
...
The ffff880069d4f000 page is in e820 reserved region of resume boot
kernel:
[ 0.000000] BIOS-e820: [mem 0x0000000069d4f000-0x0000000069e12fff] reserved
...
[ 0.000000] PM: Registered nosave memory: [mem 0x69d4f000-0x69e12fff]
So snapshot.c mark the pfn to forbidden pages map. But, this
page is also in the memory bitmap in snapshot image because it's an
original page used by image kernel, so it will also mark as an
unsafe(free) page in prepare_image().
That means the page in e820 when resuming mark as "forbidden" and
"free", it causes get_buffer() treat it as an allocated unsafe page.
Then snapshot_write_next() return this page to load_image, load_image
writing content to this address, but this page didn't really allocated
. So, we got page fault.
Although the root cause is from BIOS, I think aggressive check and
significant message in kernel will better then a page fault for
issue tracking, especially when serial console unavailable.
This patch adds code in mark_unsafe_pages() for check does free pages in
nosave region. If so, then it print message and return fault to stop whole
S4 resume process:
[ 8.166004] PM: Image loading progress: 0%
[ 8.658717] PM: 0x6796c000 in e820 nosave region: [mem 0x6796c000-0x6796cfff]
[ 8.918737] PM: Read 2511940 kbytes in 1.04 seconds (2415.32 MB/s)
[ 8.926633] PM: Error -14 resuming
[ 8.933534] PM: Failed to load hibernation image, recovering.
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Lee, Chun-Yi <jlee@suse.com>
[rjw: Subject]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When a memory bitmap is fully populated on a large memory
machine (several TB of RAM) it can take more than a minute
to walk through all bits. This causes the soft lockup
detector on these machine to report warnings.
Avoid this by touching the soft lockup watchdog in the
memory bitmap walking code.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The radix tree implementatio is proved to work the same as
the old implementation now. So the old implementation can be
removed to finish the switch to the radix tree for the
memory bitmaps.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The existing implementation of swsusp_free iterates over all
pfns in the system and checks every bit in the two memory
bitmaps.
This doesn't scale very well with large numbers of pfns,
especially when the bitmaps are not populated very densly.
Change the algorithm to iterate over the set bits in the
bitmaps instead to make it scale better in large memory
configurations.
Also add a memory_bm_clear_current() helper function that
clears the bit for the last position returned from the
memory bitmap.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add code to remember the last position that was requested in
the radix tree. Use it as a cache for faster linear walking
of the bitmap in the memory_bm_rtree_next_pfn() function
which is also added with this patch.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add a function to find a bit in the radix tree for a given
pfn. Also add code to the memory bitmap wrapper functions to
use the radix tree together with the existing memory bitmap
implementation.
On read accesses compare the results of both bitmaps to make
sure the radix tree behaves the same way.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch adds the code to allocate and build the radix
tree to store the memory bitmap. The old data structure is
left in place until the radix tree implementation is
finished.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The PM workqueue is going to be used by ACPI PM notify handlers
regardless of whether or not runtime PM is configured, so move
it out of #ifdef CONFIG_PM_RUNTIME.
Do that in three places in the ACPI device PM code.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
After the introduction of freeze_ops it makes more sense to move
all of the platform suspend operations to separate functions that
each will do all of the necessary checks and choose the right
callback to execute istead of doing all that in the core code
which makes it generally harder to follow.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since the OPP layer is a kernel library which has been converted to be
directly selectable by its callers rather than user selectable and
requiring architectures to enable it explicitly the ARCH_HAS_OPP symbol
has become redundant and can be removed. Do so.
Signed-off-by: Mark Brown <broonie@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Nishanth Menon <nm@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Simplify the sleep states sysfs interface /sys/power/state code by
redefining pm_states[] as an array of pointers to constant strings
such that only the entries corresponding to valid states are set.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ftrace_stop() and ftrace_start() were added to the suspend and hibernate
process because there was some function within the work flow that caused
the system to reboot if it was traced. This function has recently been
found (restore_processor_state()). Now there's no reason to disable
function tracing while we are going into suspend or hibernate, which means
that being able to trace this will help tremendously in debugging any
issues with suspend or hibernate.
This also means that the ftrace_stop/start() functions can be removed
and simplify the function tracing code a bit.
Link: http://lkml.kernel.org/r/1518201.VD9cU33jRU@vostro.rjw.lan
Acked-by: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Reviewed-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
This patch fixes a NULL pointer dereference issue introduced by
commit 1f0b63866f (ACPI / PM: Hold ACPI scan lock over the "freeze"
sleep state).
Fixes: 1f0b63866f (ACPI / PM: Hold ACPI scan lock over the "freeze" sleep state)
Link: http://marc.info/?l=linux-pm&m=140541182017443&w=2
Reported-and-tested-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The commit [247bc037: PM / Sleep: Mitigate race between the freezer
and request_firmware()] introduced the finer state control, but it
also leads to a new bug; for example, a bug report regarding the
firmware loading of intel BT device at suspend/resume:
https://bugzilla.novell.com/show_bug.cgi?id=873790
The root cause seems to be a small window between the process resume
and the clear of usermodehelper lock. The request_firmware() function
checks the UMH lock and gives up when it's in UMH_DISABLE state. This
is for avoiding the invalid f/w loading during suspend/resume phase.
The problem is, however, that usermodehelper_enable() is called at the
end of thaw_processes(). Thus, a thawed process in between can kick
off the f/w loader code path (in this case, via btusb_setup_intel())
even before the call of usermodehelper_enable(). Then
usermodehelper_read_trylock() returns an error and request_firmware()
spews WARN_ON() in the end.
This oneliner patch fixes the issue just by setting to UMH_FREEZING
state again before restarting tasks, so that the call of
request_firmware() will be blocked until the end of this function
instead of returning an error.
Fixes: 247bc03742 (PM / Sleep: Mitigate race between the freezer and request_firmware())
Link: https://bugzilla.novell.com/show_bug.cgi?id=873790
Cc: 3.4+ <stable@vger.kernel.org> # 3.4+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Changes kASLR from being compile-time selectable (blocked by
CONFIG_HIBERNATION), to being boot-time selectable (with hibernation
available by default) via the "kaslr" kernel command line.
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
To support using kernel features that are not compatible with hibernation,
this creates the "nohibernate" kernel boot parameter to disable both
hibernation and resume. This allows hibernation support to be a boot-time
choice instead of only a compile-time choice.
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Adds trace events that give finer resolution into suspend/resume. These
events are graphed in the timelines generated by the analyze_suspend.py
script. They represent large areas of time consumed that are typical to
suspend and resume.
The event is triggered by calling the function "trace_suspend_resume"
with three arguments: a string (the name of the event to be displayed
in the timeline), an integer (case specific number, such as the power
state or cpu number), and a boolean (where true is used to denote the start
of the timeline event, and false to denote the end).
The suspend_resume trace event reproduces the data that the machine_suspend
trace event did, so the latter has been removed.
Signed-off-by: Todd Brandt <todd.e.brandt@intel.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fix a trivial comment typo (s/mam/map) in kernel/power/swap.c.
Signed-off-by: Niv Yehezkel <executerx@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On some systems the platform doesn't support neither
PM_SUSPEND_MEM nor PM_SUSPEND_STANDBY, so PM_SUSPEND_FREEZE is the
only available system sleep state. However, some user space frameworks
only use the "mem" and (sometimes) "standby" sleep state labels, so
the users of those systems need to modify user space in order to be
able to use system suspend at all and that is not always possible.
For this reason, add a new kernel command line argument,
relative_sleep_states, allowing the users of those systems to change
the way in which the kernel assigns labels to system sleep states.
Namely, for relative_sleep_states=1, the "mem", "standby" and "freeze"
labels will enumerate the available system sleem states from the
deepest to the shallowest, respectively, so that "mem" is always
present in /sys/power/state and the other state strings may or may
not be presend depending on what is supported by the platform.
Update system sleep states documentation to reflect this change.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use the observation that, for platform-dependent sleep states
(PM_SUSPEND_STANDBY, PM_SUSPEND_MEM), a given state is either
always supported or always unsupported and store that information
in pm_states[] instead of calling valid_state() every time we
need to check it.
Also do not use valid_state() for PM_SUSPEND_FREEZE, which is always
valid, and move the pm_test_level validity check for PM_SUSPEND_FREEZE
directly into enter_state().
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
To allow sleep states corresponding to the "mem", "standby" and
"freeze" lables to be different from the pm_states[] indexes of
those strings, introduce struct pm_sleep_state, consisting of
a string label and a state number, and turn pm_states[] into an
array of objects of that type.
This modification should not lead to any functional changes.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The OPP code is an in kernel library selected by its users, there is no
no architecture code required to implement it and enabling it without a
user just increases the kernel size. Since the users select rather than
depend on it just remove the ability to directly set the option from
Kconfig.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Nishanth Menon <nm@ti.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In the original code "resume_delay" is an int so on 64 bits, the call to
kstrtoul() will cause memory corruption. We may as well fix a style
issue here as well and make "resume_delay" unsigned int, since that's
what we pass to ssleep().
Fixes: 317cf7e5e8 (PM / hibernate: convert simple_strtoul to kstrtoul)
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The "freeze" sleep state suffers from the same issue that was
addressed by commit ad07277e82 (ACPI / PM: Hold acpi_scan_lock over
system PM transitions) for ACPI sleep states, that is, things break
if ->remove() is called for devices whose system resume callbacks
haven't been executed yet.
It also can be addressed in the same way, by holding the ACPI scan
lock over the "freeze" sleep state and PM transitions to and from
that state, but ->begin() and ->end() platform operations for the
"freeze" sleep state are needed for this purpose.
This change has been tested on Acer Aspire S5 with Thunderbolt.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Replace obsolete function.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If freeze_enter() is called, we want to bypass the current cpuidle
governor and always use the deepest available (that is, not disabled)
C-state, because we want to save as much energy as reasonably possible
then and runtime latency constraints don't matter at that point, since
the system is in a sleep state anyway.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Aubrey Li <aubrey.li@linux.intel.com>
Rafael J. Wysocki