Previously, the mesh STA responds to probe request from legacy STA
but now it will only respond to legacy STA if the legacy STA does include
the specific mesh ID or wildcard mesh ID in the probe request.
The iw patch "iw: scan using meshid" can be used either by legacy STA
or by mesh STA to do active scanning by inserting the mesh ID in the
probe request frame.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@cozybit.com>
Acked-by: Thomas Pedersen <thomas@cozybit.com>
Acked-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Set the Forwarding bit in Mesh Capability Info according
to dot11MeshForwarding as defined in IEEE 802.11-2012
section 8.4.2.100.8.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The various components accessing the bitrates table must use consider
the used channel bandwidth to select only available rates or calculate
the bitrate correctly.
There are some rates in reduced bandwidth modes which can't be
represented as multiples of 500kbps, like 2.25 MBit/s in 5 MHz mode. The
standard suggests to round up to the next multiple of 500kbps, just do
that in mac80211 as well.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
[make rate unsigned in ieee80211_add_tx_radiotap_header(), squash fix]
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
This is a collection of minor fixes:
* don't allow HT IEs in IBSS for 5/10 MHz
* don't allow HT IEs in Mesh for 5/10 MHz
* don't downgrade from/to 5 and 10 MHz channels
* don't try HT rates for 5 and 10 MHz channels when selecting rates
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of updating the mesh beacon immediately when
requested (which would require the sdata_lock()), defer it
to the mac80211 workqueue.
Fixes yet another deadlock on calling sta_info_flush()
with the sdata_lock() held from ieee80211_stop_mesh(). We
could just drop the sdata_lock() around the
mesh_sta_cleanup() call, but this path is also taken from
several non-locked error paths.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
[fix comment position]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently mesh uses mandatory rates as the default basic rates. Allow basic
rates to be configured during mesh join. Basic rates are applied only if
channel is also provided with mesh join command.
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
[some whitespace fixes, refuse basic rates w/o channel]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The time it takes to see the peer link expire may differ
by a minute since sta_expire() is run once a minute as a
mesh housekeeping task.
Signed-off-by: Colleen Twitty <colleen@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The patch "cfg80211/mac80211: use cfg80211 wdev mutex in
mac80211" introduced several deadlocks by converting the
ifmsh->mtx to wdev->mtx. Solve these by:
1. drop the cancel_work_sync() in ieee80211_stop_mesh().
Instead make the mesh work conditional on whether the mesh
is running or not.
2. lock the mesh work with sdata_lock() to protect beacon
updates and prevent races with wdev->mesh_id_len or
cfg80211.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Cap max peerings at 63 in accordance with IEEE-2012 8.4.2.100.7.
Triggers a beacon regeneration every time the number of peerings changes.
Previously this would only happen if the "accepting peerings" bit changed.
Signed-off-by: Jacob Minshall <jacob@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Using separate locks in cfg80211 and mac80211 has always
caused issues, for example having to unlock in places in
mac80211 to call cfg80211, which even needed a framework
to make cfg80211 calls after some functions returned etc.
Additionally, I suspect some issues people have reported
with the cfg80211 state getting confused could be due to
such issues, when cfg80211 is asking mac80211 to change
state but mac80211 is in the process of telling cfg80211
that the state changed (in another way.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Previously the mesh_auth_id was disabled. Instead set the
correct mesh authentication bit based on the mesh setup.
Signed-off-by: Colleen Twitty <colleen@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
VHT introduces multiple IEs that need to be parsed for a
wide bandwidth channel switch. Two are (currently) needed
in mac80211:
* wide bandwidth channel switch element
* channel switch wrapper element
The former is contained in the latter for beacons and probe
responses, but not for the spectrum management action frames
so the IE parser needs a new argument to differentiate them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It's always just one byte, so check for that and
remove the length field from the parser struct.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
I found another crash when deleting lots of virtual stations
in a congested environment. I think the problem is that
the ieee80211_mlme_notify_scan_completed could call
ieee80211_restart_sta_timer for a stopped interface
that was about to be deleted.
With the following patch I am unable to reproduce the
crash.
Signed-off-by: Ben Greear <greearb@candelatech.com>
[move check, also make the same change in mesh]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Earlier mac80211 would check whether some kind of mesh
security was enabled, when the real question was "is the
MPM in userspace"?
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remove not used any longer suspend/resume code.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If mesh plink debugging is enabled, this gets annoying in
a crowded environment, fast.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's various code with strange indentation,
questionable loop and locking constructs, etc.
The bigger change is moving the "sdata" argument
to the first argument of all functions, like all
other mac80211 functions that have one.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Mesh interfaces will now respond to any broadcast (or
matching directed mesh) probe requests with a probe
response.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Previously, the entire mesh beacon would be generated each
time the beacon timer fired. Instead generate a beacon
head and tail (so the TIM can easily be inserted when mesh
power save is on) when starting a mesh or the MBSS
parameters change.
Also add a mutex for protecting beacon updates and
preventing leaks.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A few mesh utility functions will call
ieee80211_bss_info_change_notify(), and then the caller
might notify the driver of the same change again. Avoid
this redundancy by propagating the BSS changes and
generally calling bss_info_change_notify() once per
change.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There seems to be no reason, why it has to be limited to 2.4 GHz.
Signed-off-by: Emanuel Taube <emanuel.taube@gmail.com>
[remove 'local' variable]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The patch "mac80211: clean up mesh sta allocation warning"
moved some mesh initialization into a path which is only
called when the kernel handles peering. This causes a hang
when mac80211 tries to clean up a userspace-allocated
station entry and delete a timer which has never been
initialized.
To avoid this, only do any mesh sta peering teardown if
the kernel is actually handling it.
The same is true when quiescing before suspend.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add routines to
- maintain a PS mode for each peer and a non-peer PS mode
- indicate own PS mode in transmitted frames
- track neighbor STAs power modes
- buffer frames when neighbors are in PS mode
- add TIM and Awake Window IE to beacons
- release frames in Mesh Peer Service Periods
Add local_pm to sta_info to represent the link-specific power
mode at this station towards the remote station. When a peer
link is established, use the default power mode stored in mesh
config. Update the PS status if the peering status of a neighbor
changes.
Maintain a mesh power mode for non-peer mesh STAs. Set the
non-peer power mode to active mode during peering. Authenticated
mesh peering is currently not working when either node is
configured to be in power save mode.
Indicate the current power mode in transmitted frames. Use QoS
Nulls to indicate mesh power mode transitions.
For performance reasons, calls to the function setting the frame
flags are placed in HWMP routing routines, as there the STA
pointer is already available.
Add peer_pm to sta_info to represent the peer's link-specific
power mode towards the local station. Add nonpeer_pm to
represent the peer's power mode towards all non-peer stations.
Track power modes based on received frames.
Add the ps_data structure to ieee80211_if_mesh (for TIM map, PS
neighbor counter and group-addressed frame buffer).
Set WLAN_STA_PS flag for STA in PS mode to use the unicast frame
buffering routines in the tx path. Update num_sta_ps to buffer
and release group-addressed frames after DTIM beacons.
Announce the awake window duration in beacons if in light or
deep sleep mode towards any peer or non-peer. Create a TIM IE
similarly to AP mode and add it to mesh beacons. Parse received
Awake Window IEs and check TIM IEs for buffered frames.
Release frames towards peers in mesh Peer Service Periods. Use
the corresponding trigger frames and monitor the MPSP status.
Append a QoS Null as trigger frame if neccessary to properly end
the MPSP. Currently, in HT channels MPSPs behave imperfectly and
show large delay spikes and frame losses.
Signed-off-by: Marco Porsch <marco@cozybit.com>
Signed-off-by: Ivan Bezyazychnyy <ivan.bezyazychnyy@gmail.com>
Signed-off-by: Mike Krinkin <krinkin.m.u@gmail.com>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The standard mandates mesh STAs to set the ERP Short Slot
Time capability info bit in beacons to 0. Even though this
is their way of disallowing short slot time for mesh STAs,
there should be no harm in enabling it if we determine all
STAs in the current MBSS support ERP rates.
Increases throughput about 20% for legacy rates when
enabled.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move the default mesh beacon interval and DTIM period to cfg80211
and make them accessible to nl80211. This enables setting both
values when joining an MBSS.
Previously the DTIM parameter was not set by mac80211 so the
driver's default value was used.
Signed-off-by: Marco Porsch <marco@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of checking every time bss_info_changed is called,
assign the pointer once depending on the interface type
and then leave it untouched until the interface type is
changed. This makes the ieee80211_bss_info_change_notify()
now a simple wrapper to call the driver only.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of calculating in ieee80211_bss_info_change_notify()
whether beaconing should be enabled or not, set it in the
correct places in the callers. This simplifies the logic in
this function at the expense of offchannel, but is also more
robust.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In a file that's only built when CONFIG_MAC80211_MESH
is defined, having an #ifdef on the same is entirely
pointless, so remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When all interfaces have been removed, there can't
be any stations left over, so there's no need to
flush again. Remove this, and all code associated
with it, which also simplifies the function.
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use short slot time in 5GHz for mesh. The performance is
increased from 16.4Mbps to 23.4Mbps for two directly
connected mesh STAs operating in legacy rate using iperf
measurement. Almost similar to the results claimed in IBSS
mode.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
[call ieee80211_get_sdata_band() only once]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The array of rmc_entrys is redundant since only the
list_head is used. Make this an array of list_heads
instead and save ~6k per vif at runtime :D
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Convert mac80211 (and where necessary, some drivers a
little bit) to the new channel definition struct.
This will allow extending mac80211 for VHT, which is
currently restricted to channel contexts since there
are no drivers using that which makes it easier. As
I also don't care about VHT for drivers not using the
channel context API, I won't convert the previous API
to VHT support.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Before, a mesh STA would execute some code on behalf of AP or IBSS
beacons. Since the mesh stack currently does not consider anything but
other mesh STAs interesting, limit processing to just these and save a
little overhead.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
estab_plinks is not a statistics member. Hence move estab_plinks from
struct mesh_stat to struct ieee80211_if_mesh
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of operating on a single channel only,
use the new channel context infrastructure in
all mac80211 code.
This enables drivers that want to use the new
channel context infrastructure to use multiple
channels, while nothing should change for all
the other drivers that don't support it.
Right now this disables both TX power settings
and spatial multiplexing powersave. Both need
to be re-enabled on a channel context basis.
Additionally, when channel contexts are used
drop the connection when channel switch is
received rather than trying to handle it. This
will have to be improved later.
[With fixes from Eliad and Emmanuel incorporated]
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Using local->_oper_channel_type in the mesh code is
completely wrong as this value is the combination
of the various interface channel types and can be
a different value from the mesh interface in case
there are multiple virtual interfaces.
Use sdata->vif.bss_conf.channel_type instead as it
tracks the per-vif channel type.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ieee80211_bss_info_change_notify is called everytime a peer link is established
or closed, because the accepting_plinks flag in the meshconf IE *might* have changed.
With this patch the corresponding functions return the BSS_CHANGED_BEACON flag when a beacon update is necessary.
Also it makes mesh_accept_plinks_update the common place to update the accepting_plinks flag.
mesh_accept_plinks_update is called upon plink change and also periodically from ieee80211_mesh_housekeeping.
Thus, it also picks up changes of local->num_sta.
Signed-off-by: Marco Porsch <marco.porsch@etit.tu-chemnitz.de>
Acked-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is not necessary to stop the mesh beacon in the mac80211 ndo_stop
handler, since cfg80211 has already left the mesh on NETDEV_GOING_DOWN
notification.
Also some improvements to ieee80211_stop_mesh():
- flush mpath entries.
- flush sta entries per-sdata so we don't remove entries belonging to
other vifs on the same hw.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The mesh path timer needs to be canceled when
leaving the mesh as otherwise it could fire
after the interface has been removed already.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's a corner case that can happen when we
suspend with a timer running, then resume and
disconnect. If we connect again, suspend and
resume we might start timers that shouldn't be
running. Reset the timer flags to avoid this.
This affects both mesh and managed modes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of assuming the carrier is on all
the time in mesh manage it with joining
and leaving the mesh.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Using hw.conf.channel is wrong as it could be the
temporary channel if any function like the beacon
get function is called while scanning or during
other temporary out-of-channel activities.
Use oper_channel instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix incorrect start markers, wrapped summary lines, missing section
breaks, incorrect separators, and some name mismatches.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a few things that make the logging and
debugging in mac80211 less useful than it should
be right now:
* a lot of messages should be pr_info, not pr_debug
* wholesale use of pr_debug makes it require *both*
Kconfig and dynamic configuration
* there are still a lot of ifdefs
* the style is very inconsistent, sometimes the
sdata->name is printed in front
Clean up everything, introducing new macros and
separating out the station MLME debugging into
a new Kconfig symbol.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mesh_path_root_timer is invoked once the dot11MeshHWMPRootMode
is larger than 1. This patch also adds the backward compatible
to the previous setting on dot11MeshHWMPRootMode. If the user
configures as follow, it will still trigger the proactive RANN
with Gate Announcement.
iw mesh0 set mesh_param mesh_hwmp_rootmode 1
iw mesh0 set mesh_param mesh_gate_announcements 1
similar to the following setting:
iw mesh0 set mesh_param mesh_hwmp_rootmode 4
iw mesh0 set mesh_param mesh_gate_announcements 1
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
[line-break commit log]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Generate the proactive PREQ element as defined in
Sec. 13.10.9.3 (Case C) of IEEE Std. 802.11-2012
based on the selection of dot11MeshHWMPRootMode as follow:
dot11MeshHWMPRootMode (2) is proactivePREQnoPREP
dot11MeshHWMPRootMode (3) is proactivePREQwithPREP
The proactive PREQ is generated based on the interval
defined by dot11MeshHWMProotInterval.
With this change, proactive RANN element is now generated
if the dot11MeshHWMPRootMode is set to (4) instead of (1).
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
[line-break commit log]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Chun-Yeow Yeoh