Extends FSL EHCI platform driver glue layer to support
MPC5121 USB controllers. MPC5121 Rev 2.0 silicon EHCI
registers are in big endian format. The appropriate flags
are set using the information in the platform data structure.
MPC83xx system interface registers are not available on
MPC512x, so the access to these registers is isolated in
MPC512x case. Furthermore the USB controller clocks
must be enabled before 512x register accesses which is
done by providing platform specific init callback.
The MPC512x internal USB PHY doesn't provide supply voltage.
For boards using different power switches allow specifying
DRVVBUS and PWR_FAULT signal polarity of the MPC5121 internal
PHY using "fsl,invert-drvvbus" and "fsl,invert-pwr-fault"
properties in the device tree USB nodes. Adds documentation
for this new device tree bindings.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Also modifiy the document of cell-index in SPI controller. Add the
SPI flash(s25fl128p01) support on p4080ds and mpc8536ds board.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This list moved to lists.ozlabs.org quite some time ago.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Marvell and GPIO bindings live in their own files, so the TOC should not
mention them.
Also fix chapters numbering.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Cc: Jerry Huang <Chang-Ming.Huang@freescale.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Below you will find an updated version from the original series bunching all patches into one big patch
updating broken web addresses that are located in Documentation/*
Some of the addresses date as far far back as 1995 etc... so searching became a bit difficult,
the best way to deal with these is to use web.archive.org to locate these addresses that are outdated.
Now there are also some addresses pointing to .spec files some are located, but some(after searching
on the companies site)where still no where to be found. In this case I just changed the address
to the company site this way the users can contact the company and they can locate them for the users.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Cc: Paulo Marques <pmarques@grupopie.com>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Michael Neuling <mikey@neuling.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch improves the recovery of the MPC's I2C bus from errors like bus
hangs resulting in timeouts:
1. make the bus timeout configurable, as it depends on the bus clock and
the attached slave chip(s); default is still 1 second;
2. detect any of the cases indicated by the CF, BB and RXAK MSR flags if a
timeout occurs, and add a missing (required) MAL reset;
3. use a more reliable method to fixup the bus if a hang has been detected.
The sequence is sent 9 times which seems to be necessary if a slave
"misses" more than one clock cycle. For 400 kHz bus speed, the fixup is
also ~70us (81us vs. 150us) faster.
Tested on a custom Lite5200b derived board, with a Dallas RTC, AD sensors
and NXP IO expander chips attached to the i2c.
Changes vs. v1:
- use improved bus fixup sequence for all chips (not only the 5200)
- calculate real clock from defaults if no clock is given in the device tree
- better description (I hope) of the changes.
I didn't split the changes in this file into three parts as recommended by
Grant, as they actually belong together (i.e. they address one single
problem, just in three places of one single source file).
Signed-off-by: Albrecht Dreß <albrecht.dress@arcor.de>
[grant.likely@secretlab.ca: fixup for ->node to ->dev.of_node transition]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Adds support for encoding display mode information
in the device tree using verbatim EDID block.
If the EDID entry in the DIU node is present, the
driver will build mode database using EDID data
and allow setting the display modes from this database.
Otherwise display mode will be set using mode
entries from driver's internal database as usual.
This patch also updates device tree bindings.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Update compatible and interrupt properties description.
Furthermore an example for the MPC5121 has been added.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
By setting "reset_type" to one of the following values, the default
software reset mechanism may be overidden. Here the possible values of
"reset_type":
1 - PPC4xx core reset
2 - PPC4xx chip reset
3 - PPC4xx system reset (default)
This will be used by a new PPC440SPe board port, which needs a "chip
reset" instead of the default "system reset" to be asserted.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Fix obvious cases of "it's" being used when "its" was meant.
Signed-off-by: Francis Galiegue <fgaliegue@gmail.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Define a binding for embedding a QE firmware blob into the device tree. Also
define a new property for the QE node that links to a firmware node.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds the MPC5121 to the list of supported devices,
enhances the doc of the "clock-frequency" property and removes
the obsolete "cell-index", "device_type" and "fsl-i2c" property.
Furthermore an example for the MPC5121 has been added.
Signed-off-by: Wolfgang Grandegger <wg@denx.de>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Added devicetree binding documentation for gpios used as chipselect. The
code to evaluate these is already present in spi_mpc8xxx.c.
Signed-off-by: Ernst Schwab <eschwab@online.de>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Support for MPC5121 PSC UART in the mpc52xx_uart driver
added new DTS properties for FSL MPC5121 PSC FIFO Controller.
Provide documentation of the new properties and some examples.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
powerpc: Extended ptrace interface
From: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Based on patches originally written by Torez Smith.
Add a new extended ptrace interface so that user-space has a single
interface for powerpc, without having to know the specific layout
of the debug registers.
Implement:
PPC_PTRACE_GETHWDEBUGINFO
PPC_PTRACE_SETHWDEBUG
PPC_PTRACE_DELHWDEBUG
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Acked-by: David Gibson <dwg@au1.ibm.com>
Cc: Torez Smith <lnxtorez@linux.vnet.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Sergio Durigan Junior <sergiodj@br.ibm.com>
Cc: Thiago Jung Bauermann <bauerman@br.ibm.com>
Cc: linuxppc-dev list <Linuxppc-dev@ozlabs.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The IRQ probing is needlessly complex. All off the 83xx device trees in
arch/powerpc/boot/dts/ specify 5 interrupts per DMA controller: one for the
controller, and one for each channel. These interrupts are all attached to
the same IRQ line.
This causes an interesting situation if two channels interrupt at the same
time. The per-controller handler will handle the first channel, and the
per-channel handler will handle the remaining channels.
Instead of this mess, we fix the bug in the per-controller handler, and
make it handle all channels that generated an interrupt. When a
per-controller handler is specified in the device tree, we prefer to use
the shared handler instead of the per-channel handler.
The 85xx/86xx controllers do not have a per-controller interrupt, and
instead use a per-channel interrupt. This behavior has not been changed.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This patch adds documentation for the MSCAN OF device bindings for
the MPC512x and moves the one for the MPC5200 to the new common file
"Documentation/powerpc/dts-bindings/fsl/can.txt".
Signed-off-by: Wolfgang Grandegger <wg@denx.de>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a device tree source file for the Nintendo Wii video game console.
Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Acked-by: Segher Boessenkool <segher@kernel.crashing.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add a device tree source file for the Nintendo GameCube video game console.
Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Acked-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds new version of the PPC440SPe ADMA driver.
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Add bus glue driver for Xilinx USB host controller. The controller can be
configured as HS only or HS/FS hybrid. The driver uses the device tree file
to configure the driver according to the setting in the hardware system.
This driver has been tested with usbtest using the NET2280 PCI card.
Signed-off-by: Julie Zhu <julie.zhu@xilinx.com>
Signed-off-by: John Linn <john.linn@xilinx.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Taken from socketcan-svn, fixed remaining todos, cleaned up, tested with a
phyCORE-MPC5200B-IO and a custom board.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the "fsl,wdt-on-boot" OF property as to reserve a GPT as WDT which may
be a requirement in safety-related (e.g. ISO/EN 61508) applications.
Signed-off-by: Albrecht Dreß <albrecht.dress@arcor.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds needed nodes and properties to support suspend/resume
on the MPC8610HPCD boards.
There is a dedicated switch (SW9) that is used to wake up the boards.
By default the SW9 button is routed to IRQ8, but could be re-routed
(via PIXIS) to sreset.
With 'no_console_suspend' kernel command line argument specified, the
board is also able to wakeup upon serial port input.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Scott Wood <scottwood@freescale.com> [dts]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
eSDHC block in MPC837x SOCs reports inverted write-protect state, soon
sdhci-of driver will look for sdhci,wp-inverted properties to decide
whether apply a specific quirk.
So, document the property and add it to device tree source files.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: David Vrabel <david.vrabel@csr.com>
Cc: Ben Dooks <ben@fluff.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use physmap_of to access RAMs as mtd and add documenation for it. This approach
is a lot less intrusive as adding an of-wrapper around plat-ram.c. As most
extensions of plat-ram.c (e.g. custom map-functions) can't be mapped to the
device tree anyhow, extending physmap_of seems to be the cleanest approach.
Tested with a phyCORE-MPC5121e.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Vitaly Wool <vwool@ru.mvista.com>
Cc: Artem Bityutskiy <dedekind@infradead.org>
Cc: Ken MacLeod <ken@bitsko.slc.ut.us>
Cc: Albrecht Dreß <albrecht.dress@arcor.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
There already is a "default-on" trigger but there are problems with it.
For one, it's a inefficient way to do it and requires led trigger support
to be compiled in.
But the real reason is that is produces a glitch on the LED. The GPIO is
allocate with the LED *off*, then *later* when the trigger runs it is
turned back on. If the LED was already on via the GPIO's reset default or
action of the firmware, this produces a glitch where the LED goes from on
to off to on. While normally this is fast enough that it wouldn't be
noticeable to a human observer, there are still serious problems.
One is that there may be something else on the GPIO line, like a hardware
alarm or watchdog, that is fast enough to notice the glitch.
Another is that the kernel may panic before the LED is turned back on, thus
hanging with the LED in the wrong state. This is not just speculation, but
actually happened to me with an embedded system that has an LED which
should turn off when the kernel finishes booting, which was left in the
incorrect state due to a bug in the OF LED binding code.
We also let GPIO LEDs get their initial value from whatever the current
state of the GPIO line is. On some systems the LEDs are put into some
state by the firmware or hardware before Linux boots, and it is desired to
have them keep this state which is otherwise unknown to Linux.
This requires that the underlying GPIO driver support reading the value of
output GPIOs. Some drivers support this and some do not.
The platform device binding gains a field in the platform data
"default_state" that controls this. There are three constants defined to
select from on, off, or keeping the current state. The OpenFirmware
binding uses a property named "default-state" that can be set to "on",
"off", or "keep". The default if the property isn't present is off.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
Split device tree binding out of booting-without-of.txt and put them
into their own files per binding.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some hosts (hardware configurations, or particular SD/MMC slots) may
not support 4-bit bus. For example, on MPC8569E-MDS boards we can
switch between serial (1-bit only) and nibble (4-bit) modes, thought
we have to disable more peripherals to work in 4-bit mode.
Along with some small core changes, this patch modifies sdhci-of
driver, so that now it looks for "sdhci,1-bit-only" property in the
device-tree, and if specified we enable a proper quirk.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
This patch adds a generic driver for SJA1000 chips on the OpenFirmware
platform bus found on embedded PowerPC systems. You need a SJA1000 node
definition in your flattened device tree source (DTS) file similar to:
can@3,100 {
compatible = "nxp,sja1000";
reg = <3 0x100 0x80>;
interrupts = <2 0>;
interrupt-parent = <&mpic>;
nxp,external-clock-frequency = <16000000>;
};
See also Documentation/powerpc/dts-bindings/can/sja1000.txt.
CC: devicetree-discuss@ozlabs.org
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Updated the binding spec to use "fsl,eshdc" as the base compatible
rather than the first chip in the family.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The latest QE chip may have more Serial Number(SNUM)s of thread to use. We
will get the number of SNUMs from device tree by reading the new property
"fsl,qe-num-snums", and set 28 as the default number of SNUMs so that it is
compatible with the old QE chips' device trees which don't have this new
property. The macro QE_NUM_OF_SNUM is defined as the maximum number in QE
snum table which is 256.
Also we update the snum_init[] array with 18 more new SNUMs which are
confirmed to be useful on new chip.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Change the RISC allocation to macros instead of enum, add function to read
the number of risc engines from the new property "fsl,qe-num-riscs" under
the qe node in dts. Add new property "fsl,qe-num-riscs" description in
qe.txt
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The first 4k region of CCSR space is well defined for local access
windows, CCSRBAR, etc. The second 4k region is well defined as
register for configuring and getting errors for the MPX coherency
module.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The first 4k region of CCSR space is well defined for local access
windows, CCSRBAR, etc. The second 4k region is well defined as
register for configuring and getting errors for the ECM coherency
module.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add binding for mtd nodes with multiple reg tuples. Multiple reg tuples
are used when the flash region covers multiple devices of the same type,
but not necessarily the same size.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
It's easier to find bindings descriptions in separate files. So factor
out the MTD physmap bindings into a separate file to not clutter
booting-without-of.txt more.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch documents the new bindings for the MPC I2C bus driver.
Furthermore, it removes obsolete FSL device related definitions
for I2C.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add bindings to support LEDs defined as of_platform devices in addition to
the existing bindings for platform devices.
New options in Kconfig allow the platform binding code and/or the
of_platform code to be turned on. The of_platform code is of course only
available on archs that have OF support.
The existing probe and remove methods are refactored to use new functions
create_gpio_led(), to create and register one led, and delete_gpio_led(),
to unregister and free one led. The new probe and remove methods for the
of_platform driver can then share most of the common probe and remove code
with the platform driver.
The suspend and resume methods aren't shared, but they are very short. The
actual led driving code is the same for LEDs created by either binding.
The OF bindings are based on patch by Anton Vorontsov
<avorontsov@ru.mvista.com>. They have been extended to allow multiple LEDs
per device.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
This patch adds documentation for the new NAND FSL UPM bindings for:
NAND: FSL-UPM: add multi chip support
NAND: FSL-UPM: Add wait flags to support board/chip specific delays
It also documents the old binding for "chip-delay".
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The bindings describes a case where MMC/SD/SDIO slot directly connected to
a SPI bus. Such setups are widely used on embedded PowerPC boards.
The patch also adds the mmc-spi-slot entry to the OpenFirmware modalias
table.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Anatolij Gustschin