V4L1 API is depreciated and should be removed soon from kernel. This patch
adds two new options, one to disable V4L1 drivers, and another to disable
V4L1 compat module. This way, it would be easy to check what still depends
on V4L1 stuff, allowing also to test if app works fine with V4L2 only support.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Spotted a couple more places where it fails to check if
dvb_register_adapter() fails.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Now that the CI code reinitialises the frontend, need to move the CI
initialisation to after the frontend init in order to ensure the frontend is
always in a good state. Fixes an oops caused by the frontend being NULL as
well.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
It turns out the firmware on the TT budget-ci 1.1 slots doesn't generate
interrupts. This patch adds support for this using polling mode on these
slots.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This mutex is meant to stop two devices getting the same ID. dvbdev_get_free_id()
scans the list of already allocated devices to find a free id.
Unfortunately, since the mutex is unlocked before the card is added to the
above list, it is still possible for two of them to get the same id.
Its debatable whether this mutex lock is actually needed, but I'm unwilling
to just remove it in case something does depend on it.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Unfortunately on the budget-av board, the CAM reset line is tied to the
frontend reset line, so resetting the CAM also zaps the frontend. This
breaks the tda1004x at least, and causes it to fail to tune until the
budget-av module is reloaded. This patch adds an exported function to dvb_frontend
that allows a card to forcibly reinitialise a frontend. The budget-av now
does this on CAM reset, which corrects this problem.
since they do not tie the CAM reset line to the frontend reset line.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The dvr device could be opened multiple times simultaneously in O_RDONLY mode.
Each open after the first would allocate a new dvr buffer (1880 KB) and leak
the old buffer. The first close would de-allocate the dvr buffer and cause
all other open dvrs to stop working. This patch allows only a single O_RDONLY
open of the drv device, as per the API specification. Multiple O_WRONLY opens
are still allowed and don't appear to cause any problems.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This attached patch was originally proposed by Anssi Hannula to the dvb-kernel
user to choose the default broadcast mode when using the ttpci driver.
NTSC users need to only add the following line to modprobe.d:
options dvb-ttpci tv_standard=1
PAL users will not need to change anything, for this will be the default.
Signed-off-by: C.Y.M <syphir@syphir.sytes.net>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch fixes a typo in a comment.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Issue a warning when more than 80% of the DMA buffer is being used
(probably due to bad IRQ latency). Warnings are rate-limited.
- Introduce a new parameter 'bufsize' (in KByte) which increases the
default DMA buffer of 188 KByte up to 1410 KByte (Activy: 564 KByte).
Signed-off-by: Ingo Schneider <mail@ingo-schneider.de>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There seems to be a new version of the USB DVB-T stick from WideView with a new demod-revision inside and thus a new firwmare.
This patch enables support for that.
Thanks to Mikel Martin for early testing.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Thanks to: Andrew Cohen <cohen@andy.bu.edu>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Added keycodes for the DViCO FusionHDTV portable remote control.
- Enabled the remote control for both versions of FusionHDTV DVB-T USB
and the FusionHDTV 5 USB Gold (ATSC)
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The bt8xx drivers uses request_firmware()
and thus needs to select FW_LOADER.
Signed-off-by: maximilian attems <maks@sternwelten.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Mark the f_ops members of inodes as const, as well as fix the
ripple-through this causes by places that copy this f_ops and then "do
stuff" with it.
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a new audio mode V4L2_TUNER_MODE_LANG1_LANG2 (used by VIDIOC_G/S_TUNER).
This mode allows the user to select both languages of a bilingual transmission,
one language on the left, one on the right audio channel. If there is no
bilingual transmission, or it is not supported, then this mode should act like
V4L2_TUNER_MODE_STEREO.
This mode is introduced for PVR-like drivers where it is useful to be able to
record both languages of a bilingual broadcast.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Only the Medion boxes return 0x08 after an i2c read/write.
The bluebird devices do not return anything at all.
This patch conditionalizes the test for the 0x08 return code
to produce a warning message when using the Medion box, only.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- corrects the wording in some of the debug messages.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Removed the FIXME comment from bluebird_patch_dvico_firmware_download:
/* FIXME: are we allowed to change the fw-data ? */
Yes, we are allowed. DViCO's Windows driver also does the same thing.
A single firmware image is used to support all of the bluebird boxes.
The firmware sets all devices to PID: d700. Instead of using that, the
driver replaces the d700 with the cold PID+1 before the download.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch removes the (harmless) -ETIMEDOUT during device init
for the DViCO FusionHDTV Bluebird boxes, by conditionalizing the
gpio write inside cxusb_i2c_xfer to happen only for Medion boxes.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There was no MODULE_DEVICE_TABLE for the b2c2-flexcop-usb module. This makes it
impossible for hotplug to load the module automatically, when such a device is
connected.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This reverts commit 08f1d0b99f
The "bt8xx/ conversion" for drivers/video/ hasn't actually percolated
all the way to this tree, so the Makefile change escaped too soon.
Build breakage noticed by Jeff Garzik <jeff@garzik.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add wss_cfg_4_3 and wss_cfg_16_9 configuration options.
Firmware 2623 or later required.
Both parameters are bit masks:
- bit 15: disable WSS
- bit 14: send short WSS burst, then turn off WSS
- bit 13..0: WSS bits as specified by the standard
These parameters are useful if you own a broken tv set which
does not handle wss correctly.
Default settings:
- wss_cfg_4_3: 0x4008
- wss_cfg_16_9: 0x0007
These should work with most devices.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Moved duplicated code of ALPS BSRU6 tuner to a standalone file.
Modified av7110 and budget drivers to include the new file.
Signed-off-by: Perceval Anichini <perceval.anichini@streamvision.fr>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Corrected typo for NxtWave NXT200X
- Added "Oren" manufacturer name to menu items for OR51132 and OR51211
- Removed "(pcHDTV HDx000 card)" from Oren frontends menu item names,
This isn't necessary, as these frontends are selected by the card drivers,
build configuration (DVB_BT8XX and VIDEO_CX88_DVB).
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Detaching the device didn't clean up several device files in /dev/dvb,
after applying that patch all dvb devices disappeared as expected.
Signed-off-by: Markus Rechberger <mrechberger@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Use dvb_ringbuffer instead of an own buffer implementation in
dmxdev.[ch].
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Oliver Endriss spotted, that resetting read and write pointers on
flush() requires additional locking and breaks the av7110 driver.
Therefore this patch partially reverts the previous patch titled "make
dvb_ringbuffer compatible to dmxdev_buffer".
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Added variable 'error' to struct dvb_ringbuffer, which is set to zero on
init() and flush(). Also reset read an write pointers to zero on flush()
to get less fragmented data.
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Used Lindent, manually changed some line breaks. Removed invalid email
addresses, useless casts and useless initialization of return values.
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Rename 'enum dmxdevype' to 'enum dmxdev_type' and use this enum instead
of int for the member 'type' of struct dmxdev_filter.
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The member dvbdev gets initialized once but is never used after that.
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The PID value is already stored in struct dmx_sct_filter_params which is
a member of struct dmxdev_filter.
Acked-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Typos grab bag of the month.
Eyeballed by jmc@ in OpenBSD.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Workaround for Nexus CA: Debi test fails unless first debi write is repeated.
Signed-off-by: Marco Schluessler <marco@lordzodiac.de>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Typos grab bag of the month.
Eyeballed by jmc@ in OpenBSD.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- The tuner used in DViCO FusionHDTV DVB-T hybrid is made by Thomson
- renamed tuner and dvb_pll structs accordingly
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support for the FE6600 tuner used on the DVB-T Hybrid board.
Add support for the Zarlink ZL10353 DVB-T demodulator, which supersedes the
MT352, used on the DViCO FusionHDTV DVB-T Hybrid and later model Plus boards.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Use refactored LNBP21/BSBE1 code for Technotrend/Hauppauge DVB-S rev 2.3.
As a side effect, FE_ENABLE_HIGH_LNB_VOLTAGE ioctl is supported now.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Moved duplicated code to separate files.
LNBP21 stuff rewritten from scratch, BSBE1 copied from av7110.c.
Modified budget driver to use the new routines.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Workaround for Nexus CA: Debi test fails unless first debi write is repeated.
Signed-off-by: Marco Schluessler <marco@lordzodiac.de>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Mauro Carvalho Chehab