The return of the omap4_cm_wait_module_ready function is checked
in order to avoid accessing the sysconfig register if the module is
not in the correct state.
In that case the _setup will exit without trying to reset
using sysconfig.
For the moment a warning is printed. A proper management of fclk
and module reset will have to be done in order to init correctly
the problematic IPs listed below.
<4>omap_hwmod: ivahd: cannot be enabled (3)
<4>omap_hwmod: iss: cannot be enabled (3)
<4>omap_hwmod: tesla: cannot be enabled (3)
<4>omap_hwmod: sdma: cannot be enabled (3)
<4>omap_hwmod: sl2: cannot be enabled (3)
<4>omap_hwmod: sad2d: cannot be enabled (3)
<4>omap_hwmod: ducati: cannot be enabled (3)
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The maximum timeout to wait for the PRCM to request that a module
exit idle or reach functionnal state is common to OMAP2/3/4 SoCs,
so, move it to the chip family-common cm.h include file.
Reduce the timeout from 20 ms to 2 ms.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Fix all of the remaining PRCM register shift/bitmask macros that did not
use the _SHIFT/_MASK suffixes to use them. This makes the use of these
macros consistent. It is intended to reduce error, as code can be inspected
visually by reviewers to ensure that bitshifts and bitmasks are used in
the appropriate places.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Current implementation defines clock idle state indicators based on the
cpu information (cpu_is_omap24xx() or cpu_is_omap34xx()) in a system wide
manner. This patch extends the find_idlest() function in clkops to pass
back the idle state indicator for that clock, thus allowing idle state
indicators to be defined on a per clock basis if required.
This is specifically needed on AM35xx devices as the new IPSS clocks
indicates the idle status (0 is idle, 1 is ready) in a way just
opposite to how its handled in OMAP3 (0 is ready, 1 is idle).
Signed-off-by: Ranjith Lohithakshan <ranjithl@ti.com>
[paul@pwsan.com: updated to apply after commit 98c45457 et seq.]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Here the ".clkstctrl_reg" field is added to the clockdomain stucture
as the module offsets for OMAP4 do not map one to one for powerdomains
and clockdomains as it used to for OMAP3. Hence we need to use absolute
addresses to access the control registers. Some of the clock domains have
modules falling in the address space of PRM partition. Hence necessitating
the use of absolute adresses.
Signed-off-by: Abhijit Pagare <abhijitpagare@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
This patch adds dummy hooks for OMAP4 dpll api's. Removes
dummy hooks for clkdev api's and enables CLKDEV
for OMAP4.
Also comments clockdomain calls from within the clock
framework as its not supported yet for OMAP4.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
This patch adds OMAP4 specific CM1 and CM2 module
register defs. Autogenerated using a python scripts
(gen_cm1_4430_h.py,gen_cm2_4430_h.py) developed
by Paul Walmsley and Benoit Cousson.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
This patch splits OMAP2_IO_ADDRESS to OMAP2_L3_IO_ADDRESS and
OMAP2_L4_IO_ADDRESS to reclaim more IO space.
The omap_read*() and omap_write*() functions will work only over
L4 address space. Current omap kernel stack uses these functions
only to access registers over L4 io address space
Note that these macros should only be used when ioremap does
not work. Please use ioremap instead in all new code.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
After a hardware module's clocks are enabled, Linux must wait for it
to indicate readiness via its IDLEST bit before attempting to access
the device, otherwise register accesses to the device may trigger an
abort. This has traditionally been implemented in the clock
framework, but this is the wrong place for it: the clock framework
doesn't know which module clocks must be enabled for a module to leave
idle; and if a module is not in smart-idle mode, it may never leave
idle at all. This type of information is best stored in a
per-hardware module data structure (coming in a following patch),
rather than a per-clock data structure. The new code will use these new
functions to handle waiting for modules to enable.
Once hardware module data is filled in for all of the on-chip devices,
the clock framework code to handle IDLEST waiting can be removed.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Search and replace OMAP_IO_ADDRESS with OMAP1_IO_ADDRESS and OMAP2_IO_ADDRESS,
and convert omap_read/write into a functions instead of a macros.
Also rename OMAP_MPUIO_VBASE to OMAP1_MPUIO_VBASE.
In the long run, most code should use ioremap + __raw_read/write instead.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove OMAP_PRM_REGADDR and use processor specific defines instead.
Also fold in a patch from Kevin Hilman to add _OFFSET #defines
for the PRCM registers to be used with the prm_[read|write]_* macros.
These are used extensively in the forthcoming OMAP PM support.
Also remove now unused OMAP2_PRM_BASE.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove OMAP_PRM_REGADDR and use processor specific defines instead.
Also fold in a patch from Kevin Hilman to add _OFFSET #defines
for the PRCM registers to be used with the prm_[read|write]_* macros.
These are used extensively in the forthcoming OMAP PM support.
Also remove now unused OMAP2_PRM_BASE.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP1_IO_ADDRESS(), OMAP2_IO_ADDRESS() and IO_ADDRESS() returns cookies
for use with __raw_{read|write}* for accessing registers. Therefore,
these macros should return (void __iomem *) cookies, not integer values.
Doing this improves typechecking, and means we can find those places
where, eg, DMA controllers are incorrectly given virtual addresses to
DMA to, or physical addresses are thrown through a virtual to physical
address translation.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds support for DPLL autoidle control to the OMAP3 clock
framework. These functions will be used by the noncore DPLL enable
and disable code - this is because, according to the CDP code, the
DPLL autoidle status must be saved and restored across DPLL
lock/bypass/off transitions.
N.B.: the CORE DPLL (DPLL3) has three autoidle mode options, rather
than just two. This code currently does not support the third option,
low-power bypass autoidle.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
New struct omap_globals contains the omap processor specific
module bases. Use omap_globals to set the various base addresses
to make detecting omap chip type simpler.
Also introduce OMAP1_IO_ADDRESS and OMAP2_IO_ADDRESS for future multi-omap
patches.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds common register access for 24xx and 34xx power
and clock management in order to share code between 24xx and 34xx.
Only change USB platform init code to use new register access, other
access will be changed in later patches.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Benoit Cousson