Note that the periodic work has to be started with initialized==1
Signed-off-by: Michael Buesch <mbuesch@freenet.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The proper fix for this is to move IRQ enabling to the end of
init_board. But this is nontrivial and needs to be done with care.
Stay with this cheap workaround for now.
Signed-off-by: Michael Buesch <mbuesch@freenet.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wireless Ext update:
update we_version_source
set enc_capa
Signed-off-by: Michael Buesch <mbuesch@freenet.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch contains the beginnings of ethtool support for bcm43xx.
It only implements get_drvinfo and get_link, but that's enough for
ifplugd to use ethtool to know whether we're associated or not and then
start or stop dhcp as necessary.
Signed-off-by: Jason Lunz <lunz@falooley.org>
Signed-off-by: Michael Buesch <mbuesch@freenet.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Geographical restriction should become part of the 80211 stack,
so every driver does not have to duplicate it.
Signed-off-by: Michael Buesch <mbuesch@freenet.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Import the bcm43xx driver from the upstream sources here:
ftp://ftp.berlios.de/pub/bcm43xx/snapshots/bcm43xx/bcm43xx-20060123.tar.bz2
Signed-off-by: John W. Linville <linville@tuxdriver.com>
By defining generic hweight*() routines
- hweight64() will be defined on all architectures
- hweight_long() will use architecture optimized hweight32() or hweight64()
I found two possible cleanups by these reasons.
Signed-off-by: Akinobu Mita <mita@miraclelinux.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Change all instances of EXPORT_SYMBOL() in the core EDAC module to
EXPORT_SYMBOL_GPL().
Signed-off-by: David S. Peterson <dsp@llnl.gov>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Dave Jiang <djiang@mvista.com>: Fix EDAC e752x driver so it
outputs sysbus-specific error message when sysbus error detected.
Signed-off-by: David S. Peterson <dsp@llnl.gov>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Cosmetic indentation/formatting cleanup for EDAC code. Make sure we
are using tabs rather than spaces to indent, etc.
Signed-off-by: David S. Peterson <dsp@llnl.gov>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix EDAC code so EXPORT_SYMBOL comes after the function that is being
exported. This is to maintain consistency with the rest of the kernel.
Signed-off-by: David S. Peterson <dsp@llnl.gov>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Add x86 dependency in drivers/edac/Kconfig for all current
platform-specific modules.
- Add PCI dependency to Radisys 82600 driver
Signed-off-by: David S. Peterson <dsp@llnl.gov>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Fix code so we always hold mem_ctls_mutex while we are stepping
through the list of mem_ctl_info structures. Otherwise bad things
may happen if one task is stepping through the list while another
task is modifying it. We may eventually want to use reference
counting to manage the mem_ctl_info structures. In the meantime we
may as well fix this bug.
- Don't disable interrupts while we are walking the list of
mem_ctl_info structures in check_mc_devices(). This is unnecessary.
Signed-off-by: David S. Peterson <dsp@llnl.gov>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- After we unregister a kobject, wait for our kobject release method
to call complete(). This causes us to wait until the kobject
reference count reaches 0. Otherwise, a task accessing the EDAC
sysfs interface can hold the reference count above 0 until after the
EDAC module has been unloaded. When the reference count finally
drops to 0, this will result in an attempt to call our release
method inside the EDAC module after the module has already been
unloaded.
This isn't the best fix, since a process can get stuck sleeping forever
uninterruptibly if the user does the following:
rmmod my_module < /sys/my_sysfs/file
I'll go back and implement a better fix later. However this should
be ok for now.
- Call edac_remove_sysfs_mci_device() from edac_mc_del_mc() rather
than from edac_mc_free(). Since edac_mc_add_mc() calls
edac_create_sysfs_mci_device(), edac_mc_del_mc() should call
edac_remove_sysfs_mci_device().
Signed-off-by: David S. Peterson <dsp@llnl.gov>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Remove calls to kobject_init(). These are unnecessary because
kobject_register() calls kobject_init().
- Remove extra calls to kobject_put(). When we call
kobject_unregister(), this releases our reference to the kobject.
The extra calls to kobject_put() may cause the reference count to
drop to 0 while a kobject is still in use.
Signed-off-by: David S. Peterson <dsp@llnl.gov>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is part 2 of a 2-part patch set.
Fix edac_mc_add_mc() so it cleans up properly if call to
edac_create_sysfs_mci_device() fails.
Signed-off-by: David S. Peterson <dsp@llnl.gov>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is part 1 of a 2-part patch set. The code changes are split into
two parts to make the patches more readable.
Move complete_mc_list_del() and del_mc_from_global_list() so we can
call del_mc_from_global_list() from edac_mc_add_mc() without forward
declarations. Perhaps using forward declarations would be better?
I'm doing things this way because the rest of the code is missing
them.
Signed-off-by: David S. Peterson <dsp@llnl.gov>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix xxx_probe1() functions so they call xxx_get_error_info() functions
to clear initial errors. This is simpler and cleaner than duplicating
the low-level code for accessing PCI config space.
Signed-off-by: David S. Peterson <dsp@llnl.gov>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix minor logic bug in e7xxx_remove_one().
Signed-off-by: David S. Peterson <dsp@llnl.gov>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Fix i82875p_probe1() so it calls pci_get_device() instead of
pci_find_device().
- Fix i82875p_probe1() so it cleans up properly on failure.
- Fix i82875p_init() so it cleans up properly on failure.
Signed-off-by: David S. Peterson <dsp@llnl.gov>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Fix i82860_init() so it cleans up properly on failure.
- Fix i82860_exit() so it cleans up properly.
- Fix typo in comment (i.e. www.redhat.com.com).
Signed-off-by: David S. Peterson <dsp@llnl.gov>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Add ctl_dev field to "struct e752x_dev_info". Then we can eliminate
ugly switch statement from e752x_probe1().
- Remove code from e752x_probe1() that clears initial PCI bus parity
errors. The core EDAC module already does this.
Signed-off-by: David S. Peterson <dsp@llnl.gov>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Michael Buesch