Struct i2c_client_address_data only contains one field at this point,
which makes its usefulness questionable. Get rid of it and pass simple
address lists around instead.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Initially only for 34xx. This code allows us to:
- Make the code more generic as the omap internal signal
names can stay the same across omap generations for some
devices
- Map mux registers to GPIO registers that is needed for
dynamic muxing of pins during off-idle
- Override bootloader mux values via kernel cmdline using
omap_mux=some.signa1=0x1234,some.signal2=0x1234
- View and set the mux registers via debugfs if
CONFIG_DEBUG_FS is enabled
Cc: Mike Rapoport <mike@compulab.co.il>
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
A small addition to the ldisc method descriptions.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ESP driver has been marked broken for years. It's an old ISA device
that clearly nobody cares about any more. Remove it
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Accroding commit 0994375e, which is adding remove_id sysfs attr
for pci drivers, for management tools dynamically bind/unbind
a pci/usb devices to a specified drivers; with this patch,
the management tools can be simplied.
And the original code didn't handle the failure of
usb_create_newid_file, fixed in this patch.
Signed-off-by: CHENG Renquan <rqcheng@smu.edu.sg>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1311) fixes a problem in usb-storage: Some devices are
pretty broken when it comes to reporting sense data. The information
they send back indicates that they have more than 18 bytes of sense
data available, but when the system asks for more than 18 they fail or
hang. The symptom is that probing fails with multiple resets.
The patch adds a new BAD_SENSE flag to indicate that usb-storage
should never ask for more than 18 bytes of sense data. The flag can
be set in an unusual_devs entry or via the "quirks=" module parameter,
and it is set automatically whenever a REQUEST SENSE command for more
than 18 bytes fails or times out.
An unusual_devs entry is added for the Agfa photo frame, which uses a
Prolific chip having this bug.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Daniel Kukula <daniel.kuku@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1303) revises the USB Power Management infrastructure to
make it compatible with the new driver-model Runtime PM framework:
Drivers are no longer allowed to access intf->pm_usage_cnt
directly; the PM framework manages its own usage counters.
usb_autopm_set_interface() is eliminated, because it directly
sets intf->pm_usage_cnt.
usb_autopm_enable() and usb_autopm_disable() are eliminated,
because they call usb_autopm_set_interface().
usb_autopm_get_interface_no_resume() and
usb_autopm_put_interface_no_suspend() are added. They
correspond to pm_runtime_get_noresume() and
pm_runtime_put_noidle() in the PM framework.
The power/level attribute no longer accepts "suspend", only
"on" and "auto". The PM framework doesn't allow devices to be
forced into a suspended mode.
The hub driver contains the only code that violates the new
guidelines. It is updated to use the new interface routines instead.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1302) removes the auto_pm flag from struct usb_device.
The flag's only purpose was to distinguish between autosuspends and
external suspends, but that information is now available in the
pm_message_t argument passed to suspend methods.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add the wusb_phy_rate sysfs file to Wireless USB host controllers. This
sets the maximum PHY rate that will be used for all connected devices.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add bus glue driver for Xilinx USB host controller. The controller can be
configured as HS only or HS/FS hybrid. The driver uses the device tree file
to configure the driver according to the setting in the hardware system.
This driver has been tested with usbtest using the NET2280 PCI card.
Signed-off-by: Julie Zhu <julie.zhu@xilinx.com>
Signed-off-by: John Linn <john.linn@xilinx.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Users on the list recently complained about differences across
filesystems w.r.t. how to mount without a journal replay.
In the discussion it was noted that xfs's "norecovery" option is
perhaps more descriptively accurate than "noload," so let's make
that an alias for ext3.
Also show this status in /proc/mounts
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Jan Kara <jack@suse.cz>
All callers really want the more logical filemap_fdatawait_range interface,
so convert them to use it and merge wait_on_page_writeback_range into
filemap_fdatawait_range.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
Add exofs.txt to filesystems Documentation index and fix some typos,
identation and grammar.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
We have a directory for misc drivers documentation, let's use it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
Cc: Rodolfo Giometti <giometti@linux.it>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
the description in Documentation/filesystems/proc.txt of the
procs_running entry in /proc/stat is confusing (according to that
description, it looks as if procs_running could only be a number
between 0 and the number of CPUs).
Changed it to a more accurate description in the patch attached.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since signal_pending() takes a task_struct pointer as an argument, update
the example to pass in 'current'.
Signed-off-by: Shawn Bohrer <shawn.bohrer@gmail.com>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use DMA_BIT_MASK(24) instead of 0x00ffffff in DMA-mapping.txt
Signed-off-by: Marin Mitov <mitov@issp.bas.bg>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The ADT7476 has 5 dedicated pins for VID input, and the +12V input can
optionally be used as a 6th VID pin. Add support for VID input.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
Add support for the Analog Devices ADT7476 chip. This chip is largely
compatible with the ADT7473 and ADT7475, with additional features.
In particular, it has 5 voltage inputs instead of 2, and VID input
pins.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
Add support for the Analog Devices ADT7490 chip. This chip is largely
compatible with the ADT7473 and ADT7475, with additional features.
In particular, it has 6 voltage inputs instead of 2.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
New documentation for the adt7475 driver, based on the adt7473 driver
documentation. It is IMHO much more useful that the previous
documentation which was essentially redundant with sysfs-interface.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
Add support for the ADT7473 to the adt7475 driver, and mark the
adt7473 driver for removal. The ADT7473 and ADT7475 chips are almost
the same chip and essentially compatible, so there's no point in
having separate drivers for them.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
This adds support for the Fintek f71889fg to the f71882fg driver,
many thanks to Gerd v. Egidy for providing (remote) access to a
machine which such an ic.
Note that this bit of the patch:
- val = SENSORS_LIMIT(val, 0, 255);
+
+ if (data->type == f71889fg)
+ val = SENSORS_LIMIT(val, -128, 127);
+ else
+ val = SENSORS_LIMIT(val, 0, 127);
Changes behaviour for already supported models, the new behaviour is correct
as the already supported models have bit 7 of the involved registers fixed at
0, so the previous behaviour which allowed setting temp zone limits > 127
was not correct.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This driver provides support for the ADC integrated into the
Freescale MC13783 PMIC.
Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This module parameter is there to workaround broken BIOS. I'm not even
sure if it was used in the past 5 years, and it gets in the way of
converting the driver to the MFD infrastructure. So tell the users how
they can do the same from user-space.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Rodolfo Giometti <giometti@linux.it>
The VID input pins can alternatively be used as GPIOs. Make sure we
have at least 4 pins used for VID, otherwise don't bother reading and
exposing VID.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Adam Nielsen <a.nielsen@shikadi.net>
Document the case of hybrid automatic fan speed control
implementations, where trip points are associated to both PWM output
channels and temperature input channels.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Just to save some time, add direct git link to grub hda-analyzer
Signed-off-by: Alexey Fisher <bug-track@fisher-privat.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Version 3 of this patch is updated with documentation added to
Documentation/ABI. There are no changes to any of the C code from v2
of the patch.
In order to support kernel DLPAR of CPU resources we need to provide an
interface to add (probe) and remove (release) the resource from the system.
This patch Creates new generic probe and release sysfs files to facilitate
cpu probe/release. The probe/release interface provides for allowing each
arch to supply their own routines for implementing the backend of adding
and removing cpus to/from the system.
This also creates the powerpc specific stubs to handle the arch callouts
from writes to the sysfs files.
The creation and use of these files is regulated by the
CONFIG_ARCH_CPU_PROBE_RELEASE option so that only architectures that need the
capability will have the files created.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Various additions and improvements to the Gigaset driver's README
file, and added comments to its userspace visible include file.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is an updated patch for the Apple iMac 9,1 model to add sound.
Original patch posted here:
http://article.gmane.org/gmane.linux.alsa.devel/61361/match=
I have been using this patch for a while now
and have to say it works vary well, except for a few minor
things:
With the iMac 24-inch 3.06GHz Intel Core 2 Duo
everything seems to be working as it should,
although I have not looked into the microphone
(never really use one, nor have any apps to test,
my guess is it doesn't work, or I never figured out how
to get it to work).
With the iMac 24-inch 2.66GHz Intel Core 2 Duo
everything is the same as with the above machine
except I'm hearing a light scratchy/distortion noise
come out of the speakers when using headphones(above machine
does not do this).
Other than that the sound level is great(especially with good Dj headphones).
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Tested-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
More and more devices choose to reimplement support for sparse keymaps
first introduced by wistron driver. Move it into a library module so it
can be easily used by interested parties.
Reviewed-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add a module parameter to override the functionality bitfield. This
lets the user disable some commands. This can be used to force a chip
driver to take different code paths.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The legacy probe and force module parameters are obsolete now, the
same can be achieved using the new_device sysfs interface, which is
both more flexible and cheaper (it is implemented by i2c-core rather
than replicated in every driver module.)
The legacy ignore module parameters can be dropped as well. Ignoring
can be done by instantiating a "dummy" device at the problematic
address.
This is the first step of a huge cleanup to i2c-core's i2c_detect
function, i2c.h's I2C_CLIENT_INSMOD* macros, and all drivers that made
use of them.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Superseded by tdfxfb. I2C/DDC support used to live in a separate
driver but this caused driver conflicts.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
Apparently, there are devices that can wake up the system from sleep
states and yet are incapable of generating wake-up events at run
time. Thus, introduce a flag indicating if given device is capable
of generating run-time wake-up events.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Currently the ->runtime_idle() callback is documented as having no
return value, but in fact it returns int. Although its return value
is ignored at the PM core level, it may be used by bus type routines
executing the drivers' ->runtime_idle() callbacks.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Add usage info to Documentation/lockstat.txt
Signed-off-by: Frank Rowand <frank.rowand@am.sony.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <4B05BE7D.30500@am.sony.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Adds support to VC211A em2800 card. As this board doesn't have eeprom,
and uses a common set of i2c address, it has no way to add any
autodetection for it.
The patch were tested by me and by Raimundo on his board. Thanks to
those tests, several bugs related to em2800 support were corrected.
for producing the usbsnoop dump, used to get the gpio's and allowing me
to remotelly access his machine and to the needed tests.
Thanks-to: Raimundo Eduvirgnes de Oliveira <eduvirgens@yahoo.com.br>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After excluding .h.xml from the whitespace to tab conversion I had to
regenerate this xml file. The only changes here are whitespace changes.
If we change videodev2.h in the future, then videodev2.h.xml will only
show that same change and no more unrelated whitespace changes.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It was really confusing to have media-specs, v4l2-spec and dvb-spec.
So this patch removes v4l2-spec and dvb-spec. The docs in dvb-spec and
the V4L1_API.html file were moved to media-specs/old-docs.
Removed all references to v4l2-spec and dvb-spec.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jean Delvare