Hardware resources should not be made available to other devices while
the network device is still registered. Also remove the related debug
statements.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Running Linux 2.6.17-rc3-mm1 which has this patch included I get this
interesting message:
airo(eth0): WPA unsupported (only firmware versions 5.30.17 and greater
support WPA. Detected 5.30.17)
airo_test_wpa_capable assumes that the softSubVer part of the firmware
version number is coded in BCD. Apparently, that's not true.
I have firmware version 5.30.17 and cap_rid.softSubVer is 0x11==17.
Signed-off-by: Michal Schmidt <xschmi00@stud.feec.vutbr.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix the conditions under which we poke at the APHY registers in
bcm43xx_phy_initg() to avoid a machine check on chips where they don't
exist.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The problem here is that the bcm34xx driver and the ieee80211
stack do not agree on what channels are possible for 802.11a.
The ieee80211 stack only wants channels between 34 and 165, while
the bcm43xx driver accepts anything from 0 to 200. I made the
bcm43xx driver comply with the ieee80211 stack expectations, by
using the proper constants.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
[mb]: Reduce stack usage by kzalloc-ing ieee80211_geo
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check for valid MAC address in SPROM fields instead of relying on
PHY type while setting the MAC address in the networking subsystem,
as some devices have multiple PHYs.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a crash when
iwconfig ethX mode foo
is done before
ifconfig ethX up
or after
ifconfig ethX down
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes the issues with multiple irqs.
I am resending based on feedback. I decoupled the dma mask for
consistent memory and fixed leak with multiple irq in error path.
Thanks to Manfred for catching the spin lock problem.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Fixes Rhine I cards disclosing fragments of previously transmitted frames
in new transmissions.
Before transmission, any socket buffer (skb) shorter than the ethernet
minimum length of 60 bytes was zero-padded. On Rhine I cards the data can
later be copied into an aligned transmission buffer without copying this
padding. This resulted in the transmission of the frame with the extra
bytes beyond the provided content leaking the previous contents of this
buffer on to the network.
Now zero-padding is repeated in the local aligned buffer if one is used.
Following a suggestion from the via-rhine maintainer, no attempt is made
here to avoid the duplicated effort of padding the skb if it is known that
an aligned buffer will definitely be used. This is to make the change
"obviously correct" and allow it to be applied to a stable kernel if
necessary. There is no change to the flow of control and the changes are
only to the Rhine I code path.
The patch has run on an in-service Rhine-I host without incident. Frames
shorter than 60 bytes are now correctly zero-padded when captured on a
separate host. I see no unusual stats reported by ifconfig, and no unusual
log messages.
Signed-off-by: Craig Brind <craigbrind@gmail.com>
Signed-off-by: Roger Luethi <rl@hellgate.ch>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
On Sat, Mar 11, Olaf Hering wrote:
> Why is the /sys/class/net/eth0/device symlink not created for the
> mv643xx_eth driver? Does this work for other platform device drivers?
> Seems to work for the ps2 keyboard at least.
The SET_NETDEV_DEV has to be done before a call to register_netdev. With
the new patch below, the device symlink for the platform device was
created. Unfortunately, after the 4 ls commands, the network connection
died. No idea if the box crashed or if something else broke, lost remote
access.
Provide sysfs 'device' in /class/net/ethN Also, set module owner field,
like pcnet32 driver does.
Signed-off-by: Olaf Hering <olh@suse.de>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Hi,
The following patch contains fix related to init and shutdown of adapter
as per user guide. The list of changes include
1. shutdown gracefully.
2. Need to mask/unmask interrupts in ISR required fro Xframe-E
3. Tx FIFO should be enabled after WRR calender programming
Signed-off-by: Ananda Raju <ananda.raju@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Hi,
This patch contains additional statistics counters added to s2io driver
these statistics are very much usefull in debugging the driver.
Signed-off-by: Ananda Raju <ananda.raju@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Hi,
This patch contains some of the bug fixes done for S2io driver.
Following are the brief description of changes
1. Continuing with initialization if we get minimum required MSI-X vectors
2. fix for ethtool online link test fails
3. make wait_for_cmd_complete generic for all command status registers
4. Print "Device is on PCI-E bus" for Xframe-E card
5. CX4 requires additional delay after sw_reset, and requires higher value for igp
6. Fixed panic due to non-TCP and/or LLC/SNAP traffic in case of lro
7. remove legacy code for old transponder
8. SPECIAL_REG_WRITE made to use 32-bit writes irrespective of system type
9. handle link interrupt as per user guide for Xframe II
10. Wait till all interrupts hndled
Signed-off-by: Ananda Raju <ananda.raju@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
hi,
This patch contains the modification and bug fixes with respect to
input parameters and outupt dmesages. following is brief description
of the changes.
1. Set default values for rx_ring_sz[0..7] and tx_fifo_len[0..7]
2. verify few basic load parameters
3. read product description from VPD
4. clean up of dmesg when driver is loaded
Signed-off-by: Ananda Raju <ananda.raju@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
hi,
This patch contains all the changes that were done to improve
performance of s2io driver. one line description of the changes
are
1. For Non NAPI case the rx interrupt handler is being called
unconditionally
2. code optimization and adding prefetch skb->data
3. Remove modulo operations in fast path
4. Enable Group Reads and set backoff interval to 0x1000
5. correct PIC_CNTL_SHARED_SPLITS macro definition, and reduce
pause parameter
6. Corrected logic of identifying rx buffer level in rx_buffer_level()
7. fix DMA map and unmap done with different sizes in 1-buf mode
8. Removed forcible disabling of ERO
9. Send up the packets with transfer code = 0x5
Signed-off-by: Ananda Raju <ananda.raju@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix bug in nvram write function. If the starting nvram address offset
happens to be the last dword of the page, the NVRAM_CMD_LAST bit will
not get set in the existing code. This patch fixes the bug by changing
the "else if" to "if" so that the last dword condition always gets
checked.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a reset_phy parameter to tg3_reset_hw() and tg3_init_hw(). With
the full chip reset during MAC address change, the automatic PHY reset
during chip reset will cause a link down and bonding will not work
properly as a result. With this reset_phy parameter, we can do a chip
reset without link down when changing MAC address or MTU.
Signed-off-by: Gary Zambrano <zambrano@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do the full chip reset when changing MAC address if ASF is enabled.
ASF sometimes uses a different MAC address than the driver. Without
the reset, the ASF MAC address may be overwritten when the driver's
MAC address is changed.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add some PHY workaround code to reduce jitter on some PHYs.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add netif_carrier_off() call during tg3_phy_reset(). This is needed
to properly track the netif_carrier state in cases where we do a
PHY reset with interrupts disabled. The SerDes code will not run
properly if the netif_carrier state is wrong.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the nic initialization. If the nic was in low power
mode, it brings it back to normal power. Also, it utilizes a new
hardware reset during the init.
I am resending based on feedback, I corrected the register size mapping
and delay after posted write.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The sky2_reset function only called from sky2_probe.
Maybe the compiler was smart enough to figure this out already.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The ALIGN() macro in kernel.h does the same math that the
sky2 driver was using for padding.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add an fake NAPI schedule once a second. This is an attempt to work around
for broken configurations with edge-triggered interrupts.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This is a workaround for the case edge-triggered irq's. Several users
seem to have broken configurations sharing edge-triggered irq's. To avoid
losing IRQ's, reshedule if more work arrives.
The changes to netdevice.h are to extract the part that puts device
back in list into separate inline.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update skb with the real packet size.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
airo cards with firmware versions of 5.30.17 and higher support WPA.
This patch recognizes WPA-capable firmware versions and adds support for
retrieving the WPA and RSN information elements from the card's scan
results. The JOB and FLAG fields are now independent, since there was
no space left in the FLAG field for FLAG_WPA_CAPABLE.
Signed-off-by: matthieu castet <castet.matthieu@free.fr>
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The new ipw2200 scan completion event feature will cause a potential event
race condition in wpa_supplicant. The patch fixes this problem by move the
ipw_disassociate() to the IW_AUTH_WPA_ENABLED event handling code.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
priv->last_noise is not used with the exponential averaging algorithm
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Makefile both IPW2200_RADIOTAP and IPW2200_PROMISCUOUS depend on
IPW2200_MONITOR. Let IPW2200_PROMISCUOUS select IPW2200_RADIOTAP.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Added version string fields so the version string indicates what is
configured (ie, you'll see 1.1.1kpmd if you are using a GIT snapshot
(Kernel.. previously -git), promiscuous (p), monitor (m), debug (d) build.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With this patch, a new promiscuous mode is enabled. If the module is loaded
with the rtap_iface=1 module parameter, two interfaces will be created
(instead of just one).
The second interface is prefixed 'rtap' and provides received 802.11 frames
on the current channel to user space in a radiotap header format.
Example usage:
% modprobe ipw2200 rtap_iface=1
% iwconfig eth1 essid MyNetwork
% dhcpcd eth1
% tcpdump -i rtap0
If you do not specify 'rtap_iface=1' then the rtap interface will
not be created and you will need to turn it on via:
% echo 1 > /sys/bus/pci/drivers/ipw2200/*/rtap_iface
You can filter out what type of information is passed to user space via
the rtap_filter sysfs entry. Currently you can tell the driver to
transmit just the headers (which will provide the RADIOTAP and IEEE
802.11 header but not the payload), to filter based on frame control
type (Management, Control, or Data), and whether to report transmitted
frames, received frames, or both.
The transmit frame reporting is based on a patch by Stefan Rompf.
Filters can be get and set via a sysfs interface. For example, set the
filter to only send headers (0x7), don't report Tx'd frames (0x10), and
don't report data frames (0x100):
% echo 0x117 > /sys/bus/pci/drivers/ipw2200/*/rtap_filter
All your packets are belong to us:
% tethereal -n -i rtap0
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch corrects endian issues with the v3.0 fw image format.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch make ipw2200 generate the scan event every time a scan has
completed, so that user space know when to get fresh results.
Dan Williams would like to go towards this model in Network Manager
rather than having to poll.
Signed-off-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch works with the ieee80211 stack to set the correct QoS bit to the
ipw2200 card. It fixed the TX failure problem for using WPA with QoS.
Signed-off-by: Hong Liu <hong.liu@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch replaces sliding averaging by exponential averaging for
reporting the wireless statistics for signal and noise level for ipw2200.
See details from: http://www.ces.clemson.edu/linux/ipw2200_averages.shtml
Signed-off-by: Bill Moss <bmoss@clemson.edu>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make all Orinoco PCI drivers (orinoco_pci, orinoco_plx, orinoco_tmd and
orinoco_nortel) as similar as possible. Use the best implementation of
error handling, the best error messages, the best comments.
Put common code to orinoco_pci.h. For now, it's suspend and resume
functions and function for registering the network device.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pavel Roskin