This patch adds driver for Sigmatek DVB-110 USB DVB-T stick. Stick has based
on hardware of Qtuantek QT1010 tuner, Zarlink ZL10353 (Intel CE 6353)
demodulator and Alcor Micro AU6610 DVB-T USB controller. HW is rather similar
as used in MSI Megasky GL861.
Currently, the driver works only in USB 2.0. In my understanding USB 1.1 is
also supported by hw but I cannot test it due to lack of USB 1.1 port. Device
supports only isochronous mode transfers. There is also eeprom in usb
controller(at least in address range 0x80 - 0xbf) for storing data, eg.
firmware. Anyway, firmware loading is not used / required by the device.
There seems to be at least one unknown I2C device in address 0xa0, probably
remote control or GPIO. Windows drivers reads registers from 0x00 to 0x07
from this unknown address.
Driver is based on gl861 module. Tuner has a lot of problems to lock with
megasky qt1010 module with this hardware with some broadcasting standards.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds support for MSI Mega Sky 580 / GL861 DVB-T USB2.0
Except for the 2 lines added to zl10353.c, zl10353_reset_attach needs
to be changed. If I read the code correctly setting parallel_ts will
take care of the 3rd byte, but the 2nd byte needs to be 0x0b instead
of 0x03 too. I guess these changes needs to be done only for this
device, not sure how to do that.
The zl10353 changes have been split apart from this patch, into the next
patch, soon to follow.
Signed-off-by: Carl Lundqvist <comabug@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Currently, the driver works in bulk mode supporting both USB 2.0 and
1.0 with and without hardware pid filters.
The ULi m9205 also supports isochronous transfer mode, but I have
dropped support for it because it depends on firmware and does not work
on all USB host chips. Further, I have no firmware with remote
controller support for this mode.
Signed-off-by: Aapo Tahkola <aet@rasterburn.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The vendor IDs in this file were all in alphabetical
order except for this one.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add alternative device ID (0xb808) for AverMedia AverTV Volar dongles.
Signed-off-by: Jose Carlos Garcia Sogo <jsogo@debian.org>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Added support for Nova-T Stick with USB-pid: 0x7060
Signed-off-by: Stefan Traby <stefan@hello-penguin.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds support for the new, STK7700-based revision
of the Leadtek Winfast DTV Dongle.
Signed-off-by: Michal CIJOML Semler <cijoml@volny.cz>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
First working version of the dib7000m-driver.
This commit also makes the Hauppauge NOVA-T Stick working.
Signed-off-by: Francois Kanounnikoff <fkanounnikoff@dibcom.fr>
Signed-off-by: Patrick Boettcher <pboettcher@dibcom.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support for DViCO FusionHDTV DVB-T Dual Digital 2 USB, which
is identical to the usb portion of DViCO FusionHDTV DVB-T Dual Digital 1.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Adding another USB product ID for the Nova-T 500. Reported by Jose Alberto Reguero.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This changeset finalizes the support of the Hauppauge Nova-T 500 (Dual DVB-T).
It adds correct AGC setting for the 3000P, correct firmware download state
detection.
Additionally it fixes the mt2060-driver to be able to be used with dvb_attach.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Changed the attach-function of the dib3000mc-driver to return only one
frontend. In case of multiple dib3000-chips on one board, one has to call the
i2c-enumeration manually before.
Added a field to Microtune 2060 config to output the clock to other
tuners/device on a board.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
After some structural changes, here comes the updated patch for the Club 3D
zap250mini USB dvb device.
Adding support for a WideView-based device with a different "COLD" ID.
Signed-off-by: Jochen Issing <jochen.issing@isign-softart.de>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Adding the USB ids for the LeadTek clone of the STK3000P-ref-design.
Signed-off-by: Olivier DANET <odanet@caramail.com>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Adding the USB IDs to dibusb-mc.c for the Artec T14 USB Stick based on STK3000P reference design.
Thanks to Thomas Rabe testing.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- some coding style fixes for newly added mt2060
- moved agc-config from fixed values in dib3000mc to configurable ones
- whitespace clean-ups for usb-id-file
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- MT2060 tuner driver
- Added support for some USB DVB-T devices based on Dib3000P
Signed-off-by: Olivier DANET <odanet@caramail.com>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Ok, here is the working patch for the Freecom DVB-T stick with USB-ID
14aa:0225.
It uses the Firmware-file, wich Erich Focht created and wich can be obtainded
from http://home.arcor.de/efocht/dvb-usb-wt220u-fc03.fw
Also the original patch is from Erich. It adds the proper USB-IDs and I only
had to change the endpoint of the MPEG-2 data-transfer to 0x86.
Signed-off-by: Alexander Tuschen <atuschen@web.de>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This is a patch which includes support for the GENPIX 8PSK->USB module. The
board supports QPSK, BPSK and 8PSK decoding (though I don't think it will be
DVB-S2 compliant) With the following patch, the boad is equivalent to a budget
card (no CA Module)
The patch which adds 8psk suppot will follow, but is seperate, as it requires
DVB-S2 support
More info on the board can be found at www.genpix-electronics.com (and they
host the requisite firmwares there as well)
Signed off by: Alan Nisota <alannisota@gmail.com>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There seems to be a new version of the USB DVB-T stick from WideView with a new demod-revision inside and thus a new firwmare.
This patch enables support for that.
Thanks to Mikel Martin for early testing.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Added USB ID for DigitalNow DVB-T Dual USB,
DViCO FusionHDTV DVB-T Dual USB clone
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Add support for the USB portion of the DViCO Dual Digital board.
Patch correct "warm" USB IDs into bluebird firmware before download.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Adds Bluebird ATSC support to the cxusb driver,
using dvb-usb-bluebird-atsc-01.fw firmware.
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Adding support for the Artec T1 USB2.0 box (real USB2.0)
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Cc: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Change the init call to optionally return the new dvb_usb_device directly.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add USB IDs of the Kworld Xpert DVB-T USB2.0 (clone of the ADStech box).
Thanks to Marcus Hagn for testing.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add driver for the TwinhanDTV StarBox and clones.
Thanks to Ralph Metzler for his initial work on this box and thanks to Twinhan
for their support.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support and rewrote some parts with the help of vendor information
(Thanks to Steve Chang from WideView, Inc.):
o added support for the WT-220U (Pensize DVB-T receiver)
o corrected byte order for unc,ber and the pid filter
o corrected number of pids that can be fetched at the same time.
o added some comments in Kconfig-file
o added USB IDs for the WT-220U
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
o Steve Chang reported the real name behind 0x14aa: WideView,
changed USB IDs accordingly.
o fixed an assignment
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add another USB ID pair for the VideoWalker USB DVB-T.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add preliminary support for the Medion Hybrid USB2.0 DVB-T/Analogue box.
Analogue part is not working yet (cx25842 --> ivtv?).
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add generalized dvb-usb driver which supports a wide variety of devices.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Antti Palosaari