Some sysfs problems reported. The serial number on late model
controllers was truncated. Non-DASD devices (tapes and CDROMs) were
showing up as JBOD in the level report on the physical channel.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The Adapter's Ignore Reset flag and insmod parameter boolean polarity
is incorrect in the driver.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Added support for MSI utilizing the aacraid.msi=1 parameter. This
patch adds some localized or like-minded janitor fixes. Since the
default is disabled, there is no impact on the code paths unless the
customer wishes to experiment with the MSI performance.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Luben Tuikov [mailto:ltuikov@yahoo.com] sez:
> Just as in your case and Tony's case, which I presume
> uses the same RAID firmware vendor, it would've
> probably been better if the RAID firmware vendor
> fixed the firmware to not set the VALID bit if the
> INFORMATION field is not valid.
Point taken regarding the aacraid driver. Dropped the VALID bit, and
then did some cleanup/simplification of the set_sense procedure and
the associated parameters. Mike did some preliminary tests when the
VALID bit was dropped before the 'Re: [PATCH] [SCSI] sd: make error
handling more robust' patches came on the scene. The change in the
SCSI subsystem does make this enclosed aacraid patch unnecessary, so
this aacraid patch is merely post battle ground cleanup. If the
simplification is an issue, repugnant, too much for a back-port to the
stable trees or clouds the point, this patch could be happily
distilled down to:
diff -ru a/drivers/scsi/aacraid/aachba.c b/drivers/scsi/aacraid/aachba.c
--- a/drivers/scsi/aacraid/aachba.c 2008-02-06 16:26:45.834938955 -0500
+++ b/drivers/scsi/aacraid/aachba.c 2008-02-06 16:32:01.109035329 -0500
@@ -865,7 +865,7 @@
u32 residue)
{
- sense_buf[0] = 0xF0; /* Sense data valid, err code 70h (current error) */
+ sense_buf[0] = 0x70; /* Sense data invalid, err code 70h (current error) */
sense_buf[1] = 0; /* Segment number, always zero */
if (incorrect_length) {
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch ensures that the modern adapters get a maximum sg segment
size on par with the maximum transfer size. Added some localized
janitor fixes to the discussion patch I used with Fujita.
FUJITA Tomonori [mailto:fujita.tomonori@lab.ntt.co.jp] sez:
> I think that setting the proper maximum segment size for the late
> model cards (as you did above) makes sense.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The first patch (a119ee8ee3) was a bit
too aggressive and nested the locks (!) unit testing was in
error. This patch was reverted by
203a512f09.
This new patch should fix the locks correctly.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This sets the segment size limit properly via pci_set_dma_max_seg_size
and remove blk_queue_max_segment_size because scsi-ml calls it.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Acked-by: "Salyzyn, Mark" <mark_salyzyn@adaptec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With the sg table code, every SCSI driver is now either chain capable
or broken (or has sg_tablesize set so chaining is never activated), so
there's no need to have a check in the host template.
Also tidy up the code by moving the scatterlist size defines into the
SCSI includes and permit the last entry of the scatterlist pools not
to be a power of two.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Alan noticed the lack of locking surrounding the driver's dealings
with the fib context managed by the trio of ioctls that are used by
the RAID management applications to retrieve Adapter Initiated FIBs. I
merely expanded the fib lock to include the fib context. There have
been no field reports of any issues generally because the applications
are relatively static and do not come and go often enough to stress
this area. I bloated this patch a little with some space junk.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The cards being added are supported in a limited sense already through
family matching, but we needed to add some functionality to the driver
to expose selectively the physical drives. These Physical drives are
specifically marked to not be part of any array and thus are declared
JBODs (Just a Bunch Of Drives) for generic SCSI access.
We report that this is the second patch in a set of two, but merely
depends on the stand-alone functionality of the first patch which adds
in that case the ability to report a driver feature flag via sysfs. We
leverage that functionality by reporting that this driver now supports
this new JBOD feature for the controller so that the array management
applications may react accordingly and guide the user as they manage
the controller.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Feature enhancement, adding a 'flags' entry that will reside in the
host controller's tree, with a newline separated list of arbitrary
ascii named features that indicate whether the combination of driver
and controller has support for said feature. Breaking from the
one-line output typical of sysfs entries, newline was added to tailor
for grep, or simple gets line by line string match within an
application. I added one for a compiler time check for existence of
debug print output, one for an optional manifest defined enhanced
status reporting in the logs, and one for runtime reporting whether
the controller and driver supports arrays larger than 2TB. Adaptec's
storage management software uses the last flag to determine whether to
make available the creation of arrays larger than 2TB, otherwise a
warning is posted.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
I was amazed at how much embedded space was present in the aacraid
driver source files. Just selected five files from the set to clean up
for now and the attached patch swelled to 73K in size!
- Removed trailing space or tabs
- Removed spaces embedded within tabs
- Replaced leading 8 spaces with tabs
- Removed spaces before )
- Removed ClusterCommand as it was unused (noticed it as one triggered by above)
- Replaced scsi_status comparison with 0x02, to compare against SAM_STATUS_CHECK_CONDITION.
- Replaced a long series of spaces with tabs
- Replaced some simple if...defined() with ifdef/ifndef
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Actually there are several but one is trivially fixed
1. FSACTL_GET_NEXT_ADAPTER_FIB ioctl does not lock dev->fib_list
but needs to
2. Ditto for FSACTL_CLOSE_GET_ADAPTER_FIB
3. It is possible to construct an attack via the SRB ioctls where
the user obtains assorted elevated privileges. Various approaches are
possible, the trivial ones being things like writing to the raw media
via scsi commands and the swap image of other executing programs with
higher privileges.
So the ioctls should be CAP_SYS_RAWIO - at least all the FIB manipulating
ones. This is a bandaid fix for #3 but probably the ioctls should grow
their own capable checks. The other two bugs need someone competent in that
driver to fix them.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The promised min_t() cleanup. Purely cosmetic.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This replaces sizeof sense_buffer with SCSI_SENSE_BUFFERSIZE in
several LLDs. It's a preparation for the future changes to remove
sense_buffer array in scsi_cmnd structure.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Due to an internal limit associated with the AdapterTypeText field,
SMC required a product ID that overloaded the combined vendor and
product ID. A decision was made to ship the SMC products without a
vendor string dropping the defacto space that used to delineate vendor
and product to boot. To correct this, we needed to adjust the code in
the driver to parse out the vendor and product strings for the
adapter. We match of 'AOC' in the AdapterTypeText, if so we set the
vendor to SMC and place the entire AdapterTypeText into the product
field.
This only affects the cosmetic presentation of the Adapter vendor and
product in the logs and in sysfs.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Added support to respond to enclosure service events
(controller AIFs) to add, online or offline physical targets
reported to sg. Also added online and offlining of arrays.
Removed an automatic variable definition in a sub block that
hid an earlier definition, determined to be inert as the
sub-block use did not interfere. Bumped the driver versioning
to stamp the addition of this feature.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Some architectures require a call to flush_kernel_dcache_page for
processor spoofed DMA operations.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The adapter queue is divided up equally to all the arrays to prevent
command starvation to any individual array. On the other hand,
physical targets are only granted a queue depth of one each. The code
prior to this patch used to deal with the incremental discovery of
targets, but the driver knows how many arrays are present prior to the
scan so this knowledge is used to generate a better estimate for the
queue depth.
Remove the capability of 'physical=0' from preventing access to the
class of adapters that have the RAID/SCSI mode of operation since none
of the physicals on the SCSI channel are candidates ever for an array.
As always, the user can override this default queue depth policy by
making the appropriate adjustments utilizing sysfs.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
In experiments in the lab we managed to trigger an Adapter firmware
panic (BlinkLED) coincidentally while several pass-through ioctl
command from the management software were outstanding on a bug only
present on a class of RAID Adapters that require a hardware reset
rather than a commanded reset. The net result was an attempt to time
out the management software command as if it came from the SCSI layer
resulting in an OS panic.
Adapters that use commanded reset, management commands are returned
failed by the Adapter correctly. The adapter firmware panic that
resulted in this condition was also resolved, and there were no
adapters in the field with this specific firmware bug so we do not
expect any field reports. This is a rare or unlikely corner condition,
and no reports have ever been forwarded from the field.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The 'entry' automatic variable was defined at the top and within a
block that uses it, removed the definition from the block that uses
it. Some cosmetic changes were made while in the same file. This patch
should be inert.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Big endian systems issues discovered in the aacraid driver. Somewhat
reverses a patch from November 7th of last year that removed swap
operations because they formerly were being assigned to an u8 array
when they should have been assigned to an le32 array.
This patch is largely inert for any little endian processor
architecture. It resolves a bug in delivering the BlinkLED AIF event
to registered applications when the adapter or associated hardware was
reset due to ill health. A rare corner case occurrence, also largely
unnoticed by any as it was a new (untested!) feature.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The parameter 'info' is reused, renamed the second to sinfo to
represent supplemental adapter info, to suppress compile warning
message.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Report the RAID level string for the SCSI device representing the
array. Report is in /sys/class/scsi_device/#:#:#:#/device/level.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
aacraid.cache parameter, Disable Queue Flush commands:
bit 0 - Disable FUA in WRITE SCSI commands
bit 1 - Disable SYNCHRONIZE_CACHE SCSI command
bit 2 - Disable only if Battery not protecting adapter supplied Cache
e.g.: aacraid.cache=7 will disable the FUA and SYNCHRONIZE_CACHE
commands if the adapter has reported that it's cache is battery backed
up.
This parameter permits experimentation with tradeoffs between
performance and caching policy.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
As reported in http://bugzilla.kernel.org/show_bug.cgi?id=3D9133 it was
discovered that the PERC line of controllers lacked a key 64 bit
ScatterGather capable SCSI pass-through function. The adapters are still
capable of 64 bit ScatterGather I/O commands, but these two can not be
mixed. This problem was exacerbated by the introduction of the SCSI
Generic access to the DASD physical devices.
The fix for users before this patch is applied is aacraid.dacmode=3D0 on
the kernel command line to disable 64 bit I/O.
The enclosed patch introduces a new adapter quirk and tries to limp
along by enabling pass-through in situations where memory is 32 bit
addressable on 64 bit machines, or disable the pass-through functions
altogether. I expect that the check for 32 bit addressable memory to be
controversial in that it can be incorrect in non-Dell non-Intel systems
that PERC would never be installed under, the alternative is to disable
pass-through in all cases which could be reported as another regression.
Pass-through is used for SCSI Generic access to the physical devices, or
for the management applications to properly function.
In systems where this patch has disabled pass-through because it is
unsupportable in combination with I/O performance, the user can choose
to enable pass-through by turning off dacmode (aacraid.dacmode=3D0) or
limiting the discovered kernel memory (mem=3D4G) with an associated loss
in runtime performance. If we chose instead to turn off 64 bit dacmode
for the adapters with this quirk, then this would be reported as another
regression.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
On Wed, Nov 07, 2007 at 01:51:44PM -0500, Salyzyn, Mark wrote:
> Christoph Hellwig [mailto:hch@infradead.org] sez:
> > Did anyone run the driver through sparse to see if we have
> > more issues like this?
>
> There are some warnings from sparse, none like this one. I will deal
> with the warnings ...
Actually there are a lot of endianess warnings, fortunately most of them
harmless. The patch below fixes all of them up (including the ones in
the patch I replied to), except for aac_init_adapter which is really odd
and I don't know what to do.
[jejb fixed up rejections and checkpatch issues]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Mark Salyzyn <mark_salyzyn@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Some of our vendors have requested that our adapters ignore the hardware
reset attempts during recovery and have enforced this with changes in
Adapter Firmware. Some of our customers have requested the option to be
able to reset the adapter under adverse adapter failure, we even had a
few defects reported here considering it a regression that the Adapter
could not be reset. This patch addresses this dichotomy. The user can
force the adapter to be reset if it supports the IOP_RESET_ALWAYS
command, in cases where the adapter has been programmed to ignore the
reset, by setting the aacraid.check_reset parameter to a value of -1.
The driver will not reset an Adapter that does not support the reset
command(s).
This patch also fixes and cleans up some of the logic associated with
resetting the adapter.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Actually there are several but one is trivially fixed
1. FSACTL_GET_NEXT_ADAPTER_FIB ioctl does not lock dev->fib_list
but needs to
2. Ditto for FSACTL_CLOSE_GET_ADAPTER_FIB
3. It is possible to construct an attack via the SRB ioctls where
the user obtains assorted elevated privileges. Various approaches are
possible, the trivial ones being things like writing to the raw media
via scsi commands and the swap image of other executing programs with
higher privileges.
So the ioctls should be CAP_SYS_RAWIO - at least all the FIB manipulating
ones. This is a bandaid fix for #3 but probably the ioctls should grow
their own capable checks. The other two bugs need someone competent in that
driver to fix them.
Signed-off-by: Alan Cox <alan@redhat.com>
Acked-by: Mark Salyzyn <mark_salyzyn@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Got a panic in the threading code on an older kernel when the Adapter
failed to load properly and driver shut down apparently before any
threading had started, can not dupe. Expect that this may be relevant in
the latest kernel, but not sure. This patch does no harm, and should
alleviate the possibility of this panic.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Noticed on PowerPC allmod config build:
drivers/scsi/aacraid/commsup.c:1342: warning: large integer implicitly truncated to unsigned type
drivers/scsi/aacraid/commsup.c:1343: warning: large integer implicitly truncated to unsigned type
drivers/scsi/aacraid/commsup.c:1344: warning: large integer implicitly truncated to unsigned type
Also fix some whitespace on the changed lines.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Mark Salyzyn <mark_salyzyn@adaptec.com>
Signed-off-by: James <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Use of ptrdiff_t in places like
- if (!access_ok(VERIFY_WRITE, u_tmp->rx_buf, u_tmp->len))
+ if (!access_ok(VERIFY_WRITE, (u8 __user *)
+ (ptrdiff_t) u_tmp->rx_buf,
+ u_tmp->len))
is wrong; for one thing, it's a bad C (it's what uintptr_t is for; in general
we are not even promised that ptrdiff_t is large enough to hold a pointer,
just enough to hold a difference between two pointers within the same object).
For another, it confuses the fsck out of sparse.
Use unsigned long or uintptr_t instead. There are several places misusing
ptrdiff_t; fixed.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the various misspellings of "system", controller", "interrupt" and
"[un]necessary".
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
This option is true if a low-level driver can support sg
chaining. This will be removed eventually when all the drivers are
converted to support sg chaining. q->max_phys_segments is set to
SCSI_MAX_SG_SEGMENTS if false.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Too generic, clashes with ISDN.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If the driver fails to allocate the contiguous (DMAable) memory for
system reasons, we fail to load the instance, but then we try to free
the <nul> allocation in the cleanup code and we get a panic in
pci_free_consistent(). This is reported against an older kernel, hope
this is relevant for latest/greatest.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The patch is *much* smaller than the description. I am attempting to
answer to those that want to understand an issue that was reported in
May this year.
If a Sunrise Lake based card that requires an alternate reset mechanism
is set up to ignore the commanded IOP_RESET it reports 0x00000010
(IOP_RESET ignored) instead of 0x3803000F (use alternate reset mechanism
to reset all cores), and thus the reset platform function decides to
switch to IOP_RESET_ALWAYS because the reset platform function
parameters indicate that we *need* to reset the card. IOP_RESET_ALWAYS
then responds with the 0x3803000F return code, but alas we treat this as
an error instead of using the alternate reset mechanism (put a 0x03 into
the register offset 0x38). The reset fails, but the fact that the
IOP_RESET_ALWAYS command was issued has put the card in a purposeful
shutdown state in preparation for the alternate hardware reset to be
applied. Yuck.
IOP_RESET is ignored in internal production cards, typically to ensure
that we catch all adapter lockup issues without the driver progressing
further, so this would not appear to be a field issue and thus this
patch was destined to be only in the internal Adaptec source tree.
IOP_RESET_ALWAYS is reserved for
kexec/kdump/FirmwareUpdate/AutomatedTestFrames so we did not function as
expected in any case. Also in the past we have had OEMs specifically
request that cards not be resetable after a BlinkLED/FirmwareAssert for
one reason or another and To head off the possibility that the Sunrise
Lake based cards would suffer a similar fate, we propose the enclosed
fix.
Yinghai Lu of SUN had a pre-production card with IOP_RESET disabled when
he reported an issue to the linux kernel list back in May regarding a
kexec problem resulting from this reset being ignore. His fix was to
update the Firmware to one that did not ignore the IOP_RESET. Previous
kernels did not attempt to reset the adapter and that is why it surfaced
as a regression in his hands.
The current list of aacraid based cards that use Sunrise Lake:
9005:0285:9005:02b5 Adaptec 5445
9005:0285:9005:02b6 Adaptec 5805
9005:0285:9005:02b7 Adaptec 5085
9005:0285:9005:02c3 Adaptec 51205
9005:0285:9005:02c4 Adaptec 51605
9005:0285:9005:02ce Adaptec 51245
9005:0285:9005:02cf Adaptec 51645
9005:0285:9005:02d0 Adaptec 52445
9005:0285:9005:02d1 Adaptec 5405
9005:0285:9005:02b8 ICP ICP5445SL
9005:0285:9005:02b9 ICP ICP5085SL
9005:0285:9005:02ba ICP ICP5805SL
9005:0285:9005:02c5 ICP ICP5125SL
9005:0285:9005:02c6 ICP ICP5165SL
9005:0285:108e:7aac SUN STK RAID REM
9005:0285:108e:0286 SUN STK RAID INT
9005:0285:108e:0287 SUN STK RAID EXT
9005:0285:108e:7aae SUN STK RAID EM
All of these are publicly released with IOP_RESET enabled. So there is
no immediate need for this patch.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Customer running an application that issues SYNCHRONIZE_CACHE calls
directly noticed the broad stroke of the current implementation in the
aacraid driver resulting in multiple applications feeding I/O to the
storage causing the issuing application to stall for long periods of
time. By only waiting for the current WRITE commands, rather than all
commands, to complete; and those that are in range of the
SYNCHRONIZE_CACHE call that would associate more tightly with the
issuing application before telling the Firmware to flush it's dirty
cache, we managed to reduce the stalling. The Firmware itself still
flushes all the dirty cache associated with the array ignoring the
range, it just does so in a more timely manner.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Minor unimportant cuttings from the floor bundled in with a version
stamp update. Only controversial change is the dropping of Alan Cox
copyright on the nark.c module since that file has no code written by
him in it.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
On the SCSI layer ioctl path there is no implicit permissions check for
ioctls (and indeed other drivers implement unprivileged ioctls). aacraid
however allows all sorts of very admin only things to be done so should
check.
Signed-off-by: Alan Cox <alan@redhat.com>
Acked-by: Mark Salyzyn <mark_salyzyn@adaptec.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We need to newline terminate responses from nodes within the sysfs tree,
the Adapter status value reported by the reset adapter node is adjusted.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
On the SCSI layer ioctl path there is no implicit permissions check for
ioctls (and indeed other drivers implement unprivileged ioctls). aacraid
however allows all sorts of very admin only things to be done so should
check.
Signed-off-by: Alan Cox <alan@redhat.com>
Acked-by: "Salyzyn, Mark" <mark_salyzyn@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Report VPD inquiry page 0x80 with an unique array creation serial
number (CUID). When an array is created, the metadata stored on the
physical drives gets an unique serial number. This serial number
remains constant through array morphing or migration to other
controllers. This patch is a forward port and modification to survive
morphing and migration operations, of a similar piece of
(un-attributed author) code added to the SLES10 SP1 aacraid driver.
To test the results of the patch, observe that /dev/disk/by-id/
entries will show up for the arrays resulting from the udev rules.
Also, as per the udev rules, 'scsi_id -g -x -a -s /block/sd? -d
/dev/sd?' will report the ID_SERIAL as constructed from the inquiry
data.
It was reported to me that the 'ADPT' leading the serial number was bad
form, that the inquiry vendor field was enough to differentiate the
storage uniquely. Subsequent search found that another Adaptec AAC based
driver reported the 8 hex serial number only without such adornments, so
dropped ADPT to match. Resubmitting the patch with this alteration.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Incorrect dma mask was used for blinkled (firmware assert) recovery or
user initiated reset during initialization portion. Ensure that all
callers of aac_fib_map_free null out the fib allocation references to
prevent multiple free. Although serious sounding, no reports of these
problems have surfaced...
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
During an Adapter Initiated scan request, the query disk ioctl reports a
value of 2 rather than 1 for the valid field. This presents a problem
for some legacy management applications.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Support displaying long serial number information. Reuse sysfs handler
internally as helper.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The Dell PERC2/QC erroneously was listed as having the 31 bit limit
quirk on the interface allocations, removing the reference to repair
this oversight. Also, the 2 quad pci address (family) match catch-all
also retained the 31 bit limit and the 34 SG limit quirks in a paranoid
move. Now, many years later, we find that none of the Adapters that did
trigger with the family match had such quirks; these quirks are all
limited to the 4 quad pci address matches to select legacy adapters
already populated.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Salyzyn, Mark