Using console=ttyAM1 or console=ttyAMA1 resulted in an oops during
boot due to trying to drive the console before that port had been
registered. Fix this by checking whether the port is present before
allowing console setup to proceed.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes the unbalanced calls to enable_irq_wake() and
disable_irq_wake() in the AT91 (and AVR32) serial driver.
It should resolve these kernel messages:
Unbalanced IRQ x wake disable
BUG: warning at kernel/irq/manage.c:167/set_irq_wake()
Original patch from Marc Pignat.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A couple of whitespace cleanups, mainly in the AT91 header files.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
o MODPOST generates warning for i386 if compiled with CONFIG_RELOCATABLE=y
and serial console support is enabled.
o Serial console setup function, serial8250_console_setup(), is a non __init
function and it calls functions which are of type __init().
(uart_parse_options() and uart_set_options()). Assuming, setup will
be called during init time, changing serial8250_console_setup() to __init.
o Adding one more pattern to modpost whitelist. Console drivers might
have *_console structures containing references to setup functions which
can be of __init type. Don't generate warnings for those.
WARNING: vmlinux - Section mismatch: reference to .init.text: from .data between 'serial8250_console' (at offset 0xc05a33d8) and 'serial8250_reg'
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
The mpc52xx_uart_of_enumerate() function was added when adding 52xx
support to arch/powerpc, but it must not be called for arch/ppc.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We need to pass in the resource otherwise we cannot
release the region properly. We must know whether it is
an I/O or MEM resource.
Spotted by Eric Brower.
Signed-off-by: David S. Miller <davem@davemloft.net>
The uartlite driver used to always enable the port even if request_port
failed causing havoc. This patch fixes it.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adds initial support to 8250-pci for the Korenix Jetcard PCI serial
cards. The JC12xx cards are standard RS232-based serial cards utilising
the Oxford 16C950 device.
The JC14xx are RS422/RS485-based cards, but in order for these to be
supported natively, we will need additional tweaks to the 8250 layers so
we can specify some values for the 950's registers. Hence, these two
entries are commented out.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Standardize the miniscule percentage of occurrences of "depends" in
Kconfig files to "depends on", and update kconfig-language.txt to
reflect that.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Refactor Kconfig content to maximize nesting of menus by menuconfig and
xconfig.
Tested by simultaneously running `make xconfig` with and without
patch, and comparing displays.
Signed-off-by: Don Mullis <dwm@meer.net>
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is the grungy swap all the occurrences in the right places patch that
goes with the updates. At this point we have the same functionality as
before (except that sgttyb() returns speeds not zero) and are ready to
begin turning new stuff on providing nobody reports lots of bugs
If you are a tty driver author converting an out of tree driver the only
impact should be termios->ktermios name changes for the speed/property
setting functions from your upper layers.
If you are implementing your own TCGETS function before then your driver
was broken already and its about to get a whole lot more painful for you so
please fix it 8)
Also fill in c_ispeed/ospeed on init for most devices, although the current
code will do this for you anyway but I'd like eventually to lose that extra
paranoia
[akpm@osdl.org: bluetooth fix]
[mp3@de.ibm.com: sclp fix]
[mp3@de.ibm.com: warning fix for tty3270]
[hugh@veritas.com: fix tty_ioctl powerpc build]
[jdike@addtoit.com: uml: fix ->set_termios declaration]
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Acked-by: Peter Oberparleiter <oberpar@de.ibm.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The pl010 primecell documentation specifies that an error indicated via RSR
should be cleared by a write to ECR. We didn't do this, which was causing
errors to be re-reported on every call to pl010_rx_chars().
Doing a write to ECR once we detect an error appears to prevent the ep93xx
console UART driver from going into a mode where it reports "ttyAM0: X
input overrun(s)" every couple of keystrokes.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add suspend/resume methods to drivers/serial/8250_pnp.c. Tested on a
P4/HT 16550A box, ttyS0 login survives across suspend to ram.
[akpm@osdl.org: cleanups]
Signed-off-by: Mike Galbraith <efault@gmx.de>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This a set of fixes mostly to make the driver actually work:
1. Actually select the line for setting parameters and receiver
disable/enable.
2. Select the line for receive and transmit interrupt handling correctly.
3. Report the transmitter empty state correctly.
4. Set the I/O type of ports correctly.
5. Perform polled transmission correctly.
6. Don't fix the console line at ttyS3.
7. Magic SysRq support.
8. Various small bits here and there.
Tested with a DECstation 2100 (thanks Flo for making this possible).
[akpm@osdl.org: fix typo]
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Pass struct dev pointer to dma_cache_sync()
dma_cache_sync() is ill-designed in that it does not have a struct device
pointer argument which makes proper support for systems that consist of a
mix of coherent and non-coherent DMA devices hard. Change dma_cache_sync
to take a struct device pointer as first argument and fix all its callers
to pass it.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is on our "Envoy" boxes which we have, according to the documentation, an
"Exar ST16C554/554D Quad UART with 16-byte Fifo's". The box also has two
other "on-board" serial ports and a modem chip.
The two on-board serial UARTs were being detected along with the first two
Exar UARTs. The last two Exar UARTs were not showing up and neither was the
modem.
This patch was the only way I could the kernel to see beyond the standard four
serial ports and get all four of the Exar UARTs to show up.
[akpm@osdl.org: build fix]
Signed-off-by: Paul B Schroeder <pschroeder@uplogix.com>
Cc: Lennart Sorensen <lsorense@csclub.uwaterloo.ca>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a driver for the Xilinx uartlite serial controller used in boards with
the PPC405 core in the Xilinx V2P/V4 fpgas.
The hardware is very simple (baudrate/start/stopbits fixed and no break
support). See the datasheet for details:
http://www.xilinx.com/bvdocs/ipcenter/data_sheet/opb_uartlite.pdf
See http://thread.gmane.org/gmane.linux.serial/1237/ for the email thread.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Olof Johansson <olof@lixom.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some updates for the old ColdFire serial driver:
. support 3 and 4 UARTs on some ColdFire parts that have them
. enable multifunction pins to serial for 527x CPU's
. support the 5272 UART's fractional baud rate divisor
. switch driver name to "mcfserial"
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This syncs up the SH clock framework with the linux/clk.h API,
for which there were only some minor changes required, namely
the clk_get() dev_id and subsequent callsites.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This makes the early printk support somewhat more flexible,
moving the port definition to a config option, and making the
port initialization configurable for sh-ipl+g users.
At the same time, this allows us to trivially wire up the
SH7780 SCIF0, so that's thrown in too more or less for free.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This implements initial support for the SH7206 (SH-2A) and SH7619
(SH-2) MMU-less CPUs.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
struct pcmcia_device *p_dev->conf.ConfigBase and .Present are set in almost
all PCMICA driver right at the beginning, using the same calls but slightly
different implementations. Unfiy this in the PCMCIA core.
Includes a small bugfix ("drivers/net/pcmcia/xirc2ps_cs.c: remove unused
label") from and Signed-off-by Adrian Bunk <bunk@stusta.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
As we read out the manufactor and card_id from the PCMCIA device in the
PCMCIA core, and device drivers can access those reliably in struct
pcmcia_device's fields manf_id and card_id, remove additional (and partly
broken) manf_id and card_id detection logic from PCMCIA device drivers.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Add IDs for Elan serial PCMCIA devices. In addition, move the
pdaudio_cf driver from matching based on manf_id and card_id to
the more specific prod_id1 and prod_id2 to avoid false
positives.
Signed-off-by: Tony Olech <tony.olech@elandigitalsystems.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Needed to support mpc52xx boards in arch/powerpc. This patch
retains the platform_bus support when compiling for arch/ppc,
but uses the of_platform bindings for arch/powerpc.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Single typo fix and whitespace changes. In preparation for heavy
changes to this driver when support for arch/powerpc is added.
Since the driver will be changing significantly anyway, then may
as well take the opportunity to clean it up first.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Updated some of the comments in the atmel_serial.h header detailing
which bits are only available on the AT91RM9200 or the AT91SAM9xx
processors.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1. The CPU identification has moved from <system.h> to <cpu.h>.
2. AT91RM9200_BASE_US0 is only defined if we are compiling in support
for the AT91RM9200. Therefore we need to replace the CONFIG_ARM ifdef
with CONFIG_ARCH_AT91RM9200
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The below hunk was missed from the recent patch, and now, there are somewhat
inconsistent definitions:
in cpm_uart.h:
int __init cpm_uart_init_portdesc(void);
in cpm_uart_cpm1.c:
int __init cpm_uart_init_portdesc(void)
{
}
in cpm_uart_cpm2.c:
int cpm_uart_init_portdesc(void)
{
}
Signed-off-by: Kalle Pokki <kalle.pokki@iki.fi>
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch updates the drivers (and other files) which include the
hardware headers. This fixes the breakage introduced in patches 3950/1
and 3951/1 (those patches were getting big).
The AVR32 architecture uses the same serial driver and had its own copy
of at91rm9200_pdc.h. Renamed it to at91_pdc.h
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch replaces the arch_identify() in system.h with a set of
cpu_is_XXX() macro's. This allows for compile-time checking of the
target AT91 processor.
Original patch from David Brownell.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The cpm_uart driver is initialised incorrectly, if there is a frame buffer
console, and CONFIG_SERIAL_CPM_CONSOLE is defined. The driver fails to
call cpm_uart_init_portdesc() and set_lineif() in this case.
Signed-off-by: Kalle Pokki <kalle.pokki@iki.fi>
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The SMC and SCC hardware transmitter is enabled at the wrong
place. Simply writing twice to the non-console port, like
$ echo asdf > /dev/ttyCPM1
$ echo asdf > /dev/ttyCPM1
puts the shell into endless uninterruptible sleep, since the
transmitter is stopped after the first write, and is not enabled
before the shutdown function of the second write. Thus the transmit
buffers are never emptied.
Signed-off-by: Kalle Pokki <kalle.pokki@iki.fi>
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix typo (repeated) in serial Kconfig.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The SGI PCI-RT card, based on the SGI IOC4 chip, will be made available on
Altix XE (x86_64) platforms in the near future. As such it is now a
misnomer for the IOC4 base device driver to live under drivers/sn, and
would complicate builds for non-SN2.
This patch moves the IOC4 base driver code from drivers/sn to drivers/misc,
and updates the associated Makefiles and Kconfig files to allow building on
non-SN2 configs. Due to the resulting change in link order, it is now
necessary to use late_initcall() for IOC4 subdriver initialization.
[akpm@osdl.org: __udivdi3 fix]
[akpm@osdl.org: fix default in Kconfig]
Acked-by: Pat Gefre <pfg@sgi.com>
Acked-by: Jeremy Higdon <jeremy@sgi.com>
Signed-off-by: Brent Casavant <bcasavan@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix this 2.6.19-rc1 build warnings from modpost:
WARNING: vmlinux - Section mismatch: reference to .init.text:sunzilog_console_setup from .data between 'sunzilog_console' (at offset 0x8394) and 'devices_subsys'
Signed-off-by: Martin Habets <errandir_news@mph.eclipse.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Eliminate casts to/from void*
- Eliminate checks for conditions that never occur. These typically
fall into two classes:
1) Checking for 'dev_id == NULL', then it is never called with
NULL as an argument.
2) Checking for invalid irq number, when the only caller (the
system) guarantees the irq handler is called with the proper
'irq' number argument.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
The atmel_console_get_options() function initializes the baud,
parity and bits settings from the actual hardware setup, in
case it has been initialized by a e.g. boot loader.
The baud rate, however, is not necessarily exactly equal to one of
the standard baud rates (115200, etc.) This means that the baud rate
calculated by this function may be slightly higher or slightly lower
than one of the standard baud rates.
If the baud rate is slightly lower than the target, this causes
problems when uart_set_option() tries to match the detected baud rate
against the standard baud rate, as it will always select a baud rate
that is lower or equal to the target rate. For example if the
detected baud rate is slightly lower than 115200, usart_set_options()
will select 57600.
This patch fixes the problem by subtracting 1 from the value in BRGR
when calculating the baud rate. The detected baud rate will thus
always be higher than the nearest standard baud rate, and
uart_set_options() will end up doing the right thing.
Tested on ATSTK1000 and AT91RM9200-EK boards. Both are broken without
this patch.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make CONFIG_SERIAL_ATMEL selectable on AVR32 and #ifdef out some ARM-
specific code in the driver.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In order to initialize the serial console early, the atmel_serial
driver had to do a hack where it compared the physical address of the
port with an address known to be permanently mapped, and used it as a
virtual address. This got around the limitation that ioremap() isn't
always available when the console is being initalized.
This patch removes that hack and replaces it with a new "regs" field
in struct atmel_uart_data that the board-specific code can initialize
to a fixed virtual mapping for platform devices where this is possible.
It also initializes the DBGU's regs field with the address the driver
used to check against.
On AVR32, the "regs" field is initialized from the physical base
address when this it can be accessed through a permanently 1:1 mapped
segment, i.e. the P4 segment.
If regs is NULL, the console initialization is delayed until the "real"
driver is up and running and ioremap() can be used.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Russell King