Setting CFLAG bits is all well and good but you must sort out ispeed and
ospeed properly.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bring ezusb and whiteheat into line with the coding style
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
USB serial likes to use port->tty back pointers for the real work it does and
to do so without any actual locking. Unfortunately when you consider hangup
events, hangup/parallel reopen or even worse hangup followed by parallel close
events the tty->port and port->tty pointers are not guaranteed to be the same
as port->tty is the active tty while tty->port is the port the tty may or
may not still be attached to.
So rework the entire API to pass the tty struct. For console cases we need
to pass both for now. This shows up multiple drivers that immediately crash
with USB console some of which have been fixed in the process.
Longer term we need a proper tty as console abstraction
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
in the error case the ipaq driver leaves a dangling pointer to already
freed memory that will be freed again.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB debug port only supports 8 byte rx/tx packets. Although spec implies that
"if a packet larger than eight bytes is received from the remote computer, the
device must break the larger packet into eight-byte packets before sending the
data to the Debug Port", the real PLX NET20DC device does not handle it right -
data is corrupted on debug port end if serial interface sends >8 byte urbs.
Patch below fixes the issue by limiting tx urb to 8 byte.
Signed off by: Aleks Gorelov <dared1st@yahoo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb serial decrements the pm counter even if an interface has been
disconnected. If it was a logical disconnect the interface may belong
already to another driver. This patch introduces a check for disconnected
interfaces.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: Stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The 28xb, as documented in comments, has the same ID's as the 28x.
Remove the duplicated ID's from the device tables, and expand the
comment to document this.
Signed-off-by: Ben Collins <ben.collins@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
fix the following sparse warning:
drivers/usb/serial/usb-serial.c:927:43: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/usb-serial.c:927:43: expected unsigned int *minor
drivers/usb/serial/usb-serial.c:927:43: got int *<noident>
CHECK drivers/usb/serial/generic.c
Signed-off-by: Andre Haupt <andre@bitwigglers.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
General cleanup on ir-usb module. Introduced
a common header that could be used also on
usb gadget framework.
Lot's of cleanups and now using macros from the header
file.
Signed-off-by: Felipe Balbi <me@felipebalbi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The get/set 2101_config helpers take an unsigned int rather than an
int. It is safe to change these in each case and may even produce
better code as it will be an unsigned divide rather than a signed
divide in places. All other manipulation was setting/masking bits
which will not be affected by the sign change.
Fixes the following sparse warnings:
drivers/usb/serial/cp2101.c:378:44: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:378:44: expected unsigned int *data
drivers/usb/serial/cp2101.c:378:44: got int *<noident>
drivers/usb/serial/cp2101.c:388:40: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:388:40: expected unsigned int *data
drivers/usb/serial/cp2101.c:388:40: got int *<noident>
drivers/usb/serial/cp2101.c:413:42: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:413:42: expected unsigned int *data
drivers/usb/serial/cp2101.c:413:42: got int *<noident>
drivers/usb/serial/cp2101.c:421:42: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:421:42: expected unsigned int *data
drivers/usb/serial/cp2101.c:421:42: got int *<noident>
drivers/usb/serial/cp2101.c:444:42: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:444:42: expected unsigned int *data
drivers/usb/serial/cp2101.c:444:42: got int *<noident>
drivers/usb/serial/cp2101.c:451:42: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:451:42: expected unsigned int *data
drivers/usb/serial/cp2101.c:451:42: got int *<noident>
drivers/usb/serial/cp2101.c:458:42: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:458:42: expected unsigned int *data
drivers/usb/serial/cp2101.c:458:42: got int *<noident>
drivers/usb/serial/cp2101.c:471:42: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:471:42: expected unsigned int *data
drivers/usb/serial/cp2101.c:471:42: got int *<noident>
drivers/usb/serial/cp2101.c:481:42: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:481:42: expected unsigned int *data
drivers/usb/serial/cp2101.c:481:42: got int *<noident>
drivers/usb/serial/cp2101.c:561:41: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:561:41: expected unsigned int *data
drivers/usb/serial/cp2101.c:561:41: got int *<noident>
drivers/usb/serial/cp2101.c:591:45: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:591:45: expected unsigned int *data
drivers/usb/serial/cp2101.c:591:45: got int *<noident>
drivers/usb/serial/cp2101.c:597:41: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:597:41: expected unsigned int *data
drivers/usb/serial/cp2101.c:597:41: got int *<noident>
drivers/usb/serial/cp2101.c:608:45: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:608:45: expected unsigned int *data
drivers/usb/serial/cp2101.c:608:45: got int *<noident>
drivers/usb/serial/cp2101.c:614:41: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:614:41: expected unsigned int *data
drivers/usb/serial/cp2101.c:614:41: got int *<noident>
drivers/usb/serial/cp2101.c:623:45: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:623:45: expected unsigned int *data
drivers/usb/serial/cp2101.c:623:45: got int *<noident>
drivers/usb/serial/cp2101.c:680:50: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:680:50: expected unsigned int *data
drivers/usb/serial/cp2101.c:680:50: got int *<noident>
drivers/usb/serial/cp2101.c:690:43: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:690:43: expected unsigned int *data
drivers/usb/serial/cp2101.c:690:43: got int *<noident>
drivers/usb/serial/cp2101.c:715:41: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:715:41: expected unsigned int *data
drivers/usb/serial/cp2101.c:715:41: got int *<noident>
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes CVS keywords that weren't updated for a long time
from comments.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sort out the insane naming like "OperationalFirmwareVersion" which seems
designed to cause formatting problems and RSI
Merge various common code together
Clean up the pointlessly complex and spread about MCR handling
This is really just the low hanging fruit.
Needs lots of testing before it goes upstream so testers and reports
appreciated
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The bus_id field is going away, use the dev_set_name() function
to set it properly.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The bus_id field is going away, use the dev_name() function instead.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Version number provided in first HEX record.
Signed-off-by: Jaswinder Singh <jaswinder@infradead.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The reason for forcing a number of ports should be documented.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Thanks to umesh b <umesh.kollam@gmail.com> for the information here.
Cc: umesh b <umesh.kollam@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here's a new device ID for the ftdio_sio driver.
The diff is with linus's tree as of this morning.
The device is the RigExpert Tiny USB Soundcard Transceiver Interface for ham
radio.
(I didn't actually test this. A fellow ham couldn't get the device to work, and
I suggested binding the device ID using sysfs - see
"http://jk.ufisa.uninett.no/usb/". However, he had had moved on to other things
by then. I guess adding the device ID to the kernel "on spec" won't hurt.
The relevant part of cat /proc/bus/usb/devices shows:
T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0403 ProdID=ed22 Rev= 5.00
S: Manufacturer=FTDI
S: Product=MixW RigExpert Tiny
S: SerialNumber=00000000
C:* #Ifs= 2 Cfg#= 1 Atr=80 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=83(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
)
From: Jon K Hellan <hellan@acm.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add the interface info matching to all Huawei cards, as they all also
contain a Mass Storage Device interface (usually containing Windows
drivers) which should not get bound by this driver.
See also drivers/usb/storage/unusual_devs.h
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I've just got a USB GPRS/EDGE modem branded Manufacturer Micromax Model
MMX610U (see http://www.airtel.in/level2_t3data.aspx?path=1/106/179)
working by adding another product ID to pl2303. Modem info reports same
module as Max Arnold's i.e.SIMCOM SIM600 but with product ID 0x0612
(cf Ox0611).
From: Steve Murphy <steve@gnusis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Cox