We weren't explicitly setting the page table bits we desired
in user_prot in the protection table, which resulted in the
user mappings for v6 CPUs being marked global.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We run into problems if we blindly enable L2 prefetching without
checking that the L2 cache is actually enabled. Additionaly, if we
disable the L2 cache we need to ensure that we disable L2 prefetching.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In adjusting the logic for SLB miss for the dynamic hugepage stuff, I
messed up the !CONFIG_HUGETLB_PAGE case, failing to set the SLB flags
properly.
This fixes it. It also streamlines the logic for the HUGETLB_PAGE case
(removing a couple of branches) while we're at it.
Booted, and roughly tested on POWER5 (with and without HUGETLB_PAGE),
iSeries/RS64 (no hugepage available), and G5 (with and without
HUGETLB_PAGE).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
No point checking what CPU architecture level we have each time
within the loop, so precompute the base PMD flags outside the
loop.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
The prototype for sys_fadvise64_64() is:
long sys_fadvise64_64(int fd, loff_t offset, loff_t len, int advice)
The argument list is therefore as follows on legacy ABI:
fd: type int (r0)
offset: type long long (r1-r2)
len: type long long (r3-sp[0])
advice: type int (sp[4])
With EABI this becomes:
fd: type int (r0)
offset: type long long (r2-r3)
len: type long long (sp[0]-sp[4])
advice: type int (sp[8])
Not only do we have ABI differences here, but the EABI version requires
one additional word on the syscall stack.
To avoid the ABI mismatch and the extra stack space required with EABI
this syscall is now defined with a different argument ordering
on ARM as follows:
long sys_arm_fadvise64_64(int fd, int advice, loff_t offset, loff_t len)
This gives us the following ABI independent argument distribution:
fd: type int (r0)
advice: type int (r1)
offset: type long long (r2-r3)
len: type long long (sp[0]-sp[4])
Now, since the syscall entry code takes care of 5 registers only by
default including the store of r4 to the stack, we need a wrapper to
store r5 to the stack as well. Because that wrapper was missing and was
always required this means that sys_fadvise64_64 never worked on ARM and
therefore we can safely reuse its syscall number for our new
sys_arm_fadvise64_64 interface.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Change sn2-specific calls into generic functions. Without this change
the uncached allocator will not work on non-sn2 platforms.
Signed-off-by: Greg Edwards <edwardsg@sgi.com>
Signed-off-by: Martin Hicks <mort@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Patch from Catalin Marinas
Minor compilation error fix.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Steve Longerbeam
Adds an implementation of unaligned LDRD and STRD fixups.
Also fixes a bug where do_alignment() would misinterpret and
fixup an unaligned LDRD/STRD as LDRH/STRH, causing memory
corruption.
This is the same as Patch #2867/1, but with minor whitespace
and comments changes, plus a check for arch-level >= v5TE
before printing ai_dword count in proc_alignment_read().
Signed-off-by: Steve Longerbeam <stevel@mwwireless.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
timer_dyn_reprogram() fails with an OOPS if the
configuration for CONFIG_NO_IDLE_HZ is enabled, and
the system has no support for it.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The following patch fixes two warnings in arch/ppc/syslib/m8xx_setup.c
Signed-off-by: Marcelo Tosatti <marcelo.tosatti@cyclades.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I had some time to think about PCI assign issues in 2.6.13-rc series.
The major problem here is that we call pci_assign_unassigned_resources()
way too early - at subsys_initcall level. Therefore we give no chances
to ACPI and PnP routines (called at fs_initcall level) to reserve their
respective resources properly, as the comments in drivers/pnp/system.c
and drivers/acpi/motherboard.c suggest:
/**
* Reserve motherboard resources after PCI claim BARs,
* but before PCI assign resources for uninitialized PCI devices
*/
So I moved the pci_assign_unassigned_resources() call to
pcibios_assign_resources() (fs_initcall), which should hopefully fix a
lot of problems and make PCIBIOS_MIN_IO tweaks unnecessary.
Other changes:
- remove resource assignment code from pcibios_assign_resources(), since
it duplicates pci_assign_unassigned_resources() functionality and
actually does nothing in 2.6.13;
- modify ROM assignment code as per Ben's suggestion: try to use firmware
settings by default (if PCI_ASSIGN_ROMS is not set);
- set CARDBUS_IO_SIZE back to 4K as it's a wonderful stress test for
various setups.
Confirmed by Tero Roponen <teanropo@cc.jyu.fi> (who had problems with
the 4kB CardBus IO size previously).
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The {BEGIN,END}_FTR_SECTION asm macros used in ppc64 to nop out
sections of code at runtime cannot be nested. However, we do nest
them in hash_low.S. We get away with it there, because there is
nothing between the BEGIN markers for each section. However, that's
confusing to someone reading the code.
This patch removes the nested ifset and ifclr feature sections,
replacing them with a single feature section in the full mask/value
form.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch fixes a rare memory leak found by Coverity.
Signed-off-by: Joel Schopp <jschopp@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
While ppc64 has the CONFIG_HZ Kconfig option, it wasnt actually being
used. Connect it up and set all platforms to 250Hz.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Here's the 970MP's PVR (processor version register) entry for oprofile.
Signed-off-by: Jake Moilanen <moilanen@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some RS64-based machines (p620, F80, others) have problems with firmware
returning 0xdeadbeef instead of failure to allocations that end at the
1GB mark.
We have two options:
1. Detect the undocumented 0xdeadbeef return value and interpret it as
a failure.
2. Avoid allocating that high.
(2) is really the cleaner solution here. 768MB is plenty of room so use
that as the max alloc_top instead of 1GB.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The ppc and ppc64 trees are hopefully going to merge over time, so this
patch begins the process by creating a place for the merging of the
header files.
Create include/asm-powerpc (and move linkage.h into it from
asm-{ppc,ppc64} since we don't like empty directories). Modify the
ppc and ppc64 Makefiles to cope.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Create vio_bus_ops so that we just pass a structure to vio_bus_init
instead of three separate function pointers.
Rearrange vio.h to avoid forward references. vio.h only needs
struct device_node from prom.h so remove the include and just
declare it.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Take some assignments out of vio_register_device_common and
rename it to vio_register_device.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Formatting changes to vio.c to bring it closer to the
kernel coding standard.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
gcc 3.4 (at least the build we are using) puts the gcc generated .ident
string into a .note section at the end of the files it compiles (gcc
3.3.3-hammer and gcc 4.0.2 Debian puts it in the .text section). This
means that the lparmap.s file we produce in the iSeries build may end with
a .note section. When we include it into head.S, the assembler can no
longer resolve some of the conditional branches since the target label
ends up too far away. This patch just forces us back to the .text section
after including lparmap.s.
The breakage was caused by my patch "iSeries build with newer assemblers
and compilers" (sha1-id: 2ad5649662).
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
A mistake rebasing the series of ppc64 head.S cleanup patches meant
the #include of lparmap.s, needed for iSeries was lost. This patch
puts it back again.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Patch from Deepak Saxena
Working on adding support for 36-bit static mappings for ARMv6 and
Intel's XSC3 core and noticed that alloc_init_supersection currently
increments the phys addr by 1MB on each of the 16 iterations and then
forces alignment to supersection size (16MB). This is really uneeded
b/c we have already forced the phys address to be 16MB aligned in
create_mapping(). Furthermore, this breaks 36-bit addressing b/c bits
[23:20] of the PMD contain bits [35:32] of the physical address and
the masking causes us to loose those bits thus ending up with an
incorrect virt -> phys translation. The other option is to have an
alloc_init_supersection36.
Tested on Intel IXP2350 CPU with 36-bit static I/O mappings.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Show the state of DVS (Dynamic Voltage Scaling) when
starting up on the S3C2440
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Add the definitions for the S3C2410_CLKSLOW registers to
the header files, and show the values when the system
starts up
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
This patch implements the set_irq_type() hooks for configuring GPIO
IRQ type and updates all the platforms to use it instead of the
gpio_line_config() function which is now used to configure input
vs. output on the pins.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
None of the board-specific map_io routines do anything, so kill them.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It appears that a memory barrier soon after a mispredicted
branch, not just in the delay slot, can cause the hang
condition of this cpu errata.
So move them out-of-line, and explicitly put them into
a "branch always, predict taken" delay slot which should
fully kill this problem.
Signed-off-by: David S. Miller <davem@davemloft.net>
When the spinlock routines were moved out of line into
kernel/spinlock.c this made it so that the debugging
spinlocks record lock acquisition program counts in the
kernel/spinlock.c functions not in their callers.
This makes the debugging info kind of useless.
So record the correct caller's program counter and
now this feature is useful once more.
Signed-off-by: David S. Miller <davem@davemloft.net>
Removed sparc architecture specific users of asm/segment.h and
asm-sparc/segment.h itself
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removed sparc64 architecture specific users of asm/segment.h and
asm-sparc64/segment.h itself
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current uncorrectable error handling was poor enough
that the processor could just loop taking the same
trap over and over again. Fix things up so that we
at least get a log message and perhaps even some register
state.
In the process, much consolidation became possible,
particularly with the correctable error handler.
Prefix assembler and C function names with "spitfire"
to indicate that these are for Ultra-I/II/IIi/IIe only.
More work is needed to make these routines robust and
featureful to the level of the Ultra-III error handlers.
Signed-off-by: David S. Miller <davem@davemloft.net>
Verify we really are taking a data access exception trap, at TL1, from
one of the window spill/fill handlers.
Else call a new function, data_access_exception_tl1, to log the error.
Signed-off-by: David S. Miller <davem@davemloft.net>
1) Read ASI_IMMU SFSR not ASI_DMMU.
2) IMMU has no SFAR, read TPC instead
3) Delete old and incorrect comment about the DTLB protection
trap having a dependency on the SFSR contents in order to
function correctly
Signed-off-by: David S. Miller <davem@davemloft.net>
It has been reported that the way Linux handles NODEFER for signals is
not consistent with the way other Unix boxes handle it. I've written a
program to test the behavior of how this flag affects signals and had
several reports from people who ran this on various Unix boxes,
confirming that Linux seems to be unique on the way this is handled.
The way NODEFER affects signals on other Unix boxes is as follows:
1) If NODEFER is set, other signals in sa_mask are still blocked.
2) If NODEFER is set and the signal is in sa_mask, then the signal is
still blocked. (Note: this is the behavior of all tested but Linux _and_
NetBSD 2.0 *).
The way NODEFER affects signals on Linux:
1) If NODEFER is set, other signals are _not_ blocked regardless of
sa_mask (Even NetBSD doesn't do this).
2) If NODEFER is set and the signal is in sa_mask, then the signal being
handled is not blocked.
The patch converts signal handling in all current Linux architectures to
the way most Unix boxes work.
Unix boxes that were tested: DU4, AIX 5.2, Irix 6.5, NetBSD 2.0, SFU
3.5 on WinXP, AIX 5.3, Mac OSX, and of course Linux 2.6.13-rcX.
* NetBSD was the only other Unix to behave like Linux on point #2. The
main concern was brought up by point #1 which even NetBSD isn't like
Linux. So with this patch, we leave NetBSD as the lonely one that
behaves differently here with #2.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Paulus, I think this is now a reasonable candidate for the post-2.6.13
queue.
Relax address restrictions for hugepages on ppc64
Presently, 64-bit applications on ppc64 may only use hugepages in the
address region from 1-1.5T. Furthermore, if hugepages are enabled in
the kernel config, they may only use hugepages and never normal pages
in this area. This patch relaxes this restriction, allowing any
address to be used with hugepages, but with a 1TB granularity. That
is if you map a hugepage anywhere in the region 1TB-2TB, that entire
area will be reserved exclusively for hugepages for the remainder of
the process's lifetime. This works analagously to hugepages in 32-bit
applications, where hugepages can be mapped anywhere, but with 256MB
(mmu segment) granularity.
This patch applies on top of the four level pagetable patch
(http://patchwork.ozlabs.org/linuxppc64/patch?id=1936).
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
You can't call get_property() on a NULL node, so check if of_chosen is set
in check_for_initrd().
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
arch/ppc64/kernel/setup.c | 20 ++++++++++++--------
1 files changed, 12 insertions(+), 8 deletions(-)
Signed-off-by: Paul Mackerras <paulus@samba.org>
unflatten_device_tree() doesn't check if lmb_alloc() succeeds or not, it
should. All it can do is panic, but at least there's an error message
(assuming you have some sort of console at that point).
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
arch/ppc64/kernel/prom.c | 9 +++++++--
1 files changed, 7 insertions(+), 2 deletions(-)
Signed-off-by: Paul Mackerras <paulus@samba.org>
When unflatten_dt_node() fails to find an OF_DT_END_NODE tag it prints
"Weird tag at start of node", this should be "Weird tag at end of node".
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
arch/ppc64/kernel/prom.c | 2 +-
1 files changed, 1 insertion(+), 1 deletion(-)
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch moves power4_enable_pmcs() to arch/ppc64/kernel/pmc.c.
I've tested it on P5 LPAR and P4. It does what it used to.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If both CONFIG_XMON and CONFIG_XMON_DEFAULT is enabled in the .config,
there is no way to disable xmon again. setup_system calls first xmon_init,
later parse_early_param. So a new 'xmon=off' cmdline option will do the right
thing.
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We can now remove CONFIG_MSCHUNKS as it doesn't do anything interesting
anymore.
The only macro in abs_addr.h which is called by non-iSeries code is
phys_to_abs(), so remove the other dummy implementations, and we add a
firmware feature check to phys_to_abs().
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
lmb_phys_mem_size() can always return lmb.memory.size, as long as it's called
after lmb_analyze(), which it is. There's no need to recalculate the size on
every call.
lmb_analyze() was calculating a few things we then threw away, so just don't
calculate them to start with.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Greg Ungerer