Rather than explicitly handing the features to the lower-level, we just
hand the virtio_device and have it set the features. This make it clear
that it has the chance to manipulate the features of the device at this
point (and that all feature negotiation is already done).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
We assign feature bits as required, but it makes sense to reserve some
for the particular transport, rather than the particular device.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Hook up to the probe() and remove() methods in bus_type
rather than device_driver. The latter has been preferred
since 2.6.16.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
lguest (in rusty's use-tun-ringfd patch) assumes that the
guest has updated its feature bits before setting its status
to VIRTIO_CONFIG_S_DRIVER_OK.
That's pretty reasonable, so let's make it so.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Anthony Liguori points out that three different transports use the virtio code,
but each one keeps its own counter to set the virtio_device's index field. In
theory (though not in current practice) this means that names could be
duplicated, and that risk grows as more transports are created.
So we move the selection of the unique virtio_device.index into the common code
in virtio.c, which has the side-benefit of removing duplicate code.
The only complexity is that lguest and S/390 use the index to uniquely identify
the device in case of catastrophic failure before register_virtio_device() is
called: now we use the offset within the descriptor page as a unique identifier
for the printks.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Carsten Otte <cotte@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Chris Lalancette <clalance@redhat.com>
Cc: Anthony Liguori <anthony@codemonkey.ws>
Chris Lalancette <clalance@redhat.com> points out that virtio.c sets all device
names to '0', '1', etc, which looks silly in /proc/interrupts. We change this
from '%d' to 'virtio%d'.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Carsten Otte <cotte@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Chris Lalancette <clalance@redhat.com>
Cc: Anthony Liguori <anthony@codemonkey.ws>
A recent proposed feature addition to the virtio block driver revealed
some flaws in the API: in particular, we assume that feature
negotiation is complete once a driver's probe function returns.
There is nothing in the API to require this, however, and even I
didn't notice when it was violated.
So instead, we require the driver to specify what features it supports
in a table, we can then move the feature negotiation into the virtio
core. The intersection of device and driver features are presented in
a new 'features' bitmap in the struct virtio_device.
Note that this highlights the difference between Linux unsigned-long
bitmaps where each unsigned long is in native endian, and a
straight-forward little-endian array of bytes.
Drivers can still remove feature bits in their probe routine if they
really have to.
API changes:
- dev->config->feature() no longer gets and acks a feature.
- drivers should advertise their features in the 'feature_table' field
- use virtio_has_feature() for extra sanity when checking feature bits
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This is needed for the virtio PCI device to be compiled as a module.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
A reset function solves three problems:
1) It allows us to renegotiate features, eg. if we want to upgrade a
guest driver without rebooting the guest.
2) It gives us a clean way of shutting down virtqueues: after a reset,
we know that the buffers won't be used by the host, and
3) It helps the guest recover from messed-up drivers.
So we remove the ->shutdown hook, and the only way we now remove
feature bits is via reset.
We leave it to the driver to do the reset before it deletes queues:
the balloon driver, for example, needs to chat to the host in its
remove function.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Previously we used a type/len pair within the config space, but this
seems overkill. We now simply define a structure which represents the
layout in the config space: the config space can now only be extended
at the end.
The main driver-visible changes:
1) We indicate what fields are present with an explicit feature bit.
2) Virtqueues are explicitly numbered, and not in the config space.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The virtio code never hooked through the ->remove callback. Although
noone supports device removal at the moment, this code is already
needed for module unloading.
This of course also revealed bugs in virtio_blk, virtio_net and lguest
unloading paths.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This adds the logic to convert the virtio ids into module aliases, and
includes a modalias entry in sysfs and the env var to make probing work.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This attempts to implement a "virtual I/O" layer which should allow
common drivers to be efficiently used across most virtual I/O
mechanisms. It will no-doubt need further enhancement.
The virtio drivers add buffers to virtio queues; as the buffers are consumed
the driver "interrupt" callbacks are invoked.
There is also a generic implementation of config space which drivers can query
to get setup information from the host.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Dor Laor <dor.laor@qumranet.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Rusty Russell