Add support for Zoom2 board. Zoom2 machine driver
connects both codec DAIs (audio and voice) to omap3
McBSP ports in the following way:
HiFi <-> McBSP2
Voice <-> McBSP3
The zoom2 driver has the following DAPM widgets:
* Ext Mic: MAINMIC, SUBMIC (with bias)
* Ext Spk: HFL, HFR
* Headset Stereophone: HSOL, HSOR
* Headset Mic: HSMIC (with bias)
* Aux In: AUXL, AUXR
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
With this patch the initial headset pop-removal related values are
configured for the twl4030 codec (ramp delay and sysclk).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Connect twl4030 voice DAI to McBSP3 in sdp3430 machine driver.
Voice DAI init function enables corresponding interface by
writting directly to VOICE_IF codec register.
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Acked-by: Peter Ujflausi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Resending the patch after fixing the minor issues.
Signed-off-by: Anuj Aggarwal <anuj.aggarwal@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for the four channel TDM mode
on Beagle board.
Depending on the channel count, the interface needs to be
configured differently (I2S for stereo DSP_A for four channels)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add 4 channel support to omap-mcbsp.
This mode is going to be used by the twl4030 codec, when it
is configured in Option1 mode.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add checking in hw_params and prepare to detect bufferless pcms(i.e. BT
<--> codec).
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add Voice DAI to support the PCM voice interface of the twl4030 codec.
The PCM voice interface can be used with 8-kHz(voice narrowband) or
16-kHz(voice wideband) sampling rates, and 16bits, and mono RX and mono
TX or stereo TX.
The PCM voice interface has two modes
- PCM mode1 : This uses the normal FS polarity and the rising edge of
the clock signal.
- PCM mode2 : This uses the FS polarity inverted and the falling edge
of the clock signal.
If the system master clock is not 26MHz or the twl4030 codec mode is not
option2, the voice PCM interface is not available.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
My email address is going to expire soon so update it. Adding also
Peter Ujfalusi <peter.ujfalusi@nokia.com> as a second contact to OMAP core
drivers since I won't have anymore access to non-public OMAP documentation
in the future and Peter is working with these drivers as well.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Cc: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
DSP_A mode is similar to the DSP_B, but the MSB is delayed with
one bclk (appears after the FS pulse and not under it).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use single-phase mode for the DSP mode and keep the dual phase
mode for the I2S mode.
The mono (1 channel) mode already used single phase mode,
now it is more cleaner. There is no need to configure the
second phase, when the single phase is used.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Using inverted FS polarity in OSK5912 must be an error since TLV320AIC23
do not have support for inverted polarities. This is mostly due the hassle
with the DSP formats in OMAP McBSP DAI and inversion on OMAP side probably
just made this configuration working at some point.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Acked-by: Arun KS <arunks@mistralsolutions.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The DSP format wasn't still correct in OMAP McBSP DAI even after the commit
bd25867a6c.
Thanks to Peter Ujfalusi <peter.ujfalusi@nokia.com> for noticing and being
part of the fix. Now the FS length definition is more clear by defining
it with FWID(0).
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
McBSP2 in OMAP3 has 1 ksample (1k x 32 bit) internal FIFO. During
initial playback startup, this FIFO is keeping the DMA request active
until the FIFO is full.
So now if ALSA buffer size is smaller, DMA is looping around it while
filling up the HW FIFO, generating burst of interrupts as well and SW
doesn't have any change to fill enough data.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Headset was declared previously as a Headphone widget connecting
HSMIC and HSOL/HSOR pins of TWL4030 codec in SDP430 machine driver.
The capture path becomes invalid as the Headphone widget is not a
valid input endpoint.
Instead of that, the Headset is declared as separate Microphone
and Headphone widgets. Current patch modifies audio map:
- Headset Mic: HSMIC with bias
- Headset Stereophone: HSOL, HSOR
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add functions "Headset" and "Mic" to the control "Jack Function" for
activating and de-activating codec input pin LINE1L which is connected to
the mic pin of 4-pole Nokia AV connecter.
Note there is no mic bias voltage management here since bias is coming from
Nokia ASIC and driver for it is not in mainline.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Move headset jack registration to the codec/machine specific
initialization. Having the jack registration in machine init
causes that the jack device gets initialized but not registered
since the sound card is registered before the jack. Moving jack
registration to device initialization will register the jack
device along with all other devices associated to the card when
the card is registed. As a consequence of jack device registered
properly, the jack is detected as an input device.
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The drivers are basically duplicating the same code over and over.
As snd_soc_cnew is going to be made static some time after the next
merge window, we might as well convert them now.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Buildfix:
CC sound/soc/omap/osk5912.o
sound/soc/omap/osk5912.c: In function 'osk_soc_init':
sound/soc/omap/osk5912.c:189: error: implicit declaration of function 'clk_get_usecount'
make[3]: *** [sound/soc/omap/osk5912.o] Error 1
There's no such (standard) clock interface.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add headset jack detection for SDP3430 boards using SoC jack
reporting interface. Headset detection on SDP3430 board is
achieved through TWL4030 GPIO_2 pin.
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Considering the fact that most cpu_dai or codec_dai are using a same
'snd_soc_dai_ops' for several similar interfaces, 'ops' would be better
made a pointer instead, to make sharing easier and code a bit cleaner.
The patch below is rather preliminary since the asoc tree is being
actively developed, and this touches almost every piece of code,
(and possibly many others in development need to be changed as
well). Building of all codecs are OK, yet to every SoC, I didn't test
that.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch replaces "snd_soc_machine" structure by "snd_soc_card" in
SP3430 driver. This change is needed in SDP3430 driver to reflect
changes introduced by "ASoC: Rename snd_soc_card to snd_soc_machine" patch
(875065491f).
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
omap_pcm_trigger is called also in interrupt context so CPU flags must
be restored when returning.
Signed-off-by: Eero Nurkkala <ext-eero.nurkkala@nokia.com>
Acked-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Update pandora board file for recent TWL4030 codec changes.
Also move output related snd_soc_dapm_nc_pin() calls to
omap3pandora_out_init(), where they belong.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch explicitly initializes McBSP Transmit Configuration
Control Register (XCCR) and Receive Configuration Control
Register (RCCR) to their reset values. Reset values are 26 ns
of DX delay and Transmit DMA disabled for XCCR register;
receive full cycle mode enabled and Receive DMA disabled for
RCCR register.
This patch requires a counterpart in OMAP McBSP driver before
to apply it. The required changes in McBSP were sent and approved
in linux-omap mailing list and patch is going upstream
(commit 3127f8f859 from linux-omap-2.6
tree).
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
[ jarkko.nikula@nokia.com: Commit id for counterpart patch corrected ]
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Kbuild ignores dependency from things that are themselves selected so
ASoC machine drivers need to ensure that the control bus is being built.
This also avoids issues where multiple buses are supported by a given
codec.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit dc06102a0c in the asoc tree
did not include the necessary Kconfig and Makefile changes. This patch
completes the support for Beagleboard
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Acked-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The PCM operations tables are not exported directly but are instead
included in the platform structure so should be declared static.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Pandora has all TWL4030 output pins floating, it uses
external DAC for playback. Mark those outputs as not
connected using DAPM calls.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
N810 bootloader muxes I2S pins for OMAP2420 EAC block while N810 ASoC
drivers are using McBSP block so the kernel have to change configuration
runtime.
Author has not seen problems using kernel pin multiplexing on N810 but very
many times unworking audio after forgotten to enable it and spending
15 minutes each time to figure it out again...
This change makes it easier for other users as well. If problems arise, then
they are better to find and fix in OMAP pin multiplexing framework.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
- OMAP McBSP DAI driver claims to support DSP_A format which has 1-bit data
delay but configures link for 0-bit data delay which is in fact DSP_B
- Fix this by changing format from DSP_A to DSP_B
- Fix also TLV320AIC23 codec and OSK5912 machine drivers since the same
error is populated also there
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Acked-by: Arun KS <arunks@mistralsolutions.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There will be a Oops or frequent underrun messages when playing music with
omap soc driver, this is because a data region is incorretly sized, other data
region will be overwriten when writing to this data region.
Signed-off-by: Stanley Miao <stanley.miao@windriver.com>
Acked-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Cc: stable@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add snd_ prefix to avoid the conflict of symbols in omac-mcbsp.c:
sound/soc/omap/omap-mcbsp.c:503: error: static declaration of 'omap_mcbsp_init' follows non-static declaration
arch/arm/plat-omap/include/mach/mcbsp.h:373: error: previous declaration of 'omap_mcbsp_init' was here
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is done at modprobe time, mirroring current behaviour, except for
mpc5200_psc_i2s where we do registration at the same time as we register
with soc-of-simple. Since the core currently ignores registration this
has no practical impact.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Register all platform DAIs with the core. In line with current behaviour
this is done at module probe time rather than when the devices are probed
(since currently that only happens as the entire ASoC card is registered
except for those drivers that currently implement some kind of hotplug).
Since the core currently ignores DAI registration this has no practical
effect.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds basic support for OMAP3 Pandora.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
As part of the deprecation of snd_soc_device push the registration of
the platform down into the card structure.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The dependency on SND_SOC is already fulfilled in sound/soc/Kconfig,
thus no more need in Kconfig of each sub directory.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch add ASoC support for TI SDP3430. It's based on Gumstix
Overo SoC code by Steve Sakoman.
Signed-off-by: Misael Lopez Cruz <mesak82@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fixes Kconfig dependency of TWL4030 audio codec driver
with TWL4030 core driver on both overo and omap2evm
boards
Signed-off-by: Arun KS <arunks@mistralsolutions.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Patch adds support for mono audio links so that McBSP DAI can operate with
real mono codecs. In I2S, the signalling remains the same but only first
frame (left channel) is transmitting audio data and second frame having null
data. In DSP_A, only first frame is transmitted.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Prepare for upcoming McBSP DAI update adding support for mono links by
restricting number of channels to 2 in N810. This is due tlv320aic3x which
claims channels_min = 1 and playing pure mono audio over I2S would cause
it to be played only from left channel if both cpu and codec DAI's claim to
support mono.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lopez Cruz, Misael