With the support to bounce buffer added, the skb is coming as nonlinear in the
case of non-DDPed data frames for FCoE, which is mostly ok as the FCoE stack
would take care of that. However, for target mode, we have to set the FC CRC
and FC EOF field to allow the protocol stack to not drop the frame for the last
data frame of that sequence. So fix this by linearizing the skb first before
doing skb_put().
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Marcus Dennis <marcusx.e.dennis@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver was freeing memory in shutdown instead of remove. As a result
we were leaking memory if IEEE DCB was enabled and we loaded/unloaded the
driver. This change moves the freeing of the memory into the remove
routine where it belongs.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Maybe it's a typo, but it cause that igbvf can't be initialized successfully.
Set perm_addr value using valid dev_addr, although which is equal to hw.mac.addr.
Signed-off-by: Samuel Liao <samuelliao@tencent.com>
Signed-off-by: Shan Wei <davidshan@tencent.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch sets the automatic speed and duplex detection bits
in MAC_CR to enable the mac to determine its speed automatically
from the phy.
Note this must be done BEFORE the receiver or transmitter is
enabled.
Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
also explicitly set the phy to advertise 1000 speeds
Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
smsc75xx phy interrupt acknowledge needs an mdio_write to clear
PHY_INT_SRC instead of just a read like in smsc95xx.
Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix bug in phy_init loop that was ignoring BMCR reset bit, akin to smsc95xx's d946092000
Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
smsc75xx needs MII_ACCESS_BUSY to be set to correctly trigger mdio I/O. Note smsc75xx is different from smsc95xx in this regard.
Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the same issue as reported on smsc95xx, where the
usb device is connected with no ethernet cable plugged-in.
Without this patch sysfs reports the cable as present
flag@flag-desktop:~$ cat /sys/class/net/eth0/carrier
1
while it's not:
flag@flag-desktop:~$ sudo mii-tool eth0
eth0: no link
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
As s3c2412-i2s is using the s3c_i2sv2 it should call the more specialised
s3c_i2sv2_register_dai instead of simply calling snd_soc_register_dai.
Without this call the snd_soc_dai_ops structure isn't initialised correctly.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The core allocates the live copies, we shouldn't try to duplicate it and
were buggy trying to do so as we were using uninitialised data for the
control data.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Pull ARM fixes from Russell King.
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7406/1: hotplug: copy the affinity mask when forcefully migrating IRQs
ARM: 7405/1: kexec: call platform_cpu_kill on the killer rather than the victim
ARM: 7403/1: tls: remove covert channel via TPIDRURW
ARM: 7401/1: mm: Fix section mismatches
ARM: OMAP: fix DMA vs memory ordering
ARM: 7390/1: dts: versatile-pb/ab fix MMC IRQs
ARM: 7400/1: vfp: clear fpscr length and stride bits on entry to sig handler
ARM: 7399/1: vfp: move user vfp state save/restore code out of signal.c
ARM: 7398/1: l2x0: only write to debug registers on PL310
ARM: 7397/1: l2x0: only apply workaround for erratum #753970 on PL310
ARM: 7396/1: errata: only handle ARM erratum #326103 on affected cores
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPnjtXAAoJEDeqqVYsXL0MNWkIAMYc5n06Ac/gdLY8xIIYD6GA
OzLd/NQ2Q4RqZJsX26OueX2ZjMRYDixBAmiw837K9PvrLUHGfMAaninNyzDgVZ3R
pbIK45OylIQrvMAl/R7ZzqihfxJjg5utqEUt1M2qv/ikkBJ8+zWAJTQKxRYJ1OAW
9QDhIP986hljNyZfDuqXBvA4XkngYeCO0WLjBOeYCseSzeV8vOLpmsD/ANHDcqA6
Ct4uM4KJWF4jHz3sN3w5T3morNwvh42onNcy++911HcH5Nc9bkOqBWQAZ5RtINp9
8rkUz3OtCCQpZz6ffF3ZXJaopuU3ELfP80t03OScr2T75SxLqLf6mFYVAcR7RpQ=
=nXrE
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of SAS and SATA fixes; there are one or two longstanding
bug fixes, but most of this is regression fixes."
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] libfc: update mfs boundry checking
[SCSI] Revert "[SCSI] libsas: fix sas port naming"
[SCSI] libsas: fix false positive 'device attached' conditions
[SCSI] libsas, libata: fix start of life for a sas ata_port
[SCSI] libsas: fix ata_eh clobbering ex_phys via smp_ata_check_ready
[SCSI] libsas: unify domain_device sas_rphy lifetimes
[SCSI] libsas: fix sas_get_port_device regression
[SCSI] libsas: fix sas_find_bcast_phy() in the presence of 'vacant' phys
[SCSI] libsas: introduce sas_work to fix sas_drain_work vs sas_queue_work
[SCSI] libata: Pass correct DMA device to scsi host
[SCSI] scsi_lib: use correct DMA device in __scsi_alloc_queue
A common flaw in UEFI systems is a refusal to POST triggered by a malformed
boot variable. Once in this state, machines may only be restored by
reflashing their firmware with an external hardware device. While this is
obviously a firmware bug, the serious nature of the outcome suggests that
operating systems should filter their variable writes in order to prevent
a malicious user from rendering the machine unusable.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
More recent versions of the UEFI spec have added new attributes for
variables. Add them.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
sh_symtab is set but not used.
[ hpa: putting this in urgent because of the sheer harmlessness of the patch:
it quiets a build warning but does not change any generated code. ]
Signed-off-by: Kusanagi Kouichi <slash@ac.auone-net.jp>
Link: http://lkml.kernel.org/r/20120401082932.D5E066FC03D@msa105.auone-net.jp
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: <stable@vger.kernel.org>
<asm-generic/statfs.h> is exported to userspace, so using
BITS_PER_LONG is invalid. We need to use __BITS_PER_LONG instead.
This is kernel bugzilla 43165.
Reported-by: H.J. Lu <hjl.tools@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Link: http://lkml.kernel.org/r/1335465916-16965-1-git-send-email-hpa@linux.intel.com
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: <stable@vger.kernel.org>
Fix printk format warnings -- both items are size_t,
so use %zu to print them.
fs/nfsd/nfs4recover.c:580:3: warning: format '%lu' expects type 'long unsigned int', but argument 3 has type 'size_t'
fs/nfsd/nfs4recover.c:580:3: warning: format '%lu' expects type 'long unsigned int', but argument 4 has type 'unsigned int'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: linux-nfs@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
EAP frames for stations in an AP VLAN are sent on the main AP interface
to avoid race conditions wrt. moving stations.
For that to work properly, sta_info_get_bss must be used instead of
sta_info_get when sending EAP packets.
Previously this was only done for cooked monitor injected packets, so
this patch adds a check for tx->skb->protocol to the same place.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The O_DIRECT code shouldn't need to hold 2 references to each page. The
reference held by the struct nfs_page should suffice.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: Fred Isaman <iisaman@netapp.com>
Currently we do break out of the for() loop, but we also need to
break out of the enclosing do {} while()...
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: Fred Isaman <iisaman@netapp.com>
These are needed when v3 and v4 are not enabled.
Signed-off-by: Bryan Schumaker <bjschuma@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
v2 doesn't have commits, so this function can be a no-op.
Signed-off-by: Bryan Schumaker <bjschuma@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Pull powerpc fixes from Benjamin Herrenschmidt:
"Here are a handful more fixes for powerpc. The irq stuff are all
regression fixes, and Gavin's patch is a simple compile fix."
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
tty/serial/pmac_zilog: Fix "nobody cared" IRQ message
powerpc/pseries: Rivet CONFIG_EEH for pSeries platform
powerpc/irqdomain: Fix broken NR_IRQ references
powerpc/8xx: Fix NR_IRQ bugs and refactor 8xx interrupt controller
This is only when CONFIG_NFS_V4_1 isn't enabled.
Signed-off-by: Bryan Schumaker <bjschuma@netapp.com>
Acked-by: Fred Isaman <iisaman@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
When the cwnd reduction is done, ssthresh may be infinite
if TCP enters CWR via ECN or F-RTO. If cwnd is not undone, i.e.,
undo_marker is set, tcp_complete_cwr() falsely set cwnd to the
infinite ssthresh value. The correct operation is to keep cwnd
intact because it has been updated in ECN or F-RTO.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now the helper function from filter.c for negative offsets is exported,
it can be used it in the jit to handle negative offsets.
First modify the asm load helper functions to handle:
- know positive offsets
- know negative offsets
- any offset
then the compiler can be modified to explicitly use these helper
when appropriate.
This fixes the case of a negative X register and allows to lift
the restriction that bpf programs with negative offsets can't
be jited.
Tested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jan Seiffert <kaffeemonster@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull input fix from Dmitry Torokhov:
"A simple fix for a recent regression in Synaptics driver"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: synaptics - fix regression with "image sensor" trackpads
We need to use the hostname of the process that created the nfs_client.
That hostname is now stored in the rpc_client->cl_nodename.
Also remove the utsname()->domainname component. There is no reason
to include the NIS/YP domainname in a client identifier string.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Now that the rpc client is namespace aware, it needs to use the
utsname of the process that created it instead of using the
init_utsname. Both rpc_new_client and rpc_clone_client need to
be fixed.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: Stanislav Kinsbursky <skinsbursky@parallels.com>
* commit f9dfbf9 "ASoC: tlv320aic23: convert to soc-cache" leads to
a bug preventing resumeof the codec as regmap expects a 9 bits data
register but 0xFFFF is passed in tlv320aic23_set_bias_level and this
values gets cached preventing any write to the TLV320AIC23_PWR
register as the final value produced by regmap is (register << 9) | value
* this patch solves the problem by only working on the 9 bits the
register contains.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
The current checking always succeeded. We have to check the first
character of the string to check that it's empty, thus, skipping
the timeout path.
This fixes the use of the CT target without the timeout option.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Change order of init so netns init is ready
when register ioctl and netlink.
Ver2
Whitespace fixes and __init added.
Reported-by: "Ryan O'Hara" <rohara@redhat.com>
Signed-off-by: Hans Schillstrom <hans.schillstrom@ericsson.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
ip_vs_create_timeout_table() can return NULL
All functions protocol init_netns is affected of this patch.
Signed-off-by: Hans Schillstrom <hans.schillstrom@ericsson.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Avoid crash when registering shedulers after
the IPVS core initialization for netns fails. Do this by
checking for present core (net->ipvs).
Signed-off-by: Hans Schillstrom <hans.schillstrom@ericsson.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
We started using the connector table on nv4x a while back, and this VBIOS
has bad connector indices which causes the wrong encoders to get paired
with connectors.
Add a quirk to fix this...
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Recently, Ryan Wang tried to compile PPC pSeries platform without
CONFIG_EEH and eventually run into errors. Nishanth Aravamudan
helped to narrow down the root cause. Actually, the pSeries platform
depends on CONFIG_EEH heavily and that won't work properly without
EEH support.
According to Ben's suggestion, the patch make CONFIG_EEH invisible
and keep it as always selected on pSeries platform.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The switch from using irq_map to irq_alloc_desc*() for managing irq
number allocations introduced new bugs in some of the powerpc
interrupt code. Several functions rely on the value of NR_IRQS to
determine the maximum irq number that could get allocated. However,
with sparse_irq and using irq_alloc_desc*() the maximum possible irq
number is now specified with 'nr_irqs' which may be a number larger
than NR_IRQS. This has caused breakage on powermac when
CONFIG_NR_IRQS is set to 32.
This patch removes most of the direct references to NR_IRQS in the
powerpc code and replaces them with either a nr_irqs reference or by
using the common for_each_irq_desc() macro. The powerpc-specific
for_each_irq() macro is removed at the same time.
Also, the Cell axon_msi driver is refactored to remove the global
build assumption on the size of NR_IRQS and instead add a limit to the
maximum irq number when calling irq_domain_add_nomap().
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The mpc8xx driver uses a reference to NR_IRQS that is buggy. It uses
NR_IRQs for the array size of the ppc_cached_irq_mask bitmap, but
NR_IRQs could be smaller than the number of hardware irqs that
ppc_cached_irq_mask tracks.
Also, while fixing that problem, it became apparent that the interrupt
controller only supports 32 interrupt numbers, but it is written as if
it supports multiple register banks which is more complicated.
This patch pulls out the buggy reference to NR_IRQs and fixes the size
of the ppc_cached_irq_mask to match the number of HW irqs. It also
drops the now-unnecessary code since ppc_cached_irq_mask is no longer
an array.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
David S. Miller