Since the only way the interface can be a monitor
interface in ieee80211_xmit() is because the frame
came from ieee80211_monitor_start_xmit() we can
move all the code there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add documentation about NOACK tx flag usage.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When tx is suspended temporarily and the queue is flushed, do not increase
the retry count or attempt to send out BAR frames. Instead simply retry
the affected subframes normally after the reset.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do not increment the retry counter if packets to a sleeping station
were not sent because of tx failure, instead of only checking the filter
flag.
Clear the PS filter only after an A-MPDU was reported as filtered,
otherwise the hardware might do some unnecessary extra retransmissions.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Export how many times each of the reset triggers has fired through debugfs.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mesh paths should only exist over established peer links.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If "axq_qnum >= ARRAY_SIZE(sc->tx.txq)", then the call to
ath9k_hw_releasetxqueue() would read beyond the end of the ah->txq[]
array and possibly corrupt memory. Fortunately,
ath9k_hw_setuptxqueue() doesn't return high values of "axq_qnum" and
this code can be removed.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
th5k_hw_setup_tx_queue() returns a valid offset into the ah->ah_txq[]
array. The ah->ah_txq[] and the ah->txqs[] array are the same size.
Both have AR5K_NUM_TX_QUEUES elements. So this error handling code
will never trigger.
Also it's wrong. The call to ath5k_hw_release_tx_queue() with a qnum
of AR5K_NUM_TX_QUEUES or more will just trigger a WARN_ON() and
return. Or if it missed the WARN_ON(), it would just corrupt some
memory and return.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When I introduced in-kernel off-channel TX I
introduced a bug -- the work can't be canceled
again because the code clear the skb pointer.
Fix this by keeping track separately of whether
TX status has already been reported.
Cc: stable@kernel.org [2.6.38+]
Reported-by: Jouni Malinen <j@w1.fi>
Tested-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
My previous patch for init calib cfg disable a set of calibration for both
init and runtime which cause performance issue, Fix it
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is needed so that offloaded scan can do the
right thing. Without this patch, the no_cck flag
contains random values from the kernel heap.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the brcm80211 tree to drivers/net/wireless, and disable the version that's
in drivers/staging. This version includes the sources currently in staging,
plus any changes that have been sent out for review.
Sources in staging will be deleted in a followup patch.
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CC [M] drivers/net/wireless/ath/ath6kl/cfg80211.o
drivers/net/wireless/ath/ath6kl/cfg80211.c:1838:2: warning: initialization from incompatible pointer type
Caused by commit e9f935e3e8dc0bddd0df6d148165d95925422502...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Breno Leitao <leitao@linux.vnet.ibm.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
If skb is NULL, then stack trace is thrown anyway on dereference.
Therefore, the stack trace triggered by BUG_ON is duplicate.
Signed-off-by: Daniel Borkmann <danborkmann@googlemail.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joe reported to me that right after a bring up of a r6040 interface
the ethtool output had no consistent output with respect to link duplex
and speed. Fix this by adding a missing phy_start call in r6040_up and
conversely a phy_stop call in r6040_down to properly initialize phy states.
Reported-by: Joe Chou <Joe.Chou@rdc.com.tw>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Query port will now identify a 40G Ethernet speed.
Signed-off-by: Alexander Guller <alexg@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Netdevice was being freed without being unregistered first if
mlx4_SET_PORT_general or mlx4_INIT_PORT failed.
Signed-off-by: Alexander Guller <alexg@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Number of bits taken from mac table index in QP
calculation should be based on log_num_mac parameter.
Signed-off-by: Alexander Guller <alexg@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed a memory leak caused by missing iounmap when device
is being released.
Signed-off-by: Alexander Guller <alexg@mellanox.co.il>
Signed-off-by: Sharon Cohen <sharonc@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moderation is now done per ring and coalescing is enabled
by set_ring_param in ethtool.
Signed-off-by: Alexander Guller <alexg@mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed a bug where ring size change caused insufficient memory
upon driver restart due to unreleased EQs.
Signed-off-by: Alexander Guller <alexg@mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now only RX rings used irq per ring
and TX used only one per port.
>From now on, both of them will use the
irq per ring while RX & TX ring[i] will
use the same irq.
Signed-off-by: Alexander Guller <alexg@mellanox.co.il>
Signed-off-by: Sharon Cohen <sharonc@mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for Rx hashing.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change moves the Tx hang check into the ring flags.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch cleans up several issues with VLANs on igb after the recent
changes that were meant to leave the VLANs enabled/disable via the
netdev->features flags.
Specifically the Rx VLAN settings were being dropped after reset due to the
fact that they were not being restored correctly. In addition I removed
the IRQ disable/enable since those were in place to protect the setting of
vlgrp.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of doing a byte swap on the staterr bits in the Rx descriptor we can
save ourselves a bit of space and some CPU time by instead just testing for
the various bits out of the Rx descriptor directly.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since the netdev now has its' own checksum flag to indicate if Rx checksum
is enabled we might as well use that instead of using the ring flag.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to cleanup some of the IVAR register configuration.
igb_assign_vector had become pretty large with multiple copies of the same
general code for setting the IVAR. This change consolidates most of that
code by adding the igb_write_ivar function which allows us just to compute
the index and offset and then use that information to setup the IVAR.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change moves information related to interrupt throttle rate
configuration into a separate q_vector sub-structure called a work
container. A similar change has already been made for ixgbe and this work
is based off of that.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change moves all of the ring flags into a single value. The advantage
to this is that there is one central area for all of these flags and they
can all make use of the set/test bit operations.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are a number of places where we have values that are stored as u16
but are being converted to int unnecessarily. In order to avoid that we
should convert all variables that deal with the next_to_clean, next_to_use,
and count to u16 values.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to update the ring and vector allocations so that they
are per node instead of allocating everything on the node that
ifconfig/modprobe is called on. By doing this we can cut down
significantly on cross node traffic.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of storing most of the data for the TX hot path in the stack until
we are ready to write the descriptor we can save ourselves some time and
effort by pushing the SKB, tx_flags, gso_size, bytecount, and protocol into
the first igb_tx_buffer since that is where we will end up putting it
anyway.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Per comments from Ben Hutchings on a previous patch, sweep the floors
a little removing unnecessary assignments of zero to fields of struct
ethtool_ringparam in driver code supporting ethtool -g.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for reporting ring sizes via ethtool -g to the 8139cp driver.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no point in open-coding sock_valbool_flag().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change will combine the writes of tx_buffer_info and the Tx data
descriptors into a single function. The advantage of this is that we can
avoid needless memory reads from the buffer info struct and speed things up
by keeping the accesses to the local registers.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Johannes Berg