Bastian Blank reported a boot crash with stackprotector enabled,
and debugged it back to edx register corruption.
For historical reasons irq enable/disable/save/restore had special
calling sequences to make them more efficient. With the more
recent introduction of higher-level and more general optimisations
this is no longer necessary so we can just use the normal PVOP_
macros.
This fixes some residual bugs in the old implementations which left
edx liable to inadvertent clobbering. Also, fix some bugs in
__PVOP_VCALLEESAVE which were revealed by actual use.
Reported-by: Bastian Blank <bastian@waldi.eu.org>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stable Kernel <stable@kernel.org>
Cc: Xen-devel <xen-devel@lists.xensource.com>
LKML-Reference: <4AD3BC9B.7040501@goop.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
this is needed for kvm if it want ksm to directly map pages into its
shadow page tables.
[marcelo: cast pfn assignment to u64]
Signed-off-by: Izik Eidus <ieidus@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Make decoding of MCEs happen only on AMD hardware by registering a
non-default callback only on CPU families which support it.
While looking at the interaction of decode_mce() with the other MCE
code i also noticed a few other things and made the following
cleanups/fixes:
- Fixed the mce_decode() weak alias - a weak alias is really not
good here, it should be a proper callback. A weak alias will be
overriden if a piece of code is built into the kernel - not
good, obviously.
- The patch initializes the callback on AMD family 10h and 11h.
- Added the more correct fallback printk of:
No support for human readable MCE decoding on this CPU type.
Transcribe the message and run it through 'mcelog --ascii' to decode.
On CPUs that dont have a decoder.
- Made the surrounding code more readable.
Note that the callback allows us to have a default fallback -
without having to check the CPU versions during the printout
itself. When an EDAC module registers itself, it can install the
decode-print function.
(there's no unregister needed as this is core code.)
version -v2 by Borislav Petkov:
- add K8 to the set of supported CPUs
- always build in edac_mce_amd since we use an early_initcall now
- fix checkpatch warnings
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andi Kleen <andi@firstfloor.org>
LKML-Reference: <20091001141432.GA11410@aftab>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Just like ip_fast_csum, the assembly snippet in csum_ipv6_magic needs a
memory clobber, as it is only passed the address of the buffer, not a
memory reference to the buffer itself.
This caused failures in Hurd's pfinetv4 when we tried to compile it with
gcc-4.3 (bogus checksums).
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: "David S. Miller" <davem@davemloft.net>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Just like ip_fast_csum, the assembly snippet in csum_ipv6_magic needs a
memory clobber, as it is only passed the address of the buffer, not a
memory reference to the buffer itself.
This caused failures in Hurd's pfinetv4 when we tried to compile it with
gcc-4.3 (bogus checksums).
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
cmpxchg64() today generates, to quote Linus, "barf bag" code.
cmpxchg64() is about to get used in the scheduler to fix a bug there,
but it's a prerequisite that cmpxchg64() first be made non-sucking.
This patch turns cmpxchg64() into an efficient implementation that
uses the alternative() mechanism to just use the raw instruction on
all modern systems.
Note: the fallback is NOT smp safe, just like the current fallback
is not SMP safe. (Interested parties with i486 based SMP systems
are welcome to submit fix patches for that.)
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
[ fixed asm constraint bug ]
Fixed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: John Stultz <johnstul@us.ibm.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <20090930170754.0886ff2e@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
It's unused.
It isn't needed -- read or write flag is already passed and sysctl
shouldn't care about the rest.
It _was_ used in two places at arch/frv for some reason.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: David Howells <dhowells@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
arch/x86/include/asm/topology.h declares inline fns cpu_to_node and
cpumask_of_node for !NUMA, even though they are then declared as
macros by asm-generic/topology.h, which is #included just below.
The macros (which are the same) end up being used; these functions
are just confusing.
Noticed-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: "Greg Kroah-Hartman" <gregkh@suse.de>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Tejun Heo <tj@kernel.org>
LKML-Reference: <200909241748.45629.rusty@rustcorp.com.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Makes code futureproof against the impending change to mm->cpu_vm_mask (to be a pointer).
It's also a chance to use the new cpumask_ ops which take a pointer
(the older ones are deprecated, but there's no hurry for arch code).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Move the NX setup into a separate file so that it can be compiled
without stack-protection while leaving the rest of the mm/init code
protected.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Bye-bye Performance Counters, welcome Performance Events!
In the past few months the perfcounters subsystem has grown out its
initial role of counting hardware events, and has become (and is
becoming) a much broader generic event enumeration, reporting, logging,
monitoring, analysis facility.
Naming its core object 'perf_counter' and naming the subsystem
'perfcounters' has become more and more of a misnomer. With pending
code like hw-breakpoints support the 'counter' name is less and
less appropriate.
All in one, we've decided to rename the subsystem to 'performance
events' and to propagate this rename through all fields, variables
and API names. (in an ABI compatible fashion)
The word 'event' is also a bit shorter than 'counter' - which makes
it slightly more convenient to write/handle as well.
Thanks goes to Stephane Eranian who first observed this misnomer and
suggested a rename.
User-space tooling and ABI compatibility is not affected - this patch
should be function-invariant. (Also, defconfigs were not touched to
keep the size down.)
This patch has been generated via the following script:
FILES=$(find * -type f | grep -vE 'oprofile|[^K]config')
sed -i \
-e 's/PERF_EVENT_/PERF_RECORD_/g' \
-e 's/PERF_COUNTER/PERF_EVENT/g' \
-e 's/perf_counter/perf_event/g' \
-e 's/nb_counters/nb_events/g' \
-e 's/swcounter/swevent/g' \
-e 's/tpcounter_event/tp_event/g' \
$FILES
for N in $(find . -name perf_counter.[ch]); do
M=$(echo $N | sed 's/perf_counter/perf_event/g')
mv $N $M
done
FILES=$(find . -name perf_event.*)
sed -i \
-e 's/COUNTER_MASK/REG_MASK/g' \
-e 's/COUNTER/EVENT/g' \
-e 's/\<event\>/event_id/g' \
-e 's/counter/event/g' \
-e 's/Counter/Event/g' \
$FILES
... to keep it as correct as possible. This script can also be
used by anyone who has pending perfcounters patches - it converts
a Linux kernel tree over to the new naming. We tried to time this
change to the point in time where the amount of pending patches
is the smallest: the end of the merge window.
Namespace clashes were fixed up in a preparatory patch - and some
stylistic fallout will be fixed up in a subsequent patch.
( NOTE: 'counters' are still the proper terminology when we deal
with hardware registers - and these sed scripts are a bit
over-eager in renaming them. I've undone some of that, but
in case there's something left where 'counter' would be
better than 'event' we can undo that on an individual basis
instead of touching an otherwise nicely automated patch. )
Suggested-by: Stephane Eranian <eranian@google.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Paul Mackerras <paulus@samba.org>
Reviewed-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: <linux-arch@vger.kernel.org>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch changes the remaining direct references to
.data.page_aligned in C and assembly code to use the macros in
include/linux/linkage.h.
Signed-off-by: Tim Abbott <tabbott@ksplice.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Cc: Vegard Nossum <vegardno@ifi.uio.no>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Alok N Kataria <akataria@vmware.com>
Cc: "Tan Wei Chong" <wei.chong.tan@intel.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Lin Ming <ming.m.lin@intel.com>
Cc: Bob Moore <robert.moore@intel.com>
LKML-Reference: <1253137123-18047-2-git-send-email-felipe.contreras@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In case of discrete (pretty old) apics we may have cpu_has_apic bit
not set but have to check if smp_found_config (MP spec) is there
and apic was not disabled.
Also don't forget to print apic/io-apic for such case as well.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: "Maciej W. Rozycki" <macro@linux-mips.org>
Cc: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <20090915071230.GA10604@lenovo>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The early initialization of the pci bus to node mapping leaves all busses
with a node id of -1 if it lacks memory affinity. Thus, cpumask_of_pcibus
must return all online cpus for such busses.
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Add volatile-semantics to the SGI UV read/write macros that are
used to access chipset memory mapped registers. No direct
references to volatile are made. Instead the readq/writeq macros
are used.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Cc: linux-mm@kvack.org
Cc: dwalker@fifo99.com
Cc: cfriesen@nortel.com
LKML-Reference: <20090910143149.GA14273@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The UV BIOS has changed the way interrupt remapping is being done.
This affects the id used for sending IPIs. The upper id bits no
longer need to be masked off.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Cc: <stable@kernel.org>
LKML-Reference: <20090909154104.GA25083@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Sysbench thinks SD_BALANCE_WAKE is too agressive and kbuild doesn't
really mind too much, SD_BALANCE_NEWIDLE picks up most of the
slack.
On a dual socket, quad core, dual thread nehalem system:
sysbench (--num_threads=16):
SD_BALANCE_WAKE-: 13982 tx/s
SD_BALANCE_WAKE+: 15688 tx/s
kbuild (-j16):
SD_BALANCE_WAKE-: 47.648295846 seconds time elapsed ( +- 0.312% )
SD_BALANCE_WAKE+: 47.608607360 seconds time elapsed ( +- 0.026% )
(same within noise)
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
get/set_wallclock() have already a set of platform dependent
implementations (default, EFI, paravirt). MRST will add another
variant.
Moving them to platform ops simplifies the existing code and minimizes
the effort to integrate new variants.
Signed-off-by: Feng Tang <feng.tang@intel.com>
LKML-Reference: <new-submission>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Move some of the aperf/mperf code out from the cpufreq driver
thingy so that other people can enjoy it too.
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Yanmin <yanmin_zhang@linux.intel.com>
Cc: Dave Jones <davej@redhat.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: cpufreq@vger.kernel.org
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Move the APERFMPERF capacility into a X86_FEATURE flag so that it
can be used outside of the acpi cpufreq driver.
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Yanmin <yanmin_zhang@linux.intel.com>
Cc: Dave Jones <davej@redhat.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: cpufreq@vger.kernel.org
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
If we're looking to place a new task, we might as well find the
idlest position _now_, not 1 tick ago.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Make the idle balancer more agressive, to improve a
x264 encoding workload provided by Jason Garrett-Glaser:
NEXT_BUDDY NO_LB_BIAS
encoded 600 frames, 252.82 fps, 22096.60 kb/s
encoded 600 frames, 250.69 fps, 22096.60 kb/s
encoded 600 frames, 245.76 fps, 22096.60 kb/s
NO_NEXT_BUDDY LB_BIAS
encoded 600 frames, 344.44 fps, 22096.60 kb/s
encoded 600 frames, 346.66 fps, 22096.60 kb/s
encoded 600 frames, 352.59 fps, 22096.60 kb/s
NO_NEXT_BUDDY NO_LB_BIAS
encoded 600 frames, 425.75 fps, 22096.60 kb/s
encoded 600 frames, 425.45 fps, 22096.60 kb/s
encoded 600 frames, 422.49 fps, 22096.60 kb/s
Peter pointed out that this is better done via newidle_idx,
not via LB_BIAS, newidle balancing should look for where
there is load _now_, not where there was load 2 ticks ago.
Worst-case latencies are improved as well as no buddies
means less vruntime spread. (as per prior lkml discussions)
This change improves kbuild-peak parallelism as well.
Reported-by: Jason Garrett-Glaser <darkshikari@gmail.com>
Signed-off-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1253011667.9128.16.camel@marge.simson.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When merging select_task_rq_fair() and sched_balance_self() we lost
the use of wake_idx, restore that and set them to 0 to make wake
balancing more aggressive.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The problem with wake_idle() is that is doesn't respect things like
cpu_power, which means it doesn't deal well with SMT nor the recent
RT interaction.
To cure this, it needs to do what sched_balance_self() does, which
leads to the possibility of merging select_task_rq_fair() and
sched_balance_self().
Modify sched_balance_self() to:
- update_shares() when walking up the domain tree,
(it only called it for the top domain, but it should
have done this anyway), which allows us to remove
this ugly bit from try_to_wake_up().
- do wake_affine() on the smallest domain that contains
both this (the waking) and the prev (the wakee) cpu for
WAKE invocations.
Then use the top-down balance steps it had to replace wake_idle().
This leads to the dissapearance of SD_WAKE_BALANCE and
SD_WAKE_IDLE_FAR, with SD_WAKE_IDLE replaced with SD_BALANCE_WAKE.
SD_WAKE_AFFINE needs SD_BALANCE_WAKE to be effective.
Touch all topology bits to replace the old with new SD flags --
platforms might need re-tuning, enabling SD_BALANCE_WAKE
conditionally on a NUMA distance seems like a good additional
feature, magny-core and small nehalem systems would want this
enabled, systems with slow interconnects would not.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Currently we are not including randomized stack size when calculating
mmap_base address in arch_pick_mmap_layout for topdown case. This might
cause that mmap_base starts in the stack reserved area because stack is
randomized by 1GB for 64b (8MB for 32b) and the minimum gap is 128MB.
If the stack really grows down to mmap_base then we can get silent mmap
region overwrite by the stack values.
Let's include maximum stack randomization size into MIN_GAP which is
used as the low bound for the gap in mmap.
Signed-off-by: Michal Hocko <mhocko@suse.cz>
LKML-Reference: <1252400515-6866-1-git-send-email-mhocko@suse.cz>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Stable Team <stable@kernel.org>
As reported in <http://bugs.debian.org/511703> and
<http://bugs.debian.org/515982>, kernels with paravirt-alternatives
enabled crash in text_poke_early() on at least some 486-class
processors.
The problem is that text_poke_early() itself uses inline functions
affected by paravirt-alternatives and so will modify instructions that
have already been prefetched. Pentium and later processors will
invalidate the prefetched instructions in this case, but 486-class
processors do not.
Change sync_core() to limit prefetching on 486-class (and 386-class)
processors, and move the call to sync_core() above the call to the
modifiable local_irq_restore().
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
LKML-Reference: <1252547631.3423.134.camel@localhost>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The dynamic function tracer relys on the macro P6_NOP5 always being
an atomic NOP. If for some reason it is changed to be two operations
(like a nop2 nop3) it can faults within the kernel when the function
tracer modifies the code.
This patch adds a comment to note that the P6_NOPs are expected to
be atomic. This will hopefully prevent anyone from changing that.
Reported-by: Mathieu Desnoyer <mathieu.desnoyers@polymtl.ca>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Debug registers may only be accessed from cpl 0. Unfortunately, vmx will
code to emulate the instruction even though it was issued from guest
userspace, possibly leading to an unexpected trap later.
Cc: stable@kernel.org
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Instead of saving the debug registers from the processor to a kvm data
structure, rely in the debug registers stored in the thread structure.
This allows us not to save dr6 and dr7.
Reduces lightweight vmexit cost by 350 cycles, or 11 percent.
Signed-off-by: Avi Kivity <avi@redhat.com>
If userspace knows that the kernel part supports 1GB pages it can enable
the corresponding cpuid bit so that guests actually use GB pages.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch adds support for shadow paging to the 1gb page table code in KVM.
With this code the guest can use 1gb pages even if the host does not support
them.
[ Marcelo: fix shadow page collision on pmd level if a guest 1gb page is mapped
with 4kb ptes on host level ]
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Now KVM allow guest to modify guest's physical address of EPT's identity mapping page.
(change from v1, discard unnecessary check, change ioctl to accept parameter
address rather than value)
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Remove kvm_cpu_has_interrupt() and kvm_arch_interrupt_allowed() from
interface between general code and arch code. kvm_arch_vcpu_runnable()
checks for interrupts instead.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
When kvm is in hpet_legacy_mode, the hpet is providing the timer
interrupt and the pit should not be. So in legacy mode, the pit timer
is destroyed, but the *state* of the pit is maintained. So if kvm or
the guest tries to modify the state of the pit, this modification is
accepted, *except* that the timer isn't actually started. When we exit
hpet_legacy_mode, the current state of the pit (which is up to date
since we've been accepting modifications) is used to restart the pit
timer.
The saved_mode code in kvm_pit_load_count temporarily changes mode to
0xff in order to destroy the timer, but then restores the actual
value, again maintaining "current" state of the pit for possible later
reenablement.
[avi: add some reserved storage in the ioctl; make SET_PIT2 IOW]
[marcelo: fix memory corruption due to reserved storage]
Signed-off-by: Beth Kon <eak@us.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Directed EOI is specified by x2APIC, but is available even when lapic is
in xAPIC mode.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This allows use of the powerful ftrace infrastructure.
See Documentation/trace/ for usage information.
[avi, stephen: various build fixes]
[sheng: fix control register breakage]
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Jeremy Fitzhardinge