Delay clean-up of last Tx packet to fix pre-mature writeback issue of Tx descriptors only when TSO is enabled
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
diff -up net-drivers-2.6/drivers/net/e1000/e1000_main.c net-drivers-2.6/drivers/net/e1000.new/e1000_main.c
Fix kernel panic with 82541 LOM when using a 100M cable
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
diff -up net-drivers-2.6/drivers/net/e1000/e1000_main.c net-drivers-2.6/drivers/net/e1000.new/e1000_main.c
Enable polling before enabling interrupts -- avoids (in NAPI mode) entering the ISR and returning without doing any work because polling is not enabled. [romieu@fr.zoriel.com]
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
diff -up net-drivers-2.6/drivers/net/e1000/e1000_main.c net-drivers-2.6/drivers/net/e1000.new/e1000_main.c
Fix msec-delay definition in e1000_osdep.h to use msleep
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
diff -up net-drivers-2.6/drivers/net/e1000/e1000_osdep.h net-drivers-2.6/drivers/net/e1000.new/e1000_osdep.h
Added enhanced functionality to the loopback diags to wrap the descriptor rings.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
diff -up net-drivers-2.6/drivers/net/e1000/e1000_ethtool.c net-drivers-2.6/drivers/net/e1000.new/e1000_ethtool.c
Add support to sis900 for the following ethtool ops:
- get_link
- get_settings
- set_settings
- nway_reset
Signed-off-by: Daniele Venzano <webvenza@libero.it>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch makes the netif_rx_complete() and rx_interrupt_enable
atomic when exiting the poll() method, so to avoid interrupt in poll.
It also fixes the rx interrupt check logic in interrupt handler.
Signed-off-by: Liu Tao <liutao1980@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Patch from Ben Dooks
Fix the setting of hdiv when set to divide-by-2. Thanks to
Jeonghoon Yoon for pointing this out.
Change name of the NAND device to "s3c2440-nand" as it
is not similar enough to the "s3c2410-nand" device.
Signed-off-by: Ben Dooks
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
S3C2440 UPLL is the same as the S3C2410 UPLL, it is only the
MPLL which has an extra multiplication factor of 2 in the
multiplier.
Signed-off-by: Ben Dooks
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Add the register definitions for the s3c2440 NAND controller
to the s3c2410 NAND register definitions
Signed-off-by: Ben Dooks
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
Not all ARMv6 processors implement the TLS register.
Signed-off-by: Nicolas Pitre
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If some hardware error occurs and the flush flag never updates,
we will hang forever in these routines. Add a timeout, and
print out a diagnostic if it is reached.
Signed-off-by: David S. Miller <davem@davemloft.net>
Some time ago, GAS was fixed to bring the .spillpsp directive in line
with the Intel assembler manual (there was some disagreement as to
whether or not there is a built-in 16-byte offset). Unfortunately,
there are two places in the kernel where this directive is used in
handwritten assembly files and those of course relied on the "buggy"
behavior. As a result, when using a "fixed" assembler, the kernel
picks up the UNaT bits from the wrong place (off by 16) and randomly
sets NaT bits on the scratch registers. This can be noticed easily by
looking at a coredump and finding various scratch registers with
unexpected NaT values. The patch below fixes this by using the
.spillsp directive instead, which works correctly no matter what
assembler is in use.
Signed-off-by: David Mosberger-Tang <davidm@hpl.hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Patch from Sascha Hauer
This patch adds the defines for the i.MX PWM controller
Signed-off-by: Steven Scholz
Signed-off-by: Sascha Hauer
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the locking for copy_user_page() and clear_user_page() into
the implementations which require locking. For simple memcpy/
memset based implementations, the locking is extra overhead which
is not necessary, and prevents preemption occuring.
Signed-off-by: Russell King <rmk@arm.linux.org.uk>
Add uart_insert_char(), which handles inserting characters into the
flip buffer. This helper function handles the correct semantics
for handling overrun in addition to inserting normal characters.
Signed-off-by: Russell King <rmk@arm.linux.org.uk>
Add pmd_off() and pmd_off_k() to obtain the pmd pointer for a
virtual address, and use them throughout the mm initialisation.
Signed-off-by: Russell King <rmk@arm.linux.org.uk>
I noticed this typo when trying to compile a kernel which had
CONFIG_HOTPLUG turned off. In that case, __devinit is no longer a
no-op and the compiler then detects a section-conflict. Fix by using
__devinitdata instead of __devinit.
Same patch also submitted by Darren Williams to fix compilation error
using sim_defconfig (which has CONFIG_HOTPLUG=n).
Signed-off-by: David Mosberger-Tang <davidm@hpl.hp.com>
Signed-off-by: Darren Williams <dsw@gelato.unsw.edu.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Updates to the wbsd driver.
* Fix to handle DAT3 card detection.
* Fixed bug which could cause large writes to stall in FIFO mode.
* Plug 'n Play support. In most cases you need ACPI PNP for this to work.
* Uses generic DMA API (ISA dependency removed).
This fixes some x86_64 bugs -
- maybe_map returns -1 on error instead of 0, which is interpreted as
physical address 0
- removed an include of ipc.h, which isn't needed
- fixed the calculation of signal frame location
- the signal delivery code is now immune to the stack expansion check
- added a missing include
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
tt-mode closes switch_pipes in exit_thread_tt and kills processes in
switch_to_tt, if the exit_state is EXIT_DEAD or EXIT_ZOMBIE.
In very rare cases the exiting process can be scheduled out after having set
exit_state and closed switch_pipes (from release_task it calls proc_pid_flush,
which might sleep). If this process is to be restarted, UML failes in
switch_to_tt with:
write of switch_pipe failed, err = 9
We fix this by closing switch_pipes not in exit_thread_tt, but later in
release_thread_tt. Additionally, we set switch_pipe[0] = 0 after closing.
switch_to_tt must not kill "from" process depending on its exit_state, but
must kill it after release_thread was processed only, so it examines
switch_pipe[0] for its decision.
Signed-off-by: Bodo Stroesser <bstroesser@fujitsu-siemens.com>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Only x86 and x86_64 use arch_align_stack(), all other subarches have:
#define arch_align_stack(x) (x)
So, if this definition is found, UML's own arch_align_stack() should be
skipped.
Signed-off-by: Bodo Stroesser <bstroesser@fujitsu-siemens.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
tt/mem.c still uses hardcoded TOP for i386 instead of CONFIG_TOP_ADDR provided
by subarch's Kconfig_XXXX, which would be right.
Signed-off-by: Bodo Stroesser <bstroesser@fujitsu-siemens.com>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
So, there I was, looking at my own code, wondering what the magic setjmp
return values did. This patch turns the constants that are used to make
requests of the initial thread into meaningful symbols.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This eliminates some stuff from arch/um/kernel/Makefile which refers to a
file which has long since been deleted.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Eliminate the non-inline version of switch_mm, which can't be used,
considering the inline version in asm/mmu_context.h
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
s390 tt-mode needs to save not only syscall number, but an further register
also.
Signed-off-by: Bodo Stroesser <bstroesser@fujitsu-siemens.com>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
s390 needs to change some parts of arch/um/kernel/ptrace.c. Thus, the code
regarding PEEKUSER and POKEUSER are shifted to arch/um/sys-<subarch>/ptrace.c.
Also s390 debug registers need to be updated, when singlestepping is switched
on / off. Thus, setting/resetting of singlestepping is centralized in the new
function set_singlestep(), which also inserts the macro
SUBARCH_SET_SINGLESTEP(mode), if defined.
Finally, s390 has the "ieee_instruction_pointer" in its
registers, which also is allowed to be read via
ptrace( PTRACE_PEEKUSER, getpid(), PT_IEEE_IP, 0);
To implement this feature, sys_ptrace inserts the macro
SUBARCH_PTRACE_SPECIAL, if defined.
Signed-off-by: Bodo Stroesser <bstroesser@fujitsu-siemens.com>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Command line handling cleanups - a couple of things made static and an
unused declaration removed from header.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I accidentally included include/asm-um/elf.h as a real file in a previous
patch. This patch eliminates it.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the __deprecated from verify_area_skas and verify_area_tt. Since
verify_area is itself marked __deprecated, and it is the only caller of
these, then they don't need to be marked. Marking them only makes the
build noisier.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds a VIDIOC_G_FREQUENCY command to tuner-core.c and sets
lowest and highest tunable frequencies in v4l2_tuner structure returned by
VIDIOC_G_TUNER command.
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Cc: Gerd Knorr <kraxel@bytesex.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In VIDIOC_S_FREQUENCY command in tuner-core.c, t->freq is set to a new
value before calling set_freq(). This is not necessary, as set_freq() sets
t->freq itself. Moreover, it causes problems with Philips tuners, as they
need to take into consideration difference between previous and new
frequency.
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Cc: Gerd Knorr <kraxel@bytesex.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In separating out support for hardware floating point we missed the fact
that both POWER3 and POWER4 have HW FP. Enable CONFIG_PPC_FPU for POWER3
and POWER4 fixes the issue.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch enables CONFIG_RTAS_PROC by default on pSeries. This will
preserve /proc/ppc64/rtas/rmo_buffer, which is needed by librtas.
Signed-off-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This change from March 3rd causes the partition parsing code to ignore
partitions which have a signature byte of zero. Turns out that more people
have such partitions than we expected, and their device numbering is coming up
wrong in post-2.6.11 kernels.
So revert the change while we think about the problem a bit more.
Cc: Andries Brouwer <Andries.Brouwer@cwi.nl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I somehow missed that there is external usage of rd_size on some
architectures.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Malli Chilakala