The userspace must not be able to issue ethtool command and manage the
mii before it is completely initialized. Avoid some pesky "eth%d" messages.
Signed-off-by: Arnaud Patard <apatard@mandriva.com>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
From: Gertjan van Wingerde <gwingerde@home.nl>
Attached patch updates the definitions of the generic ieee80211 stack to
the latest versions of the published 802.11x specification suite.
Signed-off-by: Gertjan van Wingerde <gwingerde@home.nl>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
This removes one trap for a programmer, few unused macros, and one
unused struct.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
From: Imre Deak <imre.deak@nokia.com>
I had a problem where doing an open after a close left the device
unusable. netif_carrier_on should be called whenever we go to the
associated state, but this is not so in case of a close->open sequence.
Signed-off-by: Jiri Benc <jbenc@suse.cz>
From: Adrian Bunk <bunk@stusta.de>
This patch contains the following possible cleanups:
- make needlessly global code static
- remove the unused IPW_DEBUG_ENABLED
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
From: Pavel Machek <pavel@ucw.cz>
ipw2100 uses custom debug prints that are sometimes longer and always
harder to read than normal printk. They also introduced some bugs where
prefix is printed twice.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
From: Pavel Machek <pavel@ucw.cz>
ipw2100 uses strange X__ prefixes even for symbols already prefixed
by ipw2100. Fixed.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
The tg3_abort_hw() call in tg3_test_loopback() is causing lockups on
some devices. tg3_abort_hw() disables the memory arbiter, causing
tg3_reset_hw() to hang when it tries to write the pre-reset signature.
tg3_abort_hw() should only be called after the pre-reset signature has
been written. This is all done in tg3_reset_hw() so the tg3_abort_hw()
call is unnecessary and can be removed.
[ Also bump driver version and release date. -DaveM ]
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver version, white space, comments & other
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add cpu cycle saver microcode to 8086:{1209/1229} other than ICH devices.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fixed endian bug associated with cb_i bit in xmit_prepare
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
added msleep_interruptible delay right before returning from diag_test
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Do not check Rx packet length against mtu - patch from Darren Tucker
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
airo_cs is broken on m32r; marked as such. [Proper fix would involve
separating PCI-dependent parts and making sure they don't get in the
way _and_ arranging for asm/scatterlist.h getting picked on m32r]
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ISA parts of tms380tr are using ISA DMA helpers and should depend on
ISA_DMA_API.
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The purpose of this patch:
- Adopt the DMA API (jazzsonic, macsonic & core driver).
- Adopt the driver model (macsonic).
This part was cribbed from jazzsonic. As a consequence, macsonic once
again works as a module. Driver model is also used by the DMA calls.
- Support 16 bit cards (macsonic & core driver, also affects jazzsonic)
This code was adapted from the mac68k linux 2.2 kernel, where it has
languished for a long time.
- Support more 32-bit mac cards (macsonic)
Also from mac68k repo.
- Zero-copy buffer handling (core driver)
Provides a nice performance improvement. The new algorithm incidentally
helped to replace the old Jazz DMA code.
The patch was tested on a variety of macs (several 32-bit quadra built-in
NICs, a 16-bit LC PDS NIC and a 16-bit comm-slot NIC), and also on MIPS
Jazz.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Acked-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
[PATCH] [NET] mv643xx: add workaround for HW checksum generation bug
The hardware checksum generator on the mv64xxx occasionally generates
an incorrect checksum. This patch works around the issue and enables
hardware checksum generation.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
Patch Description:
This patch incorporates the following hardware fixes required
for Xframe II adapter.
1. New values to program the dtx_control register.
2. Disable memory controller interrupts(MC_INTR) since these
are now monitored thru' a poll routine.
3. Don't reset an XframeII card on an ECC double-bit error(It
can recover).
4. Save/restore PCI config space before/after a reset irrespective
of Xframe I or II card.
5. Bumped up the driver version no. to 2.0.3.1
Please review the patch and apply the same if it looks ok.
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Now that all tms380 devices have a valid
struct device with dma_mask, remove dmalimit from tmsdev_init().
Kconfig: depend tms380tr and madgemc on MCA.
abyss.c, proteon.c, skisa.c, tmspci.c, tms380tr.h:
remove dmalimit parameter from tmsdev_init().
tms380tr.c: use device->dma_mask instead of dmalimit.
madgemc.c: move to new MCA API using struct device.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
A problem was reported by Grant Grundler on an HP rx8620 using IOX
Core LAN partno(A7109-6) 5701 copper NIC. The tg3 driver mistakenly
detects this NIC as having a SerDes PHY and link does not come up as a
result.
The problem was caused by an incorrectly programmed eeprom that set the
NIC_SRAM_DATA_CFG_PHY_TYPE_FIBER bit in the NIC_SRAM_DATA_CFG location.
This patch will override the NIC_SRAM_DATA_CFG_PHY_TYPE_FIBER bit if a
valid PHY ID is read from the MII registers on older 570x chips where
the MII interface is not used on SerDes chips. On newer chips such as
the 5780 that use MII for both copper and SerDes, SerDes detection must
rely on the eeprom.
This patch will make the SerDes detection identical to versions 3.25 and
older.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Grant Grundler <iod00d@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/e1000/e1000_main.c: In function `e1000_clean_tx_irq':
drivers/net/e1000/e1000_main.c:2774: warning: size_t format, dma_addr_t arg (arg 8)
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The multicast code of the fmvj18x_cs driver is broken.
I fixed it to work properly.
Signed-off-by: komurojun-mbn@nifty.com
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
SIS190 must select MII since it's using it.
While I was editing the Kconfig entry, I also converted the spaces to
tabs.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The Linksys EG1032 uses Realtek's 8169 chipset.
Credit goes to Bob Wilson <bwilson4web@hotmail.com> for the report.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Use msleep_interruptible() instead of delay_cycx() to guarantee the task
delays as expected. Remove the prototype and definition of delay_cycx().
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Rüdiger found a bug in nv_open that explains some of the reports
with duplex mismatches:
nv_open calls nv_update_link_speed for initializing the hardware link speed
registers. If current link setting matches the values in np->linkspeed and
np->duplex, then the function does nothing.
Usually, doing nothing is the right thing, but not in nv_open: During
nv_open, the registers must be initialized because the nic was reset.
The attached patch fixes that by setting np->linkspeed to an invalid value
before calling nv_update_link_speed from nv_open.
Signed-Off-By: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The DM9000 driver is responding to ioctl() calls it should not be. This
can cause problems with the wireless tools incorrectly indentifying the
device as wireless capable, and crashing under certain operations.
This patch also moves the version printk() to the init call, so that
you only get it once for multiple devices, and to show it is loaded
if there are no defined dm9000s
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fix DM9000 driver usage of spinlocks, which mainly came to light
when running a kernel with spinlock debugging. These come down to:
1) Un-initialised spin lock
2) Several cases of using spin_xxx(lock) and not spin_xxx(&lock)
3) move the locking around the phy reg for read/write to only
keep the lock when actually reading or writing to the phy.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
After suspend the driver needs to retest link status in case the cable
has been inserted or removed during the suspend.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
- Using the right register clearly improves chances of getting the MII
code and thus the driver working at all.
- On startup check the media type before setting up duplex or we might
spend the first 1.2s with a wrong duplex setting.
- Get rid of whitespace lines.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The flush threshold in the MAC chip should be increased.
Found while reviewing vendor version of sk98lin driver.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Some versions of the Marvell yukon generate bogus sensor warning interrupts.
The driver would flood log with these messages. Handle this situation
cleanly by masking away at boot time.
Fixes: http://bugs.gentoo.org/show_bug.cgi?id=87182
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
drivers/net/skge.c | 24 ++++++++++--------------
drivers/net/skge.h | 8 ++++++--
2 files changed, 16 insertions(+), 16 deletions(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Replace remaining WLAN_FC_* defines with the ones used in ieee80211
header file. This completes the move from hostap version of frame
control field processing to ieee80211 version.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Remove backwards compatibility define for WLAN_CAPABILITY_ESS now that
net/ieee80211.h defines this.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Al Viro