Since i2c autoprobing is no longer supported by v4l2 we need to make sure
that the i2c modules are linked before the v4l2 modules. The v4l2 modules
now rely on the presence of the i2c modules, so these must have initialized
themselves before the v4l2 modules.
The exception is the ir-kbd-i2c module, which is the only one still using
autoprobing. This one should be loaded at the end of the v4l2 module. Loading
it earlier actually causes problems with tveeprom. Once ir-kbd-i2c is no
longer autoprobing, then it has to move up as well.
This is only an issue when everything is compiled into the kernel.
Thanks to Marcus Swoboda for reporting this and Udo Steinberg for testing
this patch.
Tested-by: Udo A. Steinberg <udo@hypervisor.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix a regression caused by changeset 9133:64aed7485a43 - v4l: disconnect
kernel number from minor
Before the above changeset, ov511_probe used to allow forcing to use a
certain specific set of video devices, like:
modprobe ov511 unit_video=4,1,3 num_uv=3
So, assuming that you have 5 ov511 devices, and connect they one by one,
they'll gain the following device numbers (at the connection order):
/dev/video4
/dev/video1
/dev/video3
/dev/video0
/dev/video2
However, this was changed due to this change at video_register_device():
+ nr = find_next_zero_bit(video_nums[type], minor_cnt, nr == -1 ? 0 : nr);
With the previous behavior, a trial to register on an already allocated mirror
would fail, and a loop would get the next requested minor. However, the current
behavior is to get the next available minor instead of failing. Due to that,
this means that the above modprobe parameter will give, instead:
/dev/video5
/dev/video6
/dev/video7
/dev/video8
/dev/video9
In order to restore the original behavior, a static var were added,
storing the amount of already registered devices.
While there, it also fixes the locking of the probe/disconnect functions.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A bunch of V4L drivers generate BTN_0 instead of KEY_CAMERA key presses.
X11 is able to handle KEY_CAMERA automatically these days while BTN_0 is
not treated at all. Thus it would be of big benefit if the camera drivers
would consistently generate KEY_CAMERA. Some drivers (uvc) already do,
this patch updates the remaining drivers to do the same.
I only possess a limited set of webcams, so this isn't tested with all
cameras. The patch is rather trivial and compile tested, so I'd say it's
still good enough to get merged.
Signed-off-by: Lennart Poettering <mzxreary@0pointer.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
vfree() does it's own NULL checking,so no need for check before
calling it.
Signed-off-by: Figo.zhang <figo1802@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
it is better return -ENOMEM than -EIO
Signed-off-by: Figo.zhang <figo1802@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This adds support for DVB-T on the Leadtek DVR3100 H and should also get analog
TV capture from the tuner working properly as well.
DVB-T 6 MHz and 8 MHz have been tested and verified to work by Terry Wu of
Leadtek. DVB-T 7 MHz has also been verified working with a change developed by
Terry to the tuner-xc2028.c driver.
Special thanks go to Terry Wu <terrywu2009@gmail.com> of Leadtek who provided
the needed information and testing to get digital TV working for the Leadtek
DVR3100 H.
Reported-by: Terry Wu <terrywu2009@gmail.com>
Tested-by: Terry Wu <terrywu2009@gmail.com>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Herton Ronaldo Krzesinski from Mandriva reported that one Bison Electronics
webcam exposes a non-UVC interface descriptor. Instead of failing completely,
ignore trailing non-UVC descriptors and move on.
Thanks to Herton for reporting the problem and submitting a patch proposal.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Aveo Technology USB 2.0 Camera (1871:0306) requires the
PROBE_EXTRAFIELDS quirk. Add a corresponding entry in the device IDs list.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Setting a new frame format or size will likely change the buffer size required
to store a complete video frame. To avoid a buffer overflow, don't allow
VIDIOC_S_FMT calls when video buffers are already allocated.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Another device (5986:0241) has been reported to advertise a UVC control it
does not support. Rework the control blacklist to match devices by their
VID:PID instead of trying to be clever about which controls might not be
supported properly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The quirk list has grown and was in need of sorting. This is now done. Add a new vflip quirk for the ASUS A7V while we're at it. Thanks to Carsten Menzel for reporting.
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add vflip quirk for the ASUS A6VA. Thanks to Salvo Di Rosa for reporting.
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Lenovo Y300 has its sensor upside down. Quirk it to gain normal functionality.
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This replaces dma_sync_single() with dma_sync_single_for_cpu() because
dma_sync_single() is an obsolete API; include/linux/dma-mapping.h says:
/* Backwards compat, remove in 2.7.x */
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix v4l2-device usage of i2c_unregister_device() and handle the case of
CONFIG_I2C=m & CONFIG_MEDIA_VIDEO=y.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add an au0828 module option that allows a user to override the USB speed check.
Intended for advanced users who understand the consequences of trying to use
the device with a 12Mbps bus.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add an em28xx module option that allows a user to override the USB speed check.
Intended for advanced users who understand the consequences of trying to use
the device with a 12Mbps bus.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch removes some remaining dead code. Warning showed up in Hans
Verkuil's daily report after I committed hg changeset 7f2eea75118b.
Thanks to Michael Krufky for bringing the warning to my attention.
Cc: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make the KWorld 2800d work properly. In this case, that means making the
profile more generic so that it works for both the Pointnix Intra-Oral USB
camera and the KWorld device.
The device provides the audio through a pass-thru cable, so we don't need
an actual audio capture profile (neither the K-World device nor the Pointnix
have an onboard audio decoder).
Thanks to Paul Thomas for providing sample hardware.
Cc: Paul Thomas <pthomas8589@gmail.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The au0828 basically just doesn't work at 12 Mbps. The isoc pipe needs
nearly 200 Mbps for analog support, so users would see garbage video, and on
the DVB/ATSC side scanning is likely to work but if the user tried to tune it
would certainly appear to have failed.
It's better to fail explicity up front and tell the user to plug into a USB 2.0
port, than to let the driver load and the user have weird problems with tuning
and garbage video.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The em28xx basically just doesn't work at 12 Mbps. The isoc pipe needs
nearly 200 Mbps for analog support, so users would see garbage video, and on
the DVB/ATSC side scanning is likely to work but if the user tried to tune it
would certainly appear to have failed.
It's better to fail explicity up front and tell the user to plug into a USB 2.0
port, than to let the driver load and the user have weird problems with tuning
and garbage video.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks to David Ward and Mike Krufky for reporting the problem and
debugging this as an unresolved symbol due to a 64 bit divide on a 32 bit
system. David Ward provided the content of this patch; Andy Walls only
performed some cosmetic edits.
Reported-by: David Ward <david.ward@gatech.edu>
Signed-off-by: David Ward <david.ward@gatech.edu>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Test Code: (Provided by Douglas)
v4l-dvb/v4l2-apps/test/stress-buffer.c
The audio DMA area was never being freed and would slowly leak over
time as the v4l device was opened and closed by an application.
Thanks again to Douglas for generating the test code to help locate
memory leaks!!!
Signed-off-by: Robert Krakora <rob.krakora@messagenetsystems.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove always false if over unsigned int variable
Signed-off-by: Filipe Rosset <rosset.filipe@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch add cx23885 support for card "Mygica X8506 DMB-TH".
It should work on "Magic-Pro ProHDTV Extreme" as well, as they are
same hardware with different branding.
Sign-off-by: David T.L. Wong <davidtlwong@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Enables analog/digital tv, radio and remote control (gpio).
Tested-by: Marcin Wojcikowski <emtees.mts@gmail.com>
Tested-by: Karel Juhanak <karel.juhanak@warnet.cz>
Tested-by: Andrew Goff <goffa72@gmail.com>
Tested-by: Jan Novak <novak-j@seznam.cz>
Signed-off-by: Miroslav Sustek <sustmidown@centrum.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- Extend the gain range
- Adjust the exposure
- Remove the broken autogain
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The YUYV 640x480 format did not work with ov965x.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix the burst gate delays to use a crystal value of 28636360 as assumed by
the rest of the driver. Also have the initial color sub-carrier freq paramter
use the src decimation ratio per the documentation, instead of the actual
crystal/pixel clock ratio. The tracking circuit will find the correct color
subcarrier in any case, as long as we're close. Also fix up some debug print
statements.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Finish changes for sliced and raw VBI for 625 line systems. Tested with VPS
and WSS being emitted by a PVR-350 in field 1 lines 16 and 23.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Initial changes to get sliced VBI for 625 line system working. This is patch
is untested.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The i2c quirk in the saa7134_i2c_xfer function does a bogus write
to i2c address 0xfd, to work around a bug in the silicon that
affects read transactions.
Unfortunately, this hack is not working properly, since the bogus
write is to 0xfd, an invalid i2c address. Fix this quirk by using
an actual valid i2c address, 0xfe, which is still unlikely to be
used as an i2c address for any actual i2c client.
This is required in order to properly communicate with a TDA10048
DVB-T demod located at i2c address 0x10 on the primary i2c bus.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Steve missed the HVR1210 config struct for the TDA10048 in his IF freq patch.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
pvrusb2: Ensure we specify I/F's for all bandwidths
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Acked-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx23885: Ensure we specify I/F's for all bandwidths
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The variable minor have assigned value twice, the first time is in the
initial "video_device" data struct in those drivers, pls see
saa7134-video.c,line 2503.
---
Signed-off-by: Figo.zhang <figo.zhang@kolorific.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil