commit 04d06ad0f1 have added menuconfig support
for the whole USB Kconfig, but there are still menuconfig need for usb/serial,
usb/atm, and usb/gadget, so that the user can disable all the options in that
menu at once instead of having to disable each option separately.
Signed-off-by: Denis Cheng <crquan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Various small at91_udc cleanups:
- Use generic GPIO calls, not older platform-specific ones
- Use gpio_request()/gpio_free()
- Use VERBOSE_DEBUG convention, not older VERBOSE
- Fix sparse complaint about parameter type (changed to gfp_t)
- Add missing newline to some rarely-seen debug messages
- Fix some old cleanup bugs on probe() fault paths
Also add a mechanism whereby rm9200 gpios can drive the D+ pullup
through an inverting transistor, based on a patch from Steve Birtles.
Most UDC drivers supporting a GPIO based pullup should probably have
such an option, but testing it requries such a board in hand!
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Steve Birtles <arm_kernel_development@micromark.net.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix a small glitch noted by Yannick Cote. There is no endpoint number
six, so if a (broken) host wrongly tried to change or read status of
that endpoint, the driver could access reserved register space.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Yannick Cote <yanick@yanos.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix potential (never-observed) oops on rare error path,
bugzilla #9594. Fix uses the same test as used earlier.
Also make the adjacent "else" block look like an "else" block
instead of hiding like a bug.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some boards (like e.g. Tosa) invert the VBUS-detection signal:
it's low when a host is supplying VBUS, and high otherwise.
Allow specifying whether gpio_vbus value is inverted.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1025) changes the default power budget for dummy-hcd to
500 mA and makes it a preprocessor parameter for easier testing.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1017) makes dummy_hcd behave more like the other USB
peripheral controller drivers by no longer registering its
gadget driver on the platform bus. Doing that has always been a
mistake, since a usb_gadget_driver isn't a platform_driver. Instead
the gadget driver is left unregistered in sysfs.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I'm having problem with oopses when rebooting, if I modprobe g_serial
and rmmod g_serial and do a reboot I get an oops in device_shutdown().
The reason seems to be that usb_gadget_unregister_driver() doesn't do
enough cleanup. With this at91_udc patch I don't get the oops.
Signed-off-by: Patrik Sevallius <patrik.sevallius@enea.com>
[ Same bug was in other peripheral controller drivers; fixed ]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We now have pr_err(), pr_warning(), and friends ... start using
them in the gadget stack instead of printk(KERN_ERR) and friends.
This gives us shorter lines and somewhat increased readability.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
G_PRINTER: Adds a USB printer gadget driver for use in printer firmware.
This adds a USB printer gadget driver for use in printer firmware.
The printer gadget channels data between the USB host and a userspace
program driving the print engine. The user space program reads and
writes the device file /dev/g_printer to receive or send printer data.
It can use ioctl calls to the device file to get or set printer status.
Signed-off-by: Craig W. Nadler <craig@nadler.us>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for SuperH SH7722 USB Function.
M66592 is similar to SH7722 USBF. It can support SH7722 USBF by
changing several M66592 code.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The current omap udc dosen't support the DMA mode and it has some problem
at setup time on OMAP2 with previous patch file. I found that the code
assumes bulk out required the big data transfer. But MODE SELECT(6) sent
the only 24 bytes. it makes a problem. So I implement the small packets
handling for it.
It is tested with both linux and windows.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- 'irq' argument is merely used in place of a constant; replace its usage
with that constant.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For fsl_usb2_udc driver, ep0 also has a descriptor. Current code is
misleading and contains a logical mistake. Here is the patch to fix it.
http://bugzilla.kernel.org/show_bug.cgi?id=9595
Cc: stable <stable@kernel.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This header file exists only for some hacks to adapt alsa-driver
tree. It's useless for building in the kernel. Let's move a few
lines in it to sound/core.h and remove it.
With this patch, sound/driver.h isn't removed but has just a single
compile warning to include it. This should be really killed in
future.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Add support for Atmel's AT91CAP9 Customizable Microcontroller family.
<http://www.atmel.com/products/AT91CAP/Default.asp>
Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Correct hanging while disconnecting the USB device cable. Prevent a race
between vbus and UDP interrupts. This bug was tracked on at91sam9260ek
boards.
A usb resume interrupt was firing after the vbus interrupt : the IP was
then already stoped and not able to deal with it (no more clock). A simple
interrupt disabling is ok as the "end of bus reset" irq is non maskable and
ok to resume the USB device IP.
Signed-off-by: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some CPUs in the S3C24XX series do not support readback of the
value of a pin when the pin has been configured to an IRQ.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If another driver wants to claim the vbus pin, say
to notify the user of an connect/disconnect then allow
the IRQ to be shared by specifiying IRQ_SHARED in the
flags.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixup the fallout from the arch moves earlier in the kernel
series.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
This fixes some build errors ... unclear how this got past earlier tests.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Get rid of pointless pci_set_mwi() compiler warning.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* Convert files to UTF-8.
* Also correct some people's names
(one example is Eißfeldt, which was found in a source file.
Given that the author used an ß at all in a source file
indicates that the real name has in fact a 'ß' and not an 'ss',
which is commonly used as a substitute for 'ß' when limited to
7bit.)
* Correct town names (Goettingen -> Göttingen)
* Update Eberhard Mönkeberg's address (http://lkml.org/lkml/2007/1/8/313)
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
The task_struct->pid member is going to be deprecated, so start
using the helpers (task_pid_nr/task_pid_vnr/task_pid_nr_ns) in
the kernel.
The first thing to start with is the pid, printed to dmesg - in
this case we may safely use task_pid_nr(). Besides, printks produce
more (much more) than a half of all the explicit pid usage.
[akpm@linux-foundation.org: git-drm went and changed lots of stuff]
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Keep track of the device status (as returned by the GET_STATUS
request) and allow it to be manipulated by set_selfpowered() as
well as SET_FEATURE/CLEAR_FEATURE (for remote wakeup)
Implement the wakeup() op, which refuses to do anything if the
DEVICE_REMOTE_WAKEUP feature wasn't set by the host. Now this
driver passes USBCV (at least, with gadget zero).
Fix one more locking bug; lockdep is every developer's friend.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a driver for the Atmel USBA UDC which can be found integrated
on AT32AP700x AVR32 processors. For hardware documentation, please see
the AT32AP7000 data sheet:
http://www.atmel.com/dyn/resources/prod_documents/doc32003.pdf
This is a dual speed controller (connects at high or full speed).
The driver supports up to 7 control, bulk, interrupt and isochronous
endpoints with some constraints. Bulk, interrupt and isochronous
transfers are driven by DMA.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move <linux/usb_gadget.h> to <linux/usb/gadget.h>, reducing
some of the clutter in the main include directory.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After Serial gadget is being unloaded, neither serial itself, nor other
gadget stuff can be loaded subsequently.
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix a longstanding race in the Ethernet gadget driver, which can cause an
oops on device disconnect. The fix is just to make the TX path check
whether its freelist is empty. That check is otherwise not necessary,
since the queue is always stopped when that list empties (and restarted
when request completion puts an entry back on that freelist).
The race window starts when the network code decides to transmit a packet,
and ends when hard_start_xmit() grabs the freelist lock. When disconnect()
is called inside that window, it shuts down the TX queue and breaks the
otherwise-solid assumption that packets are never sent through a TX queue
that's stopped.
Signed-off-by: Benedikt Spranger <bene@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as984) fixes a rather elementary mistake in dummy_hcd.
The new statement label should come before the spin_unlock_irqrestore,
not after it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as979) removes the last vestiges of urb->status from the
host controller drivers and the root-hub emulator. Now the field
doesn't get set until just before the URB's completion routine is
called.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
CC: Olav Kongas <ok@artecdesign.ee>
CC: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
CC: Tony Olech <tony.olech@elandigitalsystems.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as973) reorganizes the way dummy-hcd sets urb->status. It
now keeps the information in a local variable until the last moment.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as983) makes a test for minimum-length command sizes in
g_file_storage less restrictive. It doesn't matter because commands
with bad lengths will be detected later on anyway, and doing it like
this makes the driver interoperable with certain buggy hosts such as
the JVC HiFi (reported by Samuel Hangouet).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as970) adds a new urb->unlinked field, which is used to
store the status of unlinked URBs since we can't use urb->status for
that purpose any more. To help simplify the HCDs, usbcore will check
urb->unlinked before calling the completion handler; if the value is
set it will automatically override the status reported by the HCD.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
CC: Olav Kongas <ok@artecdesign.ee>
CC: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
CC: Tony Olech <tony.olech@elandigitalsystems.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as969) continues the ongoing changes to the way HCDs
report URB statuses. The programming interface has been simplified by
making usbcore responsible for clearing urb->hcpriv and for setting
-EREMOTEIO status when an URB with the URB_SHORT_NOT_OK flag ends up
as a short transfer.
By moving the work out of the HCDs, this removes a fair amount of
repeated code.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
CC: Olav Kongas <ok@artecdesign.ee>
CC: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
CC: Tony Olech <tony.olech@elandigitalsystems.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as957) makes some minor cleanups to the g_file_storage
driver:
Update the copyright date and version string;
Uniformize the logging macros for the gadget and the LUNs;
Remove "inline" markers -- nowadays we rely on the compiler
to decide which routines are best inlined;
Use the print_hex_dump() library routines;
Remove some unnecessary assignments within conditionals
and fix some close-brace indenting levels;
Fix some column-80 violations.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as954) implements a suggestion of David Brownell's. Now
the host controller drivers are responsible for linking and unlinking
URBs to/from their endpoint queues. This eliminates the possiblity of
strange situations where usbcore thinks an URB is linked but the HCD
thinks it isn't. It also means HCDs no longer have to check for URBs
being dequeued before they were fully enqueued.
In addition to the core changes, this requires changing every host
controller driver and the root-hub URB handler. For the most part the
required changes are fairly small; drivers have to call
usb_hcd_link_urb_to_ep() in their urb_enqueue method,
usb_hcd_check_unlink_urb() in their urb_dequeue method, and
usb_hcd_unlink_urb_from_ep() before giving URBs back. A few HCDs make
matters more complicated by the way they split up the flow of control.
In addition some method interfaces get changed. The endpoint argument
for urb_enqueue is now redundant so it is removed. The unlink status
is required by usb_hcd_check_unlink_urb(), so it has been added to
urb_dequeue.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
CC: Olav Kongas <ok@artecdesign.ee>
CC: Tony Olech <tony.olech@elandigitalsystems.com>
CC: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Clean up gadget zero, using newer APIs and conventions:
- gadget_is_dualspeed() and gadget_is_otg() ... #ifdef removal
- Remove many now-needless #includes
- Use the VERBOSE_DEBUG convention
- Some whitespace fixes.
- A few comment updates
- Plus a few other small cleanups: don't pass gfp_t around when it's
always going to be GFP_ATOMIC, and do static init of serial number.
Also go to straight GPL; there's no real point in dual licensing this
stuff any more.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Clean up the file storage gadget, using newer APIs and conventions:
- gadget_is_dualspeed() and gadget_is_otg() ... #ifdef removal
- Remove many now-needless #includes
- Use the DEBUG (from Kconfig+Makefile) and VERBOSE_DEBUG conventions.
- Remove some "sparse" warnings (it still dislikes the __user annotations)
This gave only a minor object code shrinkage.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Clean up the serial gadget, using newer APIs and conventions:
- gadget_is_dualspeed() and gadget_is_otg() ... #ifdef removal
- Remove many now-needless #includes
- Use the DEBUG and VERBOSE_DEBUG conventions; turned up a bug in
the original debug messaging
- Various whitespace fixes.
This gave only a minor object code shrinkage, but the source looks
much cleaner in various places.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Al Borchers <alborchers@steinerpoint.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Clean up the midi gadget, using newer APIs and conventions:
- Remove many now-needless #includes
- Use the DEBUG (from Kconfig+Makefile) and VERBOSE_DEBUG conventions.
- Whitespace fixes
There should be no effect on object code size.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Ben Williamson <ben.williamson@greyinnovation.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Clean up the ethernet gadget, using newer APIs and conventions:
- gadget_is_dualspeed() and gadget_is_otg() ... #ifdef removal
- Remove many now-needless #includes
- Use the VERBOSE_DEBUG convention
- Minor whitespace fixes.
- Fix a warning from "sparse".
Surprisingly, this saved about 2K of code (16%) on a fullspeed-only
ARMv4 platform. I'm bit puzzled by that (it's so much!), but approve
of the result.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds two small inlines to the gadget stack, which will
often evaluate to compile-time constants. That can help
shrink object code and remove #ifdeffery.
- gadget_is_dualspeed(), currently always a compile-time
constant (depending on which controller is selected).
- gadget_is_otg(), usually a compile time "false", but this
is a runtime test if the platform enables OTG (since it's
reasonable to populate boards with different USB sockets).
It also updates two peripheral controller drivers to use these:
- fsl_usb2_udc, mostly OTG-related bugfixes: non-OTG devices
must follow the rules about drawing VBUS power, and OTG ones
need to reject invalid SET_FEATURE requests.
- omap_udc, just scrubbing a bit of #ifdeffery.
And also gadgetfs, which lost some #ifdefs and moved to a more
standard handling of DEBUG and VERBOSE_DEBUG.
The main benefits come from patches which will follow.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Denis Cheng