commit 7cd5b08be3 added a second regression:
some Dell's and Compaq's lockup on boot. So we revert most of the code.
The ICH9 reboot issue remains in place and will need some more fixing... :-(
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The code used '&= 0x00002000' when it tried to set the TCO_EN bit, which
obviously didn't set that bit at all, but instead just reset all the
other bits in the SMI_EN register.
This bug seemingly caused various random behavior, with Frans Pop
reporting that X.org just silently hung at startup and Rafael Wysocki
reports the fan spinning with full speed.
See
http://lkml.org/lkml/2008/12/3/178http://bugzilla.kernel.org/show_bug.cgi?id=12162
The problem seems to have been triggered by "[WATCHDOG] iTCO_wdt :
problem with rebooting on new ICH9 based motherboards" (commit
7cd5b08be3), but the bogus code existed
before that too (in the "supermicro_old_pre_stop()" function), it just
apparently never showed up due to different logic.
In that commit the broken code got moved around and now gets executed
much more.
Reported-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Frans Pop <elendil@planet.nl>
Cc: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the following I/O controller hubs:
ICH7DH, ICH9M, ICH9M-E, ICH10, ICH10R, ICH10D and ICH10DO.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The iTCO_wdt code was not clearing the correct bits.
It now clears the timeout status bit and then the
SECOND_TO_STS bit and then the BOOT_STS bit.
Note: we should first clear the SECOND_TO_STS bit
before clearing the BOOT_STS bit.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
: On Intel motherboards with the ICH9 based I/O controllers
(Like DP35DP and DG33FB) the iTCO timer counts but it doesn't reboot the
system after the counter expires.
This patch fixes this by moving the enabling & disabling of the TCO_EN bit
in the SMI_EN register into the start and stop code.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This brings the watchdog drivers into line with coding style.
This patch takes cares of the indentation as described in chapter 1.
Main changes:
* Re-structure the ioctl switch call for all drivers as follows:
switch (cmd) {
case WDIOC_GETSUPPORT:
case WDIOC_GETSTATUS:
case WDIOC_GETBOOTSTATUS:
case WDIOC_GETTEMP:
case WDIOC_SETOPTIONS:
case WDIOC_KEEPALIVE:
case WDIOC_SETTIMEOUT:
case WDIOC_GETTIMEOUT:
case WDIOC_GETTIMELEFT:
default:
}
This to make the migration from the drivers to the uniform watchdog
device driver easier in the future.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add the Intel ICH9DO controller ID's for the iTCO_wdt kernel driver and bump
the driver version.
Tested on an P5E-VM DO ASUS motherboard.
Signed-off-by: Gabriel Craciunescu <nix.or.die@googlemail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Add all LPC bridges for the 631xESB/632xESB I/O chipset.
The datasheet says:
* Device Function = B0:D31:FO
* Function Description = LPC interface
* DEV ID = 267xh
* Comment = 2670h-267Fh
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add 631xESB/632xESB support to the iTCO_wdt driver.
Signed-off-by: Sergey Kononenko <sergk@sergk.org.ua>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The ACPI/PM base I/O address which is the base
for the TCO registers is defined as bits [15:7]
(highest bit is 31, lowest is 0)
The code however only reads bits [14:7]. So
base_address &= 0x00007f80;
needs to be:
base_address &= 0x0000ff80;
This patch fixes this.
Signed-off-by: Ate Wijma <ajwijma@hotmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Many struct file_operations in the kernel can be "const". Marking them const
moves these to the .rodata section, which avoids false sharing with potential
dirty data. In addition it'll catch accidental writes at compile time to
these shared resources.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
change default=CONFIG_WATCHDOG_NOWAYOUT in the module parameter
for nowayout by it's real value (0 or 1) by using:
__MODULE_STRING(WATCHDOG_NOWAYOUT)
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add vendor specific support to the intel TCO timer based watchdog
devices. At this moment we only have additional support for some
SuperMicro Inc. motherboards.
Signed-off-by: Robert Seretny <lkpatches@paypc.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
gcc emits the following warning:
drivers/char/watchdog/iTCO_wdt.c: In function ‘iTCO_wdt_ioctl’:
drivers/char/watchdog/iTCO_wdt.c:429: warning: ‘time_left’ may be used uninitialized in this function
This indicates a condition near enough to a bug, to want to fix.
iTCO_wdt_get_timeleft() stores a value in 'time_left' iff
iTCO_version==(1 or 2). This driver only supports versions
1 or 2, so this is ok. However, since (a) the return value of
iTCO_wdt_get_timeleft() is handled anyway, (b) it fixes the warning,
and (c) it future-proofs the driver, we go ahead and add the obvious
return value.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Return ENOTTY instead of ENOIOCTLCMD in user-visible ioctl() results
The watchdog drivers used to return ENOIOCTLCMD for bad ioctl() commands.
ENOIOCTLCMD should not be visible by the user, so use ENOTTY instead.
Signed-off-by: Samuel Tardieu <sam@rfc1149.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Since we are using the device driver model,
we don't need to arrange the shutdown via a
reboot_notifier.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
for_each_pci_dev calls pci_get_device (and thus
it calls pci_dev_get). So we need to do a pci_dev_put
to keep the refcounting correct.
(Thanks to Jiri Slaby <jirislaby@gmail.com>)
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Hardware driver for the intel TCO timer based watchdog devices.
These drivers are included in the Intel 82801 I/O Controller
Hub family (from ICH0 up to ICH7) and in the Intel 6300ESB
controller hub.
This driver will replace the i8xx_tco.c driver.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>