Quite a long time back, prepare_hugepage_range() replaced
is_aligned_hugepage_range() as the callback from mm/mmap.c to arch code to
verify if an address range is suitable for a hugepage mapping.
is_aligned_hugepage_range() stuck around, but only to implement
prepare_hugepage_range() on archs which didn't implement their own.
Most archs (everything except ia64 and powerpc) used the same
implementation of is_aligned_hugepage_range(). On powerpc, which
implements its own prepare_hugepage_range(), the custom version was never
used.
In addition, "is_aligned_hugepage_range()" was a bad name, because it
suggests it returns true iff the given range is a good hugepage range,
whereas in fact it returns 0-or-error (so the sense is reversed).
This patch cleans up by abolishing is_aligned_hugepage_range(). Instead
prepare_hugepage_range() is defined directly. Most archs use the default
version, which simply checks the given region is aligned to the size of a
hugepage. ia64 and powerpc define custom versions. The ia64 one simply
checks that the range is in the correct address space region in addition to
being suitably aligned. The powerpc version (just as previously) checks
for suitable addresses, and if necessary performs low-level MMU frobbing to
set up new areas for use by hugepages.
No libhugetlbfs testsuite regressions on ppc64 (POWER5 LPAR).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Zhang Yanmin <yanmin.zhang@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: William Lee Irwin III <wli@holomorphy.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
set_page_count usage outside mm/ is limited to setting the refcount to 1.
Remove set_page_count from outside mm/, and replace those users with
init_page_count() and set_page_refcounted().
This allows more debug checking, and tighter control on how code is allowed
to play around with page->_count.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Original 2.6.9 patch and explanation from somewhere within HP via
bugzilla...
ia64 stores a success/failure code in r10, and the return value (normal
return, or *positive* errno) in r8. The patch also sets the exit code to
negative errno if it's a failure result for consistency with other
architectures.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
A pte may be zapped by the swapper, exiting process, unmapping or page
migration while the accessed or dirty bit handers are about to run. In that
case the accessed bit or dirty is set on an zeroed pte which leads the VM to
conclude that this is a swap pte. This may lead to
- Messages from the vm like
swap_free: Bad swap file entry 4000000000000000
- Processes being aborted
swap_dup: Bad swap file entry 4000000000000000
VM: killing process ....
Page migration is particular suitable for the creation of this race since
it needs to remove and restore page table entries.
The fix here is to check for the present bit and simply not update
the pte if the page is not present anymore. If the page is not present
then the fault handler should run next which will take care of the problem
by bringing the page back and then mark the page dirty or move it onto the
active list.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
When there is no bus check, the return code should be failure, not success.
Signed-off-by: Russ Anderson (rja@sgi.com)
Signed-off-by: Tony Luck <tony.luck@intel.com>
This stuff is all in the generic ia64 kernel, and the new initcall error
reporting complains about them.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Turn on CONFIG_PNPACPI. I recently removed 8250_acpi.c. All devices
previously claimed by 8250_acpi.c should now be claimed by 8250_pnp.c.
This depends on having CONFIG_PNPACPI so ACPI devices show up as PNP
devices.
All other ia64 defconfigs either have CONFIG_PNPACPI already, or
don't have 8250 support turned on at all.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The MCA recovery messages are currently KERN_DEBUG,
so they don't show up in /var/log/messages (by default).
Increase the severity to KERN_ERR, for the initial
message (and also add the physical address to this
message). Leave the successful isolation message as
KERN_DEBUG, but increase the severity when isolation
fails to KERN_CRIT.
[Russ' patch made these all KERN_CRIT]
Signed-off-by: Russ Anderson (rja@sgi.com)
Signed-off-by: Tony Luck <tony.luck@intel.com>
The kbuild system takes advantage of an incorrect behavior in GNU make.
Once this behavior is fixed, all files in the kernel rebuild every time,
even if nothing has changed. This patch ensures kbuild works with both
the incorrect and correct behaviors of GNU make.
For more details on the incorrect behavior, see:
http://lists.gnu.org/archive/html/bug-make/2006-03/msg00003.html
Changes in this patch:
- Keep all targets that are to be marked .PHONY in a variable, PHONY.
- Add .PHONY: $(PHONY) to mark them properly.
- Remove any $(PHONY) files from the $? list when determining whether
targets are up-to-date or not.
Signed-off-by: Paul Smith <psmith@gnu.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Allow sysadmin to disable all warnings about userland apps
making unaligned accesses by using:
# echo 1 > /proc/sys/kernel/ignore-unaligned-usertrap
Rather than having to use prctl on a process by process basis.
Default behaivour leaves the warnings enabled.
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
beautify coding style for zeroing end of fsyscall_table entries.
Remove misleading __NR_syscall_last and add more comments.
Drop (now unneeded) "guard against failure to increase NR_syscalls"
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
arch/ia64/kernel/unaligned.c erroneously marked die_if_kernel()
with a "noreturn" attribute ... which is silly (it returns whenever
the argument regs say that the fault happened in user mode, as one
might expect given the "if_kernel" part of its name!). Thanks to
Alan and Gareth for pointing this out.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Christoph Hellwig <hch@infradead.org> pointed that there are no
in-tree uses of this. So revert 9c65cb9be6
Signed-off-by: Tony Luck <tony.luck@intel.com>
pcibios_setup() should return NULL if it handled a parameter. Since ia64
handles no parameters, it should return the string that was passed in,
not NULL. This brings ia64 into line with all other architectures that
handle no parameters.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Take advantage of kzalloc() as well as reduce the size of code generated
for the error returns in xpc_setup_infrastructure().
Signed-off-by: Jes Sorensen <jes@sgi.com>
Acked-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
unaligned_access does fetch cr.ipsr, then calls
dispatch_unaligned_handler, but dispatch_unaligned_handler fetches
cr.ipsr again, so delete the first one.
Signed-off-by: Zhang Yanmin <yanmin.zhang@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Commit 9ec4b1f356 made kprobes not compile
without module support, so just make that clear in the Kconfig file.
Also, since it's marked EXPERIMENTAL, make that dependency explicit too.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Minor updates to earlier patch.
- Added to documentation to add ia64 as well.
- Minor clarification on how to use disabled cpus
- used plain max instead of max_t per Andew Morton.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
It appears that if auditing is enabled, the kernel fails to
check for pending signals before returning to user mode.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Acked-by: Ken Chen <kenneth.w.chen@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Trivial port of this feature from i386
As it stands, panic_on_oops but does nothing on ia64
Signed-Off-By: Horms <horms@verge.net.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The original ia64 udelay() was simple, but flawed for platforms without
synchronized ITCs: a preemption and migration to another CPU during the
while-loop likely resulted in too-early termination or very, very
lengthy looping.
The first fix (now in 2.6.15) broke the delay loop into smaller,
non-preemptible chunks, reenabling preemption between the chunks. This
fix is flawed in that the total udelay is computed to be the sum of just
the non-premptible while-loop pieces, i.e., not counting the time spent
in the interim preemptible periods. If an interrupt or a migration
occurs during one of these interim periods, then that time is invisible
and only serves to lengthen the effective udelay().
This new fix backs out the current flawed fix and returns to a simple
udelay(), fully preemptible and interruptible. It implements two simple
alternative udelay() routines: one a default generic version that uses
ia64_get_itc(), and the other an sn-specific version that uses that
platform's RTC.
Signed-off-by: John Hawkes <hawkes@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Fix XPC so that it does not deliver any messages until the connected
callout has returned, as well as, prevent the disconnected callout to
occur before the disconnecting callout has returned.
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The __sn_cnodeid_to_nasid array was incorrectly sized at MAX_NUMNODES.
On a large system, this array could overflow. The following patch
corrects this by defining it to MAX_COMPACT_NODES.
Signed-off-by: Dean Roe <roe@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This one falls into the "present for Andrew Morton" category to address
his wishlist for a compiler warning free build ;-)
Signed-off-by: Tony Luck <tony.luck@intel.com>
General SN2 code cleanup:
- Do not initialize global variables to zero
- Use kzalloc instead of kmalloc+memset
- Check kmalloc return values
- Do not obfuscate spin lock calls
- Remove some unused code
- Various formatting cleanups
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Remove symbol exports from ia64_ksyms.c that are already exported in
lib/string.c.
Signed-off-by: Andreas Schwab <schwab@suse.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Have a facility to account for potentially hot-pluggable CPUs. ACPI doesnt
give a determinstic method to find hot-pluggable CPUs. Hence we use 2 methods
to assist.
- BIOS can mark potentially hot-pluggable CPUs as disabled in the MADT tables.
- User can specify the number of hot-pluggable CPUs via parameter
additional_cpus=X
The option is enabled only if ACPI_CONFIG_HOTPLUG_CPU=y which enables the
physical hotplug option. Without which user can still use logical onlining
and offlining of CPUs by enabling CONFIG_HOTPLUG_CPU=y
Adds more bits to cpu_possible_map for potentially hot-pluggable cpus.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Do not set cpu_possible_map for NR_CPUS when ACPI_CONFIG_HOTPLUG_CPU is set.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
MCA driver can cause panic if kernel gets a state info with no minstate.
This patch adds minstate validation before handling it.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Remove an erroneous kfree, and unlink the pcidev_info struct from the
pcidev_info list prior to free'ing the pcidev_info struct.
Signed-off-by: Prarit Bhargava <prarit@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Registers system call for the ia64 architecture.
Reserves space for ppoll and pselect, and adds unshare at system
call number 1296.
Signed-off-by: Janak Desai <janak@us.ibm.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
No platform in the community tree uses PLATFORM_MCA_HANDLERS, remove
the references.
Signed-off-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Update the comm field on the MCA handler for user tasks as well as for
verified kernel tasks. This helps to identify the task that was
running when the MCA occurred.
Signed-off-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Print a message identifying the monarch MCA handler. Print a summary
of the status of the slave MCA cpus.
Signed-off-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Prevent SN2 specific code to be executed on non SN2 platforms when
running a generic kernel.
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
There were two problems with enabling the PRINTK_TIME config
option:
1) The first calls to printk() occur before per-cpu data virtual
address is pinned into the TLB, so sched_clock() can fault.
2) sched_clock() is based on ar.itc, which may not be synchronized
across cpus.
Ken Chen started this patch, Tony Luck tinkered with it, and Jes
Sorensen perfected it.
Signed-off-by: Tony Luck <tony.luck@intel.com>
The check of (end != cp) after memparse in efi.c looks wrong to me.
The result is that we can't use mem= and max_addr= kernel parameter at
the same time.
The following patch removed the check just like other arches do.
Signed-off-by: Zou Nan hai <nanhai.zou@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Rewrite the SN pio_phys_xxx macros in assembly language. This
avoids issues with the Intel icc compiler. Function call
overhead is not an issue - the functions reference PIOs
and take 100's nsec to complete.
In addition, the functions should likely be in assembly
language anyway - they reference memory using physical
addressing mode. One function executes with psr.ic disabled.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
After converting the cpu physical address to shub2 physical
addressing, the address was run through TO_PHYS() which
clobbered a high node offset bit causing the BTE to fail
on shub2 nodes with large memory. This fix corrects
that problem.
Signed-off-by: Russ Anderson (rja@sgi.com)
Signed-off-by: Tony Luck <tony.luck@intel.com>
The patch implements cpu topology exportation by sysfs.
Items (attributes) are similar to /proc/cpuinfo.
1) /sys/devices/system/cpu/cpuX/topology/physical_package_id:
represent the physical package id of cpu X;
2) /sys/devices/system/cpu/cpuX/topology/core_id:
represent the cpu core id to cpu X;
3) /sys/devices/system/cpu/cpuX/topology/thread_siblings:
represent the thread siblings to cpu X in the same core;
4) /sys/devices/system/cpu/cpuX/topology/core_siblings:
represent the thread siblings to cpu X in the same physical package;
To implement it in an architecture-neutral way, a new source file,
driver/base/topology.c, is to export the 5 attributes.
If one architecture wants to support this feature, it just needs to
implement 4 defines, typically in file include/asm-XXX/topology.h.
The 4 defines are:
#define topology_physical_package_id(cpu)
#define topology_core_id(cpu)
#define topology_thread_siblings(cpu)
#define topology_core_siblings(cpu)
The type of **_id is int.
The type of siblings is cpumask_t.
To be consistent on all architectures, the 4 attributes should have
deafult values if their values are unavailable. Below is the rule.
1) physical_package_id: If cpu has no physical package id, -1 is the
default value.
2) core_id: If cpu doesn't support multi-core, its core id is 0.
3) thread_siblings: Just include itself, if the cpu doesn't support
HT/multi-thread.
4) core_siblings: Just include itself, if the cpu doesn't support
multi-core and HT/Multi-thread.
So be careful when declaring the 4 defines in include/asm-XXX/topology.h.
If an attribute isn't defined on an architecture, it won't be exported.
Thank Nathan, Greg, Andi, Paul and Venki.
The patch provides defines for i386/x86_64/ia64.
Signed-off-by: Zhang, Yanmin <yanmin.zhang@intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
During some testing, we got a warning about trying to allocate
memory while holding a lock. This fixes that problem.
Signed-off-by: Robin Holt <holt@sgi.com>
Acked-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Maintenance patch:
- Add missing __init calls
- Do not zero initialize global variables
- No need to typecast function call returns to void
- Some formatting
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
David Gibson