Chipsets with hardware based connection monitoring need to autonomically
send directed probe-request frames to the AP (in the event of beacon loss,
for example.)
For the hardware to be able to do this, it requires a template for the frame
to transmit to the AP, filled in with the BSSID and SSID of the AP, but also
the supported rate IE's.
This patch adds a function to mac80211, which allows the hardware driver to
fetch this template after association, so it can be configured to the hardware.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow antenna configuration by calling driver's function for it.
We disallow antenna configuration if the wiphy is already running, mainly to
make life easier for 802.11n drivers which need to recalculate HT capabilites.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow setting of TX and RX antennas configuration via nl80211.
The antenna configuration is defined as a bitmap of allowed antennas to use.
This API can be used to mask out antennas which are not attached or should not
be used for other reasons like regulatory concerns or special setups.
Separate bitmaps are used for RX and TX to allow configuring different antennas
for receiving and transmitting. Each bitmap is 32 bit long, each bit
representing one antenna, starting with antenna 1 at the first bit. If an
antenna bit is set, this means the driver is allowed to use this antenna for RX
or TX respectively; if the bit is not set the hardware is not allowed to use
this antenna.
Using bitmaps has the benefit of allowing for a flexible configuration
interface which can support many different configurations and which can be used
for 802.11n as well as non-802.11n devices. Instead of relying on some hardware
specific assumptions, drivers can use this information to know which antennas
are actually attached to the system and derive their capabilities based on
that.
802.11n devices should enable or disable chains, based on which antennas are
present (If all antennas belonging to a particular chain are disabled, the
entire chain should be disabled). HT capabilities (like STBC, TX Beamforming,
Antenna selection) should be calculated based on the available chains after
applying the antenna masks. Should a 802.11n device have diversity antennas
attached to one of their chains, diversity can be enabled or disabled based on
the antenna information.
Non-802.11n drivers can use the antenna masks to select RX and TX antennas and
to enable or disable antenna diversity.
While covering chainmasks for 802.11n and the standard "legacy" modes "fixed
antenna 1", "fixed antenna 2" and "diversity" this API also allows more rare,
but useful configurations as follows:
1) Send on antenna 1, receive on antenna 2 (or vice versa). This can be used to
have a low gain antenna for TX in order to keep within the regulatory
constraints and a high gain antenna for RX in order to receive weaker signals
("speak softly, but listen harder"). This can be useful for building long-shot
outdoor links. Another usage of this setup is having a low-noise pre-amplifier
on antenna 1 and a power amplifier on the other antenna. This way transmit
noise is mostly kept out of the low noise receive channel.
(This would be bitmaps: tx 1 rx 2).
2) Another similar setup is: Use RX diversity on both antennas, but always send
on antenna 1. Again that would allow us to benefit from a higher gain RX
antenna, while staying within the legal limits.
(This would be: tx 0 rx 3).
3) And finally there can be special experimental setups in research and
development even with pre 802.11n hardware where more than 2 antennas are
available. It's good to keep the API simple, yet flexible.
Signed-off-by: Bruno Randolf <br1@einfach.org>
--
v7: Made bitmasks 32 bit wide and rebased to latest wireless-testing.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The lower driver is notified when the fragmentation threshold changes
and upon a reconfig of the interface.
If the driver supports hardware TX fragmentation, don't fragment
packets in the stack.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We should be enabling country IE hints for WIPHY_FLAG_STRICT_REGULATORY
even if we haven't yet recieved regulatory domain hint for the driver
if it needed one. Without this Country IEs are not passed on to drivers
that have set WIPHY_FLAG_STRICT_REGULATORY, today this is just all
Atheros chipset drivers: ath5k, ath9k, ar9170, carl9170.
This was part of the original design, however it was completely
overlooked...
Cc: Easwar Krishnan <easwar.krishnan@atheros.com>
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we stop a namespace we flush the table and free one, but the
added fn_zone-s (and their hashes if grown) are leaked. Need to free.
Tries releases all its stuff in the flushing code.
Shame on us - this bug exists since the very first make-fib-per-net
patches in 2.6.27 :(
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
SYNOPSIS
size[4] Tfsync tag[2] fid[4] datasync[4]
size[4] Rfsync tag[2]
DESCRIPTION
The Tfsync transaction transfers ("flushes") all modified in-core data of
file identified by fid to the disk device (or other permanent storage
device) where that file resides.
If datasync flag is specified data will be fleshed but does not flush
modified metadata unless that metadata is needed in order to allow a
subsequent data retrieval to be correctly handled.
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Synopsis
size[4] TReadlink tag[2] fid[4]
size[4] RReadlink tag[2] target[s]
Description
Readlink is used to return the contents of the symoblic link
referred by fid. Contents of symboic link is returned as a
response.
target[s] - Contents of the symbolic link referred by fid.
Signed-off-by: M. Mohan Kumar <mohan@in.ibm.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Synopsis
size[4] TGetlock tag[2] fid[4] getlock[n]
size[4] RGetlock tag[2] getlock[n]
Description
TGetlock is used to test for the existence of byte range posix locks on a file
identified by given fid. The reply contains getlock structure. If the lock could
be placed it returns F_UNLCK in type field of getlock structure. Otherwise it
returns the details of the conflicting locks in the getlock structure
getlock structure:
type[1] - Type of lock: F_RDLCK, F_WRLCK
start[8] - Starting offset for lock
length[8] - Number of bytes to check for the lock
If length is 0, check for lock in all bytes starting at the location
'start' through to the end of file
pid[4] - PID of the process that wants to take lock/owns the task
in case of reply
client[4] - Client id of the system that owns the process which
has the conflicting lock
Signed-off-by: M. Mohan Kumar <mohan@in.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Synopsis
size[4] TLock tag[2] fid[4] flock[n]
size[4] RLock tag[2] status[1]
Description
Tlock is used to acquire/release byte range posix locks on a file
identified by given fid. The reply contains status of the lock request
flock structure:
type[1] - Type of lock: F_RDLCK, F_WRLCK, F_UNLCK
flags[4] - Flags could be either of
P9_LOCK_FLAGS_BLOCK - Blocked lock request, if there is a
conflicting lock exists, wait for that lock to be released.
P9_LOCK_FLAGS_RECLAIM - Reclaim lock request, used when client is
trying to reclaim a lock after a server restrart (due to crash)
start[8] - Starting offset for lock
length[8] - Number of bytes to lock
If length is 0, lock all bytes starting at the location 'start'
through to the end of file
pid[4] - PID of the process that wants to take lock
client_id[4] - Unique client id
status[1] - Status of the lock request, can be
P9_LOCK_SUCCESS(0), P9_LOCK_BLOCKED(1), P9_LOCK_ERROR(2) or
P9_LOCK_GRACE(3)
P9_LOCK_SUCCESS - Request was successful
P9_LOCK_BLOCKED - A conflicting lock is held by another process
P9_LOCK_ERROR - Error while processing the lock request
P9_LOCK_GRACE - Server is in grace period, it can't accept new lock
requests in this period (except locks with
P9_LOCK_FLAGS_RECLAIM flag set)
Signed-off-by: M. Mohan Kumar <mohan@in.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
SYNOPSIS
size[4] Tfsync tag[2] fid[4]
size[4] Rfsync tag[2]
DESCRIPTION
The Tfsync transaction transfers ("flushes") all modified in-core data of
file identified by fid to the disk device (or other permanent storage
device) where that file resides.
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Signed-off-by: Arun R Bharadwaj <arun@linux.vnet.ibm.com>
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Adds __rcu annotations to inetpeer
(struct inet_peer)->avl_left
(struct inet_peer)->avl_right
This is a tedious cleanup, but removes one smp_wmb() from link_to_pool()
since we now use more self documenting rcu_assign_pointer().
Note the use of RCU_INIT_POINTER() instead of rcu_assign_pointer() in
all cases we dont need a memory barrier.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds __rcu annotation to (struct fib_rule)->ctarget
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add __rcu annotations to :
(struct ip_tunnel)->prl
(struct ip_tunnel_prl_entry)->next
(struct xfrm_tunnel)->next
struct xfrm_tunnel *tunnel4_handlers
struct xfrm_tunnel *tunnel64_handlers
And use appropriate rcu primitives to reduce sparse warnings if
CONFIG_SPARSE_RCU_POINTER=y
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add __rcu annotations to :
struct net_protocol *inet_protos
struct net_protocol *inet6_protos
And use appropriate casts to reduce sparse warnings if
CONFIG_SPARSE_RCU_POINTER=y
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add __rcu annotations to :
(struct dst_entry)->rt_next
(struct rt_hash_bucket)->chain
And use appropriate rcu primitives to reduce sparse warnings if
CONFIG_SPARSE_RCU_POINTER=y
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add __rcu annotations to :
(struct ip_ra_chain)->next
struct ip_ra_chain *ip_ra_chain;
And use appropriate rcu primitives.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add __rcu annotation to :
(struct sock)->sk_filter
And use appropriate rcu primitives to reduce sparse warnings if
CONFIG_SPARSE_RCU_POINTER=y
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
add __rcu annotation to (struct net)->gen, and use
rcu_dereference_protected() in net_assign_generic()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
(struct ip6_tnl)->next is rcu protected :
(struct ip_tunnel)->next is rcu protected :
(struct xfrm6_tunnel)->next is rcu protected :
add __rcu annotation and proper rcu primitives.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
(struct net_device)->garp_port is rcu protected :
(struct garp_port)->applicants is rcu protected :
add __rcu annotation and proper rcu primitives.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just like with IPv4, we need access to the UDP hash table to look up local
sockets, but instead of exporting the global udp_table, export a lookup
function.
Signed-off-by: Balazs Scheidler <bazsi@balabit.hu>
Signed-off-by: KOVACS Krisztian <hidden@balabit.hu>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Like with IPv4, TProxy needs IPv6 defragmentation but does not
require connection tracking. Since defragmentation was coupled
with conntrack, I split off the two, creating an nf_defrag_ipv6 module,
similar to the already existing nf_defrag_ipv4.
Signed-off-by: Balazs Scheidler <bazsi@balabit.hu>
Signed-off-by: KOVACS Krisztian <hidden@balabit.hu>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Make p9_client_version static since only used in one file.
Remove p9_client_auth because it is defined but never used.
Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When __inet_inherit_port() is called on a tproxy connection the wrong locks are
held for the inet_bind_bucket it is added to. __inet_inherit_port() made an
implicit assumption that the listener's port number (and thus its bind bucket).
Unfortunately, if you're using the TPROXY target to redirect skbs to a
transparent proxy that assumption is not true anymore and things break.
This patch adds code to __inet_inherit_port() so that it can handle this case
by looking up or creating a new bind bucket for the child socket and updates
callers of __inet_inherit_port() to gracefully handle __inet_inherit_port()
failing.
Reported by and original patch from Stephen Buck <stephen.buck@exinda.com>.
See http://marc.info/?t=128169268200001&r=1&w=2 for the original discussion.
Signed-off-by: KOVACS Krisztian <hidden@balabit.hu>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Also, inline this function as the lookup_type is always a literal
and inlining removes branches performed at runtime.
Signed-off-by: Balazs Scheidler <bazsi@balabit.hu>
Signed-off-by: KOVACS Krisztian <hidden@balabit.hu>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Without tproxy redirections an incoming SYN kicks out conflicting
TIME_WAIT sockets, in order to handle clients that reuse ports
within the TIME_WAIT period.
The same mechanism didn't work in case TProxy is involved in finding
the proper socket, as the time_wait processing code looked up the
listening socket assuming that the listener addr/port matches those
of the established connection.
This is not the case with TProxy as the listener addr/port is possibly
changed with the tproxy rule.
Signed-off-by: Balazs Scheidler <bazsi@balabit.hu>
Signed-off-by: KOVACS Krisztian <hidden@balabit.hu>
Signed-off-by: Patrick McHardy <kaber@trash.net>
The first parameter dev isn't in use in qdisc_create_dflt().
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Acked-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function rtnl_kill_links is defined but never used.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function only defined and used in one file.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As skb->protocol is not valid in LOCAL_OUT add
parameter for address family in packet debugging functions.
Even if ports are not present in AH and ESP change them to
use ip_vs_tcpudp_debug_packet to show at least valid addresses
as before. This patch removes the last user of skb->protocol
in IPVS.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
This patch deals with local real servers:
- Add support for DNAT to local address (different real server port).
It needs ip_vs_out hook in LOCAL_OUT for both families because
skb->protocol is not set for locally generated packets and can not
be used to set 'af'.
- Skip packets in ip_vs_in marked with skb->ipvs_property because
ip_vs_out processing can be executed in LOCAL_OUT but we still
have the conn_out_get check in ip_vs_in.
- Ignore packets with inet->nodefrag from local stack
- Require skb_dst(skb) != NULL because we use it to get struct net
- Add support for changing the route to local IPv4 stack after DNAT
depending on the source address type. Local client sets output
route and the remote client sets input route. It looks like
IPv6 does not need such rerouting because the replies use
addresses from initial incoming header, not from skb route.
- All transmitters now have strict checks for the destination
address type: redirect from non-local address to local real
server requires NAT method, local address can not be used as
source address when talking to remote real server.
- Now LOCALNODE is not set explicitly as forwarding
method in real server to allow the connections to provide
correct forwarding method to the backup server. Not sure if
this breaks tools that expect to see 'Local' real server type.
If needed, this can be supported with new flag IP_VS_DEST_F_LOCAL.
Now it should be possible connections in backup that lost
their fwmark information during sync to be forwarded properly
to their daddr, even if it is local address in the backup server.
By this way backup could be used as real server for DR or TUN,
for NAT there are some restrictions because tuple collisions
in conntracks can create problems for the traffic.
- Call ip_vs_dst_reset when destination is updated in case
some real server IP type is changed between local and remote.
[ horms@verge.net.au: removed trailing whitespace ]
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
This patch is needed to avoid scheduling of
packets from local real server when we add ip_vs_in
in LOCAL_OUT hook to support local client.
Currently, when ip_vs_in can not find existing
connection it tries to create new one by calling ip_vs_schedule.
The default indication from ip_vs_schedule was if
connection was scheduled to real server. If real server is
not available we try to use the bypass forwarding method
or to send ICMP error. But in some cases we do not want to use
the bypass feature. So, add flag 'ignored' to indicate if
the scheduler ignores this packet.
Make sure we do not create new connections from replies.
We can hit this problem for persistent services and local real
server when ip_vs_in is added to LOCAL_OUT hook to handle
local clients.
Also, make sure ip_vs_schedule ignores SYN packets
for Active FTP DATA from local real server. The FTP DATA
connection should be created on SYN+ACK from client to assign
correct connection daddr.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Change skb->ipvs_property semantic. This is preparation
to support ip_vs_out processing in LOCAL_OUT. ipvs_property=1
will be used to avoid expensive lookups for traffic sent by
transmitters. Now when conntrack support is not used we call
ip_vs_notrack method to avoid problems in OUTPUT and
POST_ROUTING hooks instead of exiting POST_ROUTING as before.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Avoid full checksum calculation for apps that can provide
info whether csum was broken after payload mangling. For now only
ip_vs_ftp mangles payload and it updates the csum, so the full
recalculation is avoided for all packets.
Add CHECKSUM_UNNECESSARY for snat_handler (TCP and UDP).
It is needed to support SNAT from local address for the case
when csum is fully recalculated.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
IPv6 encapsulation uses a bad source address for the tunnel.
i.e. VIP will be used as local-addr and encap. dst addr.
Decapsulation will not accept this.
Example
LVS (eth1 2003::2:0:1/96, VIP 2003::2:0:100)
(eth0 2003::1:0:1/96)
RS (ethX 2003::1:0:5/96)
tcpdump
2003::2:0:100 > 2003::1:0:5: IP6 (hlim 63, next-header TCP (6) payload length: 40) 2003::3:0:10.50991 > 2003::2:0:100.http: Flags [S], cksum 0x7312 (correct), seq 3006460279, win 5760, options [mss 1440,sackOK,TS val 1904932 ecr 0,nop,wscale 3], length 0
In Linux IPv6 impl. you can't have a tunnel with an any cast address
receiving packets (I have not tried to interpret RFC 2473)
To have receive capabilities the tunnel must have:
- Local address set as multicast addr or an unicast addr
- Remote address set as an unicast addr.
- Loop back addres or Link local address are not allowed.
This causes us to setup a tunnel in the Real Server with the
LVS as the remote address, here you can't use the VIP address since it's
used inside the tunnel.
Solution
Use outgoing interface IPv6 address (match against the destination).
i.e. use ip6_route_output() to look up the route cache and
then use ipv6_dev_get_saddr(...) to set the source address of the
encapsulated packet.
Additionally, cache the results in new destination
fields: dst_cookie and dst_saddr and properly check the
returned dst from ip6_route_output. We now add xfrm_lookup
call only for the tunneling method where the source address
is a local one.
Signed-off-by:Hans Schillstrom <hans.schillstrom@ericsson.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patch allows to listen to events that inform about
expectations destroyed.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
In a network bench, I noticed an unfortunate false sharing between
'loopback_dev' and 'count' fields in "struct net".
'count' is written each time a socket is created or destroyed, while
loopback_dev might be often read in routing code.
Move loopback_dev in a read mostly section of "struct net"
Note: struct netns_xfrm is cache line aligned on SMP.
(It contains a "struct dst_ops")
Move it at the end to avoid holes, and reduce sizeof(struct net) by 128
bytes on ia32.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do some cleanups of TIPC based on make namespacecheck
1. Don't export unused symbols
2. Eliminate dead code
3. Make functions and variables local
4. Rename buf_acquire to tipc_buf_acquire since it is used in several files
Compile tested only.
This make break out of tree kernel modules that depend on TIPC routines.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on suggestion by Rémi Denis-Courmont to implement 'connect'
for Pipe controller logic, this patch implements 'connect' socket
call for the Pipe controller logic.
The patch does following:-
- Removes setsockopts for PNPIPE_CREATE and PNPIPE_DESTROY
- Adds setsockopt for setting the Pipe handle value
- Implements connect socket call
- Updates the Pipe controller logic
User-space should now follow below sequence with Pipe controller:-
-socket
-bind
-setsockopt for PNPIPE_PIPE_HANDLE
-connect
-setsockopt for PNPIPE_ENCAP_IP
-setsockopt for PNPIPE_ENABLE
GPRS/3G data has been tested working fine with this.
Signed-off-by: Kumar Sanghvi <kumar.sanghvi@stericsson.com>
Acked-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using the frame registration notification, we
can see when probe requests are requested and
notify the low-level driver via filtering. The
flag is also set in AP and IBSS modes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers may need to adjust their filters according
to frame registrations, so notify them about them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This commit adds a bt_sock_stream_recvmsg() function for use by any
Bluetooth code that uses SOCK_STREAM sockets. This code is copied
from rfcomm_sock_recvmsg() with minimal modifications to remove
RFCOMM-specific functionality and improve readability.
L2CAP (with the SOCK_STREAM socket type) and RFCOMM have common needs
when it comes to reading data. Proper stream read semantics require
that applications can read from a stream one byte at a time and not
lose any data. The RFCOMM code already operated on and pulled data
from the underlying L2CAP socket, so very few changes were required to
make the code more generic for use with non-RFCOMM data over L2CAP.
Applications that need more awareness of L2CAP frame boundaries are
still free to use SOCK_SEQPACKET sockets, and may verify that they
connection did not fall back to basic mode by calling getsockopt().
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Felix Fietkau