Untested, but this should fix up the bulk of the totally mechanical
issues, and should make the actual detail fixing easier.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch makes the AT91 gpio.c support processor-generic (AT91RM9200
and AT91SAM9xxx). The GPIO controllers supported by a particular AT91
processor are defined in the processor-specific file and are registered
with gpio.c at startup.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is more preparation for adding support for the new Atmel AT91SAM9
processors.
Changes include:
- Replace AT91_BASE_* with AT91RM9200_BASE_*
- Replace AT91_ID_* with AT91RM9200_ID_*
- ROM, SRAM and UHP address definitions moved to at91rm9200.h.
- The raw AT91_P[ABCD]_* definitions are now depreciated in favour of
the GPIO API.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from David Brownell
ARM genirq cleanups/updates:
- Start switching platforms to newer APIs
* use "irq_chip" name, not "irqchip"
* providing irq_chip.name
- Show irq_chip.name in /proc/interrupts, like on x86.
This update a bit more than half of the ARM code. The irq_chip.name
values were chosen to match docs (if I have them) or be otherwise
obvious ("FPGA", "CPLD", or matching the code).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Thomas Gleixner
From: Thomas Gleixner <tglx@linutronix.de>
Fixup the conversion to generic irq subsystem.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
This patch adds suspend/resume/set_wake support for the AT91RM9200's
GPIO interrupts.
Original patch from David Brownell.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In all current use cases, "chipdata" is used to store an iomem address.
Mark it with __iomem, and rename it to 'base'. Leave the accessor macros
alone.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
disable_irq() lazily disables the interrupt, so the IRQ is only disabled
once the interrupt occurs again. The GPIO interrupt handler therefore
must first check disable_depth to see if the IRQ needs to be disabled.
Orignal patch by Bill Gatliff.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
This patch adds the at91_set_multi_drive() function to enable/disable
the multi-drive (open collector) pin capability on the AT91RM9200
processor.
This is necessary to fix the UDC (USB Gadget) driver for the AT91RM9200
board as it will not allow the board reset line to be pulled low if the
pullup is not driven as an open collector output as the boards are wired
to the USB connector on both the DK/EK.
This version of the patch updates it to 2.6.16-rc4.
Orignal patch by Jeff Warren.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from SAN People
Following changes were made to clock.c:
1) Replaced <asm/hardware/clock.h> with <linux/clk.h>
2) Removed old unused clk_enable & clk_disable.
3) Replaced clk_use/clk_unuse with clk_enable/clk_disable.
Otherwise it's the same as the previous patch.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linus Torvalds