MII_M1111_HWCFG_FIBER_COPPER_RES is a bit of MII_M1111_PHY_EXT_SR, not
MII_M1111_PHY_EXT_CR.
Signed-off-by: Wang Jian <lark@linux.net.cn>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The 27.15 bit (MII_M1111_HWCFG_FIBER_COPPER_AUTO) is disable bit. When
set to 1, copper/fiber auto selection is disabled. The current code
to enable but actually disable auto selection.
Signed-off-by: Wang Jian <lark@linux.net.cn>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The other if blocks don't redeclare temp, remove the redeclaration in
the final if() block.
drivers/net/phy/marvell.c:214:7: warning: symbol 'temp' shadows an earlier one
drivers/net/phy/marvell.c:160:6: originally declared here
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Marvell PHY m88e1111 (not sure about other models, but think they too)
works in two modes: fiber and copper. In Marvell PHY driver (that we
have in current community kernels) code supported only copper mode,
and this is not configurable, bits for copper mode are simply written
in registers during PHY initialization.
This patch adds support for both modes.
Signed-off-by: Alexandr Smirnov <asmirnov@ru.mvista.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Previously, Internal Delay specification implied the delay be
applied to both TX and RX. This patch allows for separate TX/RX-only
internal delay specification.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Tested-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add PHY IDs for Marvell 88E1240. It seems to have close enough programming
models to 1111/1112 for basic support at least.
Also clean up whitespace in the ID list a bit.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add 88E1112 PHY ID to the marvell driver. Seems to do fine with the
88E1111 inits.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Simplify the marvell driver init a bit: Make the supported devices an
array instead of explicitly registering each structure. This makes it
considerably easier to add new devices down the road.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If connected via SGMII, initialize with SGMII mode configured.
Signed-off-by: Kapil Juneja <Kapil.Juneja@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Support for configuring RGMII-ID (RGMII with internal delay) mode on the
88e1111 and 88e1145. Ucc_geth on MPC8360EMDS(the main user of ucc_geth)
is broken after changed to use phylib. It is fixed by adding this
internal delay.
Also renamed 88e1111s -> 88e1111 (no references to an 88e1111s part were
found), and fixed some whitespace.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Changes include:
* New support for 88e1145
* New support for 88e111s
* Fixing 88e1101 driver to not match non-88e1101 PHYs
* Increases in feature support across Marvell PHY product line
* Fixes a bunch of whitespace issues found by Lindent
Signed-off-by: Andrew Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
After Al Viro (finally) succeeded in removing the sched.h #include in module.h
recently, it makes sense again to remove other superfluous sched.h includes.
There are quite a lot of files which include it but don't actually need
anything defined in there. Presumably these includes were once needed for
macros that used to live in sched.h, but moved to other header files in the
course of cleaning it up.
To ease the pain, this time I did not fiddle with any header files and only
removed #includes from .c-files, which tend to cause less trouble.
Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha,
arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig,
allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all
configs in arch/arm/configs on arm. I also checked that no new warnings were
introduced by the patch (actually, some warnings are removed that were emitted
by unnecessarily included header files).
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch requires the new support for configurable PHY
interfaces.
Changes include:
* New support for 88e1145
* New support for 88e111s
* Fixing 88e1101 driver to not match non-88e1101 PHYs
* Increases in feature support across Marvell PHY product line
* Fixes a bunch of whitespace issues found by Lindent
Signed-off-by: Andrew Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ethernet drivers to remain as ignorant as is reasonable of the connected
PHY's design and operation details.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Wang Jian