This patch (as626) makes some improvements to the debugging code in
uhci-hcd. The main change is that now the code won't get compiled if
CONFIG_USB_DEBUG isn't set. But there are other changes too, like
adding a missing .owner field and printing a debugging dump if the
controller dies.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As part of reorienting uhci-hcd away from URBs and toward endpoint
queues, this patch (as625) eliminates the driver's main list of URBs.
The list wsa used mainly in checking for URB completions; now the driver
goes through the list of active endpoints and checks the members of the
queues.
As a side effect, I had to remove the code that looks for FSBR timeouts.
For now, FSBR will remain on so long as any URBs on a full-speed control
or bulk queue request it, even if the queue isn't advancing. A later
patch can add more intelligent handling. This isn't a huge drawback;
it's pretty rare for an URB to get stuck for more than a fraction of a
second. (And it will help the people trying to use those insane HP USB
devices.)
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as624) fixes a hardware race in uhci-hcd by adding a dummy
TD to the end of each endpoint's queue. Without the dummy the host
controller will effectively turn off the queue when it reaches the end,
which happens asynchronously. This leads to a potential problem when
new transfer descriptors are added to the end of the queue; they may
never get used.
With a dummy TD present the controller never turns off the queue;
instead it just stops at the dummy and leaves the queue on but inactive.
When new TDs are added to the end of the queue, the first new one gets
written over the dummy. Thus there's never any question about whether
the queue is running or needs to be restarted.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as623) changes the uhci-hcd driver to make it use one QH per
device endpoint, instead of a QH per URB as it does now. Numerous areas
of the code are affected by this. For example, the distinction between
"queued" URBs and non-"queued" URBs no longer exists; all URBs belong to
a queue and some just happen to be at the queue's head.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as615b) edits a large number of comments in the uhci-hcd code,
mainly removing excess apostrophes.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
patch below marks various USB tables and variables as const so that they
end up in .rodata section and don't cacheline share with things that get
written to. For the non-array variables it also allows gcc to optimize
more.
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as563) splits the physical and logical framelist arrays in
uhci-hcd into two separate pieces. This will allow slightly better memory
utilization, since each piece is no larger than a single page whereas
before the whole thing was a little bigger than two pages. It also allows
the logical array to be allocated in non-DMA-coherent memory.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as562) removes from the uhci-hcd driver a few unused fields
and some unnecessary tests against NULL and assignments to NULL. In fact
it wasn't until fairly recently that the tests became unnecessary.
Before last winter it was possible that the driver's stop() routine would
get called even if the start() routine returned an error, but now that
can't happen. Hence there's no longer any need to check for partial
initialization.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch starts making some serious changes to the UHCI driver.
There's a set of private states for the root hub, and the internal
routines for suspending and resuming work completely differently, with
transitions based on the new states. Now the driver distinguishes
between a privately auto-stopped state and a publicly suspended state,
and it will properly suspend controllers with broken resume-detect
interrupts instead of resetting them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Alan Stern