Host adapter hardware imposes certain restrictions and features on
address ranges. Instead of hard-wire such ranges into the ieee1394
core or even into protocol drivers, let lowlevel drivers specify
these ranges via struct hpsb_host.
Patch "ohci1394: set address range properties" must be applied too,
else hpsb_allocate_and_register_addrspace() won't work properly.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Since broadcast transactions are already complete when the request has
been sent, the same transaction label can be reused all over again, see
IEEE 1394 7.3.2.5 and 6.2.4.3. Therefore we can reduce the footprint
of struct hpsb_host by the size of one struct hpsb_tlabel_pool.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Add support for the following types of hardware:
+ nodes that have a link speed < PHY speed
+ 1394b PHYs that are less than S800 capable
+ 1394b/1394a adapter cable between two 1394b PHYs
Also, S1600 and S3200 are now supported if IEEE1394_SPEED_MAX is raised.
A probing function is added to nodemgr's config ROM fetching routine
which adjusts the allowable speed if an access problem was encountered.
Pros and Cons of the approach:
+ minimum code footprint to support this less widely used hardware
+ nearly no overhead for unaffected hardware
- ineffective before nodemgr began to read the ROM of affected nodes
- ineffective if ieee1394 is loaded with disable_nodemgr=1
The speed map CSRs which are published to the bus are not touched by the
patch.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Hakan Ardo <hakan@debian.org>
Cc: Calculex <linux@calculex.com>
Cc: Robert J. Kosinski <robk@cmcherald.com>
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
After initializing an IEEE 1394 host, broadcast a resume packet. This makes
remote nodes visible which suspended their ports while the host was down.
Such nodes had to be unplugged and replugged in order to be recognized.
Motorola DCT6200 cable reciever was affected, probably other devices too.
http://marc.theaimsgroup.com/?t=113202715800001
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jody McIntyre <scjody@modernduck.com>
(cherry picked from 14c0fa243b commit)
After initializing an IEEE 1394 host, broadcast a resume packet. This makes
remote nodes visible which suspended their ports while the host was down.
Such nodes had to be unplugged and replugged in order to be recognized.
Motorola DCT6200 cable reciever was affected, probably other devices too.
http://marc.theaimsgroup.com/?t=113202715800001
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jody McIntyre <scjody@modernduck.com>
trivial edits of a few comments
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Ben Collins <bcollins@debian.org>
Signed-off-by: Jody McIntyre <scjody@steamballoon.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Ben Collins