Interrupt-remapping enables queued invalidation. And once queued invalidation
is enabled, IOTLB invalidation also needs to use the queued invalidation
mechanism and the register based IOTLB invalidation doesn't work.
For now, Support for IOTLB invalidation using queued invalidation is
missing. Meanwhile, disable DMA-remapping, if Interrupt-remapping
support is detected.
For the meanwhile, if someone wants to really enable DMA-remapping, they
can use nox2apic, which will disable interrupt-remapping and as such
doesn't enable queued invalidation.
And given that none of the release platforms support intr-remapping yet,
we should be ok for this temporary hack.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: akpm@linux-foundation.org
Cc: arjan@linux.intel.com
Cc: andi@firstfloor.org
Cc: ebiederm@xmission.com
Cc: jbarnes@virtuousgeek.org
Cc: steiner@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Queued invalidation (part of Intel Virtualization Technology for
Directed I/O architecture) infrastructure.
This will be used for invalidating the interrupt entry cache in the
case of Interrupt-remapping and IOTLB invalidation in the case
of DMA-remapping.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: akpm@linux-foundation.org
Cc: arjan@linux.intel.com
Cc: andi@firstfloor.org
Cc: ebiederm@xmission.com
Cc: jbarnes@virtuousgeek.org
Cc: steiner@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Allocate the iommu during the parse of DMA remapping hardware
definition structures. And also, introduce routines for device
scope initialization which will be explicitly called during
dma-remapping initialization.
These will be used for enabling interrupt remapping separately from the
existing DMA-remapping enabling sequence.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: akpm@linux-foundation.org
Cc: arjan@linux.intel.com
Cc: andi@firstfloor.org
Cc: ebiederm@xmission.com
Cc: jbarnes@virtuousgeek.org
Cc: steiner@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Clean up the intel-iommu code related to deferred iommu flush logic. There is
no need to allocate all the iommu's as a sequential array.
This will be used later in the interrupt-remapping patch series to
allocate iommu much early and individually for each device remapping
hardware unit.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: akpm@linux-foundation.org
Cc: arjan@linux.intel.com
Cc: andi@firstfloor.org
Cc: ebiederm@xmission.com
Cc: jbarnes@virtuousgeek.org
Cc: steiner@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
code reorganization of the generic Intel vt-d parsing related routines and linux
iommu routines specific to Intel vt-d.
drivers/pci/dmar.c now contains the generic vt-d parsing related routines
drivers/pci/intel_iommu.c contains the iommu routines specific to vt-d
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: akpm@linux-foundation.org
Cc: arjan@linux.intel.com
Cc: andi@firstfloor.org
Cc: ebiederm@xmission.com
Cc: jbarnes@virtuousgeek.org
Cc: steiner@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
gart.h has only GART-specific stuff. Only GART code needs it. Other
IOMMU stuff should include iommu.h instead of gart.h.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
first step: make the VISWS subarch boot on a regular PC.
We take various shortcuts for that. We copy the generic arch setup file over
into the VISWS setup file.
This is the only step that is not expected to boot on a real VISWS.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch just fixes the compiler warning:
drivers/pci/quirks.c: In function ‘quirk_reroute_to_boot_interrupts_intel’:
drivers/pci/quirks.c:1375: warning: unused variable ‘i’
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Cc: sassmann@suse.de
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Some chipsets (e.g. intel 6700PXH) generate a legacy INTx when the
IRQ entry in the chipset's IO-APIC is masked (as, e.g. the RT kernel
does during interrupt handling). On chipsets where this INTx generation
cannot be disabled, we reroute the valid interrupts to their legacy
equivalent to get rid of spurious interrupts that might otherwise bring
down (vital) interrupt lines through spurious interrupt detection in
note_interrupt().
This patch benefited from discussions with Alexander Graf, Torsten Duwe,
Ihno Krumreich, Daniel Gollub, Hannes Reinecke. The conclusions we drew
and the patch itself are the authors' responsibility alone.
Signed-off-by: Stefan Assmann <sassmann@suse.de>
Signed-off-by: Olaf Dabrunz <od@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add a quirk to disable legacy boot interrupt generation on intel devices
that support disabling it.
This patch benefited from discussions with Alexander Graf, Torsten Duwe,
Ihno Krumreich, Daniel Gollub, Hannes Reinecke. The conclusions we drew
and the patch itself are the authors' responsibility alone.
Signed-off-by: Stefan Assmann <sassmann@suse.de>
Signed-off-by: Olaf Dabrunz <od@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
want to remove arch_get_ram_range, and use early_node_map instead.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
If the offset of PCI device's PM capability in its configuration space,
the mask of states that the device supports PME# from and the D1 and D2
support bits are cached in the corresponding struct pci_dev, the PCI
device PM code can be simplified quite a bit.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Introduce functions pci_prepare_to_sleep() and pci_back_from_sleep(),
to be used by the PCI drivers that want to place their devices into
the lowest power state appropiate for them (PCI_D3hot, if the device
is not supposed to wake up the system, or the deepest state from
which the wake-up is possible, otherwise) while the system is being
prepared to go into a sleeping state and to put them back into D0
during the subsequent transition to the working state.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* Introduce function acpi_pm_device_sleep_wake() for enabling and
disabling the system wake-up capability of devices that are power
manageable by ACPI.
* Introduce function acpi_bus_can_wakeup() allowing other (dependent)
subsystems to check if ACPI is able to enable the system wake-up
capability of given device.
* Introduce callback .sleep_wake() in struct pci_platform_pm_ops and
for the ACPI PCI 'driver' make it use acpi_pm_device_sleep_wake().
* Introduce callback .can_wakeup() in struct pci_platform_pm_ops and
for the ACPI 'driver' make it use acpi_bus_can_wakeup().
* Move the PME# handlig code out of pci_enable_wake() and split it
into two functions, pci_pme_capable() and pci_pme_active(),
allowing the caller to check if given device is capable of
generating PME# from given power state and to enable/disable the
device's PME# functionality, respectively.
* Modify pci_enable_wake() to use the new ACPI callbacks and the new
PME#-related functions.
* Drop the generic .platform_enable_wakeup() callback that is not
used any more.
* Introduce device_set_wakeup_capable() that will set the
power.can_wakeup flag of given device.
* Rework PCI device PM initialization so that, if given device is
capable of generating wake-up events, either natively through the
PME# mechanism, or with the help of the platform, its
power.can_wakeup flag is set and its power.should_wakeup flag is
unset as appropriate.
* Make ACPI set the power.can_wakeup flag for devices found to be
wake-up capable by it.
* Make the ACPI wake-up code enable/disable GPEs for devices that
have the wakeup.flags.prepared flag set (which means that their
wake-up power has been enabled).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Rework pci_set_power_state() so that the platform callback is
invoked before the native mechanism, if necessary. Also, make
the function check if the device is power manageable by the
platform before invoking the platform callback.
This may matter if the device dependent on additional power
resources controlled by the platform is being put into D0, in which
case those power resources must be turned on before we attempt to
handle the device itself.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Introduce function pointer platform_pci_power_manageable to be used
by the platform-related code to point to a function allowing us to
check if given device is power manageable by the platform.
Introduce acpi_pci_power_manageable() playing that role for ACPI.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
It seems VT3336 can't do msi either as with its bro 3351. Disable it.
Reported in the following SUSE bug.
https://bugzilla.novell.com/show_bug.cgi?id=300001
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This changes pci_setup_device to handle pci_name() now returning a
constant string.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
During the development of the physical PCI slot patch series, Gary Hade
kept on reporting strange oopses due to interactions between pci_slot
and acpiphp.
http://lkml.org/lkml/2007/11/28/319
find_root_bridges() unconditionally installs
handle_hotplug_event_bridge() as an ACPI_SYSTEM_NOTIFY handler for all
root bridges.
However, during module cleanup, remove_bridge() will only remove the
notify handler iff the root bridge had a hot-pluggable slot directly
underneath. That is:
root bridge -> hotplug slot
But, if the topology looks like either of the following:
root bridge -> non-hotplug slot
root bridge -> p2p bridge -> hotplug slot
Then we currently do not remove the notify handler from that root
bridge.
This can cause a kernel oops if we modprobe acpiphp later and it gets
loaded somewhere else in memory. If the root bridge then receives a
hotplug event, it will then attempt to call a stale, non-existent notify
handler and we blow up.
Much thanks goes to Gary Hade for his persistent debugging efforts.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Gary Hade <garyhade@us.ibm.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
For Broadcom 5706, 5708, 5709 rev. A nics, any read beyond the
VPD end tag will hang the device. This problem was initially
observed when a vpd entry was created in sysfs
('/sys/bus/pci/devices/<id>/vpd'). A read to this sysfs entry
will dump 32k of data. Reading a full 32k will cause an access
beyond the VPD end tag causing the device to hang. Once the device
is hung, the bnx2 driver will not be able to reset the device.
We believe that it is legal to read beyond the end tag and
therefore the solution is to limit the read/write length.
A majority of this patch is from Matthew Wilcox who gave code for
reworking the PCI vpd size information. A PCI quirk added for the
Broadcom NIC's to limit the read/write's.
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Some PCI devices will lock up if we attempt to read from VPD addresses
beyond some device-dependent limit. Until we can identify these
devices and adjust the file size accordingly, only let root read VPD
through sysfs to prevent a DoS by normal users.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch is the minimal amount of code needed to support
wake-on-lan in platform mode properly (i.e. "ethtool -s eth0 wol g"
is sufficient, no additional magic needed) for me.
This is derived from David Brownells patch
(http://lists.laptop.org/pipermail/devel/2007-April/004691.html).
However I decided to move the hook into pci-acpi.c since the other
two pci hooks also live there and pci and acpi are the only users of
the platform_enable_wakeup-hook.
As a 'side-effect' this also makes wake on usb activity work for me
and I had to disable usb wakeup (which is enabled by default) using
the power/wakeup sysfs functionality ("echo disabled >
${sysfs_path_to_device}/power/wakeup").
(BTW I first thought the 'immediate reboot because of usb wake' effect is
caused by the optical mouse generating a wake event, but it rather
seems to be a problem with a flaky secondary usb host controller,
which sees a connected device where nothing is attached)
Signed-off-by: Tobias Diedrich <ranma+kernel@tdiedrich.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Make pci_setup_device() write the bus ID directly into the allotted storage,
rather than using pci_name() as the address as that now returns a const
pointer.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Current pciehp driver saves its private data pointer into pci_dev
structure using pci_set_drvdata()/pci_get_drvdata(). But because
pciehp is not a pci device driver but a PCI Express service driver, it
should save its private data pointer into pcie_device structure using
set_service_data()/get_service_data().
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Currently, pciehp driver enables command completed interrupt as follows.
(1) Don't enable at initialization.
(2) Enable command completed interrupt whenever pciehp issues a
command, if the command doesn't attempt to disable the interrupt.
(3) Disable command completed interrupt at driver unloading.
Once we enable command completed interrupt, we don't need to re-enable
it for every command. So we can simplify above steps as follows:
(1) Enable command completed interrupt at initialization.
(2) No special sequence for command completed interrupt.
(3) Disable command completed interrupt at driver unloading.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Current pciehp driver's intialization sequence is as follows:
(1) initialize controller data structure
(2) install interrupt handler
(3) enable software notification
(4) initialize controller specific slot data structure
(5) initialize generic slot data structure and register it to pci hotplug core
The interrupt handler of pciehp assumes that controller specific slot
data structure is already initialized. However, it is installed at (2)
before initializing controller specific slot data structure at
(4). Because of this, pciehp driver cannot handle the following cases
properly.
- If devices that shares IRQ with pciehp raise interrupts between (2) and (4).
- If hotplug events (e.g. MRL open) happen between (3) and (4).
We already have a workaround for this problem ("pciehp: fix NULL
dereference in interrupt handler: dbd79aed1a).
But we still need fundamental fix.
This patch fix the problem by changing the initilization sequence as follows:
(1) initialize controller data structure
(2) initialize controller specific slot data structure
(3) install interrupt handler
(4) enable software notification
(5) initialize generic slot data structure and register it to pci hotplug core
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Convert printks to use dev_printk().
I converted pr_debug() to dev_dbg(). Both use KERN_DEBUG and are enabled
only when DEBUG is defined.
I converted printk(KERN_DEBUG) to dev_printk(KERN_DEBUG), not to dev_dbg(),
because dev_dbg() is only enabled when DEBUG is defined.
I converted DBG(KERN_INFO) (only in setup-bus.c) to dev_info(). The DBG()
name makes it sound like debug, but it's been enabled forever, so dev_info()
preserves the previous behavior.
I tried to make the resource assignment formats more consistent, e.g.,
"BAR %d: got res [%#llx-%#llx] bus [%#llx-%#llx] flags %#lx\n"
instead of sometimes using "start-end" and sometimes using "size@start".
I'm not attached to one or the other; I'd just like them consistent.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The pcie_poll_cmd() and pcie_wait_cmd() are too large to be
inlined.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Change command polling frequency to 100Hz from 10Hz in order to reduce
the delay in the common case of a command completing quickly.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cleanup pcie_poll_cmd(): check the slot status once before entering our
completion test loop and convert the loop to a simpler while() block.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
For the ranges with IORESOURCE_PREFETCH, export a new resource_wc interface in
pci /sysfs along with resource (which is uncached).
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Since the second argument of acpi_pci_choose_state() and
platform_pci_choose_state() is never used, remove it.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
Get rid of a superfluous acpi_pm_device_sleep_state() parameter. The
only legitimate value of that parameter must be derived from the first
parameter, which is what all the callers already do. (However, this
does not address the fact that ACPI still doesn't set up those flags.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Detect all physical PCI slots as described by ACPI, and create entries in
/sys/bus/pci/slots/.
Not all physical slots are hotpluggable, and the acpiphp module does not
detect them. Now we know the physical PCI geography of our system, without
caring about hotplug.
[kaneshige.kenji@jp.fujitsu.com: export-kobject_rename-for-pci_hotplug_core]
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Acked-by: Greg KH <greg@kroah.com>
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: fix build with CONFIG_DMI=n]
Signed-off-by: Alex Chiang <achiang@hp.com>
Cc: Greg KH <greg@kroah.com>
Cc: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Cc: Len Brown <lenb@kernel.org>
Acked-by: Len Brown <len.brown@intel.com>
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Suresh Siddha