Since the standards only define 12 legacy rates, 32 is certainly
a sane upper limit and we don't need to use u64 everywhere. Add
sanity checking that no more than 32 rates are registered and
change the variables to u32 throughout.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On Friday 16 January 2009 20:33:43 Kalle Valo wrote:
> N800 and N810 support is not on mainline yet, for stlc45xx I decided
> to add module parameters for the gpio numbers. Here's the commit from
> stlc45xx repo:
>
> 35afc5df00
This is the same patch for p54spi.
It removes all N800/N810 specific code from p54spi, so the driver can be used on
other architectures, or configurations as well.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A recent change in the usb core "USB: change interface to usb_lock_device_for_reset()"
conflicts with "p54usb: utilize usb_reset_device for 3887".
Sadly, we have to call usb_reset_device before we can upload the firmware on 3887.
Unless someone figures out how to reliably stop the 3887 so the hardware is still usable
next time we want to start it.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Usually every prism54 design hardware has a tiny eeprom chip in which all
device specific data for calibration and link-tuning is stored.
The stlc45xx chips are the only exception.
They are made for embedded devices, where space is scarce.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for longbow RF chip.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support to upload pre-calculated calibration data to the firmware.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 reserves 24 bytes in skb->cb for the driver.
So far, we only used them to keep track of used and free device memory.
But p54spi will need a slice of it, as well as the stuck frame detection.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Old firmwares had no problems processing frames which filled eighth of the memory window.
However we have to be a bit more careful with fat frames when we talk to new firmwares.
Apart from that, I confess the old logic was a bit weird and not very sophisticated.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch addresses all recent comments from Johannes Berg:
1st: (reference http://marc.info/?l=linux-wireless&m=123124685019631 )
>First off: all those should return NETDEV_TX_OK/BUSY.
>iwl-agn: returns 0 (== NETDEV_TX_OK, but still should be changed)
>[...]
>p54: same (some paths)
2nd:
> due to your PS patch ("p54: power save management"), please run sparse:
> make C=2 CF=-D__CHECK_ENDIAN__ M=...
> +drivers/net/wireless/p54/p54common.c:1753:8: warning: incorrect type in assignment (different base types)
> +drivers/net/wireless/p54/p54common.c:1769:29: warning: incorrect type in assignment (different base types)
The cpu_to_le16 ended up in the wrong line... Sorry!
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch implements dynamic power save feature for p54.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
According to STMicroelectronics' LMAC documentation, the P54_FILTER_TYPE_TRANSPARENT flag
"configures the receive frame filter to pass all frames without regard to type and address matching."
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Respect all documented bits in the eeprom about the device diversity features.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The set_key callback now seems rather odd, passing a MAC address
instead of a station struct, and a local address instead of a
vif struct. Change that.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Bob Copeland <me@bobcopeland.com> [ath5k]
Acked-by: Ivo van Doorn <ivdoorn@gmail.com> [rt2x00]
Acked-by: Christian Lamparter <chunkeey@web.de> [p54]
Tested-by: Kalle Valo <kalle.valo@nokia.com> [iwl3945]
Tested-by: Samuel Ortiz <samuel@sortiz.org> [iwl3945]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds a sub-routine that parses the default country eeprom entry
and forwards the obtained Alpha2 identifier to the regulatory sub-system.
Note: I dropped the p54 specific regdomain<->alpha2 conversion code for now.
But it will be added as soon as there's the common library function is ready.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch will prevent anyone to upload a firmware which was not designed for his device.
There's still a catch:
There is no easy way to detect if a firmware is for PCI or for USB (1st Gen),
because they all share the same LM86 identifier.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes on unload or reboot the 3887 USB devices become stuck.
<usual log entry>
kernel: usbcore: registered new interface driver p54usb
kernel: usb 2-10: (p54usb) reset failed! (-110)
kernel: p54usb: probe of 2-10:1.0 failed with error -110
[...]
and a physical unplug and replug was necessary.
However we should be able to do this in software as well,
without any user interaction.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch enables frame injection in monitor mode for all p54 devices.
As a result, any user can finally use the aircrack-ng suite out of the box.
e.g:
aireplay-ng --test wlan0
Trying broadcast probe requests...
Injection is working!
Found 1 AP
Trying directed probe requests...
XX:XX:XX:XX:XX:XX - channel: i - 'SSID'
Ping (min/avg/max): 1.536ms/3.193ms/4.377ms Power: 193.00
30/30: 100%
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch introduce new shiny named labels for our 8 (4 - on old firmware) queues.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Artur Skawina confirmed that the first generation devices needs the same
URB_ZERO_PACKET flag, in oder to finish the pending transfer properly.
The second generation has been successfully fixed by
"p54usb: fix random traffic stalls (LM87)" (43af18f06d5)
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In theory, the firmware acks the received a data frame, before signaling the driver to free it again.
However Artur Skawina <art.08.09@gmail.com> has shown that it can happen in reverse order as well.
This is very bad and could lead to memory corruptions, oopses and panics.
Thanks to Artur Skawina <art.08.09@gmail.com> for reporting and debugging this issue.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Tested-by: Artur Skawina <art.08.09@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If we let the firmware do the data encryption, we have to remove the ICV and
(M)MIC at the end of the frame before we can give it back to mac80211.
Or, these data frames have a few trailing bytes on cooked monitor interfaces.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a obvious memory leak in the eeprom parser.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
p54 doesn't support AES-128-CMAC offload.
This patch will fix the noisy mac80211 warnings, when 802.11w is enabled:
mac80211-phy189: failed to set key (4, ff:ff:ff:ff:ff:ff) to hardware (-22)
mac80211-phy189: failed to set key (5, ff:ff:ff:ff:ff:ff) to hardware (-22)
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bug that could occur, if it the eeprom is incomplete or partly corrupted.
BUG: unable to handle kernel NULL pointer dereference at 00000008
IP: p54_assign_address+0x108/0x15d [p54common]
Oops: 0002 [#1] SMP
Pid: 12988, comm: phy1 Tainted: P W 2.6.28-rc6-wl #3
RIP: 0010: p54_assign_address+0x108/0x15d [p54common]
[...]
Call Trace:
p54_alloc_skb+0xa3/0xc0 [p54common]
p54_scan+0x37/0x204 [p54common]
[...]
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/p54/p54common.c: In function ‘p54_config’:
drivers/net/wireless/p54/p54common.c:1853: warning: ‘ret’ may be used uninitialized in this function
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch hopefully fixes a mac80211<->p54 interaction problem, which was
described by Larry Finger (ref: http://marc.info/?l=linux-wireless&m=123009889327707 )
I guess the warning was triggered by pending frames in the receive queue,
while we're doing a band change 5GHz.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All LM87 firmwares need a explicit termination "packet",
in oder to finish the pending transfer properly.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes two small flaws:
- restore the original TKIP IV if we altered it.
- reserve & initialize ICV with zeros.
This is actually only necessary for some obsolete p54usb firmwares.
But we don't know yet, if all devices are compatible with the new revisions.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the USB ID for Thomson Speedtouch 121g to p54usb.
Signed-off-by: Michiel <michiel@ettema.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On x86_64 architecture with 4K page size and SLUB debugging enabled, stress
testing on p54usb has resulted in skb allocation failures of O(1) and extreme
page fragmentation. Reducing rx_mtu fixes this problem by reducing the size of
all receive skb allocations to be of O(0). This change does not impact
performance in any way.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a serious regression (introduced by:
"p54: fix memory management")
that affected isl3886+net2280 usb devices operation.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Tested-by: Artur Skawina <art.08.09@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch simplifies the tx code a bit and will be necessary for
the upcoming stlc45xx<->p54 port.
In detail: we no longer have to tell all back-end drivers directly,
if we want to free a frame right after it was send to the firmware,
or if we do it in the library callback later.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch replaces the static rssi auto calibration data
with more precise values out of the device's eeprom.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves a good chunk of code from the former statistic update
timer routine into a workqueue, which is kindly provided by mac80211.
Also as a nice side-effect we can lay the foundation for other
essential housekeeping features we want to do in the future.
e.g:
- drain the (clogged) tx_queue.
- initiate bursts.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes an oops when the devices suddenly starts
to receive martian data frames.
bug reference:
http://marc.info/?l=linux-wireless&m=122872280317635&w=2
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch fixes an old FIXME in p54pci.c by moving the "queue full"
check into the common library, where we can deal with it properly.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch replaces the newly introduced sta_notify_ps function,
which can be used to notify the driver about every power state
transition for all associated stations, by integrating its functionality
back into the original sta_notify callback.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Alan Stern found several flaws in p54usb's implementation and annotated:
"usb_kill_urb() and similar routines do not expect an URB's completion
routine to deallocate it. This is almost obvious -- if the URB is deallocated
before the completion routine returns then there's no way for usb_kill_urb
to detect when the URB actually is complete."
This patch addresses all known limitations in the old implementation and fixes
khub's "use-after-freed" hang, when SLUB debug's poisoning option is enabled.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Cc: stable@kernel.org
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes the checksum calculation for lm87 firmwares
on big endian platforms, the device treats the data as
an array of 32-bit little endian values so the driver
needs to do that as well.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch replaces the static "p54:" strings in front of most printk's
with their corresponding per-device names.
It was always a bit of a hassle to check which device was
generating all the messages.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Thanks to the introduction of "changed" flags, we no longer
have to do the bookkeeping of p54's firmware state for everything.
Thus we can cut down redundancy code.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Those firmwares are probably capable of reprogramming the device's eeprom.
We better support them officially, before all the accidents happen.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch allows p54 to utilize its WEP, TKIP and CCMP accelerator.
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch addresses the problem in:
http://marc.info/?l=linux-wireless&m=122727674810057&w=2
Thanks to Stefan Steuerwald <salsasepp@googlemail.com>
extensive iPod touch tests. We could finally squash some bugs in
p54's master mode / access point implementation.
Let's hope we got everything right this time and all stations
from now on will wake up on TIM and receive their queued frames
and go to sleep again without any hiccups.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a regression (introduced by
"p54: more definitions form lmac_longbow.h and pda.h")
It turned out that the "ret" variable wasn't initialized and
this caused the following warnings/errors to appear:
wmaster1: failed to set TX queue parameters for queue 2
wmaster1: failed to set TX queue parameters for queue 3
wmaster1: failed to set TX queue parameters for queue 1
wmaster1: failed to set TX queue parameters for queue 0
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As was pointed out in "p54: honour bss_info_changed's short slot time settings",
bss_info_changed provides more useful settings that can be used by the driver.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes pointed out that the driver has cache the firmware for
suspend/resume cycles.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg