On the Xonar DX, initialize all bits of the two-wire control register.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a mixer control for switching whatever it is that is connected to
GPIO pin 1 on the Xonar DX.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If the card model does not have a digital input or an AC97 codec,
disable the respective interrupt and mixer controls.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When selecting the capture source on the Xonar DX, the input jack must
be routed to either the line input or the microphone input by setting a
GPIO pin. This requires an additional callback so that the model driver
can hook into the toggling of AC97 switches.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Change the card short name to show to show the card name instead of the
chip name.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When playing data at 96 kHz or higher, reduce the DAC oversampling rate
to 32.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move the code that is common to all Xonar models to a separate function,
and make it more generic in preparation for another model.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Rename all CS5381 symbols to CS53x1 because they can also be used for
Xonar models with a CS5361.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use separate model structures for the D2 and D2X so that the init
function does not have to check for the model again.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
"GPL 2" does not mean that there have to be two MODULE_LICENSE("GPL")
entries. ;-)
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On C-Media cards, the GPIO pin 0 of the CM9780 must be handled exactly
like on Xonar cards, so move the Xonar code to the common mixer code.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add support for mic automute in clevo-m720r ALC883 model, and rename it
to more generic clevo-m720. Also change model entry in ALSA-Configuration.txt
accordingly.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Forgot one more: 3stack-hp model also have now the same mixer as
3stack-6ch (after DAC assignment fix in ALC883), so use it avoiding
duplicating the same mixer definition.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
After DAC assignment fix in ALC883, alc888_6st_dell_mixer is now the
same as alc883_base_mixer. Avoid duplicated code and use
alc883_base_mixer in 6stack-dell model, removing alc888_6st_dell_mixer
definition.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
After DAC assignment fix in ALC883, the 6stack-hp model is now the same
as 6stack-dig. So just remove 6stack-hp model and replace its use with
6stack-dig.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* moving most of clock-specific code to card-specific routines
* support for ESI Juli
* to-be-researched - monitoring of analog/digital inputs
Signed-off-by: Pavel Hofman <dustin@seznam.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
sparc64:
sound/pci/pcxhr/pcxhr.c: In function `pcxhr_update_r_buffer':
sound/pci/pcxhr/pcxhr.c:459: warning: cast to pointer from integer of different size
sound/pci/pcxhr/pcxhr.c: In function `pcxhr_trigger_tasklet':
sound/pci/pcxhr/pcxhr.c:628: warning: long int format, different type arg (arg 4)
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
sound/pci/pcxhr/pcxhr_core.c: In function `pcxhr_set_pipe_state':
sound/pci/pcxhr/pcxhr_core.c:899: warning: long int format, different type arg (arg 4)
suseconds_t is int on sparc64.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
sparc32:
sound/pci/aw2/aw2-alsa.c: In function 'snd_aw2_create':
sound/pci/aw2/aw2-alsa.c:282: error: 'DMA_32BIT_MASK' undeclared (first use in this function)
sound/pci/aw2/aw2-alsa.c:282: error: (Each undeclared identifier is reported only once
sound/pci/aw2/aw2-alsa.c:282: error: for each function it appears in.)
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Disable the master clock outputs of any unused I2S inputs.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Put the flag that enables the MIDI port into the model structure instead
of passing it as a separate parameter to oxygen_pci_probe().
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Allow the model drivers to specify if the codec communication goes over
SPI or a 2-wire bus.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When specifying which PCM devices to use, model drivers now use flags
that also specify the routing between PCM devices and DMA channels
instead of just DMA channel bits. This simplifies some code that checks
for these flags.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add controls to enable monitoring of the analog and digital inputs.
To allow monitoring after loading the driver when nothing has been
played back or recorded yet, the I2S input and outputs are initialized
to a valid configuration.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move the PCM1796 register symbol definitions to their own header file.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move the WM8786 register symbol definitions to their own header file.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Keep the format verb at closing PCM streams.
Introduced snd_hda_codec_cleanup_stream() for the parcicular purpose.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Actually clfe and surround DACs are inverted in alc883_dac_nids array
(see ALC883 datasheet). I discovered this while testing multi-channel
setup (using 3stack-6ch-dig model) on MSI 945GCM5 V2 motherboard that
has an ALC883 codec. Simply Rear Left/Right and Center/LFE were swapped
in 6 channel mode (also in 4 channel mode you didn't get rear left/right
output). Other models also were affected by this bug, as can be seen by
the mixer layouts that "workaround" this (the real bug was not noticed,
and some other models simply played with mixer and initial verbs). Thus
along with fixing the order of dac nids, also change the models that
relied on previous dac ordering properly.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The variable is_capture is initialized but never used otherwise.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
type T;
identifier i;
constant C;
@@
(
extern T i;
|
- T i;
<+... when != i
- i = C;
...+>
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* removing the hack with NON_AKM ak4xxx type
* support for card-specific flags in ak4114_stats
* definition of the flags for corresponding cards
Signed-off-by: Pavel Hofman <dustin@seznam.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AK4114 on Juli@ has the SPDIF input sample rate detection and
causes errors when an incompatible sample rate is chosen.
The patch adds the open hook to check the current rate and limit
the hw constraints.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The docking station headphone output had no audio and jack sense
was not considered.
Jack information from the laptop itself and the dock are combined, as
the dock does not obscure the connector.
Signed-off-by: Tony Vroon <tony@linx.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The hda-intel driver has a problem at power-off on ASUS P5AD2.
It's caused when the position-buffer is enabled -- most likely a
hardware-specific problem.
This patch adds a quirk to avoid the unnecessary enablement of
position-buffer.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Map 3stack-6ch-dig ALC662 model for Asus P5GC-MX.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently ALC662 doesn't suport amp mute for AmpOut in nids 0x02, 0x03,
0x04 (see block diagram in ALC662 datasheet page 3, does M correspond to
mute?). The result is that currently mute for "Front Playback Switch",
"Surround Playback Switch", "Center Playback Switch" and "LFE Playback
Switch" mixer items doesn't work (tested on Asus P5GC-MX motherboard
with 3stack-6ch model).
The solution I found for this is to mute the proper inputs in 0x0c,
0x0d, 0x0e audio mixers.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently, the headphone controls are created as Master wrongly in
some cases, and this prevents the virtual master controls.
The patch fixes the problem by simply using "Headphone" always for
headphone controls.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fixed issue on some laptops that if the Master mixer and DAC mixers are
turned all the way up that will cause distortion. This is fixed by limiting
the max volume with the volume knob nid.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Clemens Ladisch