Currently the io_apic.c has several parallel arrays for different
kinds of data that can be know about an irq. The parallel arrays
make the code harder to maintain and make it difficult to remove
the static limits on the number of the number of irqs.
This patch pushes irq_data and irq_vector into a irq_cfg array and
updates the code to use it.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
NR_IRQ_VECTORS is currently a compatiblity define set to NR_IRQs.
This patch updates the users of NR_IRQ_VECTORS to use NR_IRQs instead
so that NR_IRQ_VECTORS can be removed.
There is still shared code with arch/i386 that uses NR_IRQ_VECTORS
so we can't remove the #define just yet :(
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If we have an irq that comes from multiple io_apic pins the FINAL action
(which is io_apic_sync or nothing) needs to be called for every entry or
else if the two pins come from different io_apics we may not wait until
after the action happens on the io_apic.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For some reason the code has been picking TARGET_CPUS when asked to
set the affinity to an empty set of cpus. That is just silly it's
extra work. Instead if there are no cpus to set the affinity to we
should just give up immediately. That is simpler and a little more
intuitive.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently we have two routines that do practically the same thing
setup_IO_APIC_irq and io_apic_set_pci_routing. This patch makes
setup_IO_APIC_irq the common factor of these two previous routines.
For setup_IO_APIC_irq all that was needed was to pass the trigger
and polarity to make the code a proper subset of io_apic_set_pci_routing.
Hopefully consolidating these two routines will improve maintenance
there were several differences that simply appear to be one routine
or the other getting it wrong.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch replaces all instances of "set_native_irq_info(irq, mask)"
with "irq_desc[irq].affinity = mask". The latter form is clearer
uses fewer abstractions, and makes access to this field uniform
accross different architectures.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
By precomputing old_mask I remove an extra if statement, remove an
indentation level and make the code slightly easier to read.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit 2ff2d3d747.
Uwe Bugla reports that he cannot mount a floppy drive any more, and Jiri
Slaby bisected it down to this commit.
Benjamin LaHaise also points out that this is a big hot-path, and that
interrupt delivery while idle is very common and should not go through
all these expensive gyrations.
Fix up conflicts in arch/i386/kernel/apic.c and arch/i386/kernel/irq.c
due to other unrelated irq changes.
Cc: Stephane Eranian <eranian@hpl.hp.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Andrew Morton <akpm@osdl.org>
Cc: Uwe Bugla <uwe.bugla@gmx.de>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
IRQ mask bits assumed a 60xx or newer generation chip, which is very
wrong for the 50xx series. Luckily both generations shared the per-port
interrupt mask bits, leaving only the "misc chip features" bits to be
completely mismatched.
Fix 50xx by ensuring we only program bits that exist.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The code in mv_edma_cfg() reflected its 60xx origins, by doing things
[slightly] incorrectly on the older 50xx and newer 6042/7042 chips.
Clean up the EDMA configuration setup such that, each chip family
carefully initializes its own EDMA setup.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Manuel Lass reports:
> This bug is also present in 2.6.21-rc1, and this patch
> indeed fixes it.
The change to the devres layer re-orders the execution of cleanup
functions and in turn causes the pcmcia layer to oops as it zaps a
pointer now needed later on. We simply leave the pointer alone.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Also export dev_disable as this is needed by drivers doing slave decode
filtering, which will follow shortly
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Each place in pdc_ata_init_one() that initialises a SATA
port first calls pdc_ata_setup_port(), and then manually
assigns the port's ->scr_addr. Simplify the code by extending
pdc_ata_setup_port() to also handle scr_addr initialisation;
for PATA ports we pass NULL as scr_addr.
The initialisation of the PATA-only 20619 redundantly set
up scr_addr for the ports. Remove this.
Tested on 20619, 20575, and 20775 chips.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When I merged my 20619 new EH conversion with #libata-upstream
I had to manually resolve a conflict, and inadvertently lost
pdc_pata_ops' ->post_internal_cmd binding. Corrected by this patch.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This is a follow up for f80dff9da0 which
didn't include adaption for the new ns9xxx machine support.
Signed-off-by: Uwe Kleine-König <ukleinek@informatik.uni-freiburg.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Noticed while building a s3c2410 kernel :
drivers/mtd/nand/s3c2410.c: In function 's3c2440_nand_calculate_ecc':
drivers/mtd/nand/s3c2410.c:476: warning: format '%06x' expects type 'unsigned int', but argument 3 has type 'long unsigned int'
This patch fixes it.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
aware
Since TEXT_OFFSET is meant to determine RAM location for kernel use,
itshould affect .data and .bss initial mapping in the XIP case.
Otherwise a XIP kernel would crash if TEXT_OFFSET gets somewhat larger
than 2MB.
Corresponding code is also moved up a bit to be near the similar .text
mapping code making the whole a bit more straight forward to understand.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since commit 2552fc27ff XIP kernels failed
to boot because (_end - PAGE_OFFSET - 1) is much smaller than the size
of the kernel text and data in the XIP case, causing the kernel not to
be entirely mapped.
Even in the non-XIP case, the use of (_end - PAGE_OFFSET - 1) is wrong
because it produces a too large value if TEXT_OFFSET is larger than 1MB.
Finally the original code was performing one loop too many.
Let's break the loop when the section pointer has passed the last byte
of the kernel instead.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
All drivers must implement this hook, otherwise ATA commands would go
nowhere (and a lot of other oopsen would appear as well).
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Separate sata_vsc interrupt handling into a normal (per-port) path and an
error path with the addition of vsc_port_intr and vsc_error_intr
respectively. The error path handles interrupt based
hotplug events which requires the definition of vsc_freeze and vsc_thaw.
Note: vsc_port_intr has a workaround for unexpected interrupts that occur
during polled commands. This fixes a regression between 2.6.19 and 2.6.20.
Changes in take2:
* removed definition of invalid fis bit
* let standard ata-error-handling handle the serror register
* clear all unhandled interrupts
* revert changes to vsc_intr_mask_update (vsc_thaw enables all interrupts)
* use unlikely() for the pci-abort and not-our-interrupt cases in vsc_sata_interrupt
Changes in take3:
* Unify the "add" + "hook-up" patches into this single patch
[htejun@gmail.com: clean up comments and suggestions]
Cc: Jeremy Higdon <jeremy@sgi.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
sata_sil used to trigger HSM error if IRQ occurs during polling
command. This didn't matter because polling wasn't used in sata_sil.
However, as of 2.6.20, all IDENTIFYs are performed by polling and
device detection sometimes fails due to spurious IRQ. This patch
makes sata_sil ignore and clear spurious IRQ while executing commands
by polling.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
intx should be turned on when pci_enable_msi() fails not when it
succeeds. Fix it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
80c test mask is at bits 18 and 19 of EIDE Controller Configuration
not 22 and 23. Fix it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch (as861) adds sysfs attributes to expose the autosuspend
delay value for each USB device. If the user changes the delay from 0
(no autosuspend) to a positive value, an autosuspend is attempted.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as860) adds two new sysfs routines:
sysfs_add_file_to_group() and sysfs_remove_file_from_group().
A later patch adds code that uses the new routines.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Maneesh Soni <maneesh@in.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as859) makes the default USB autosuspend delay a module
parameter of usbcore. By setting the delay value at boot time, users
will be able to prevent the system from autosuspending devices which
for some reason can't handle it.
The patch also stores the autosuspend delay as a per-device value. A
later patch will allow the user to change the value, tailoring the
delay for each individual device. A delay value of 0 will prevent
autosuspend.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as858) makes some minor cleanups to sysfs.c in usbcore.
Unnecessary tests are removed and a few temp variables are added.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds a blacklist to the USB core to handle some autosuspend and
string issues that devices have.
Originally written by Oliver, but hacked up a lot by Greg.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I don't think the current code works with multiple iovecs.
The original would just copy the first part of priv->buf
over and over into multiple iovecs.
Signed-off-by: Sarah Bailey <saharabeara@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The below patch proposes to use USB defines (defined in linux/hid.h)
instead of just plain numbers in the USB_INTERFACE_INFO statements.
Signed-off-by: Michael Opdenacker <michael@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add argumentation in defense of using __attribute__((packed)) in USB
descriptors authored by Dave Brownell. Necessary as in some cases it
seems superfluous.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I would like to add the VID and PID for Telldus Technologies Homeautomation
usb-dongle to the ftdi_sio driver.
From: Micke Prag <micke.prag@telldus.se>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as856) attempts to improve the performance of uhci-hcd by
removing the asynchronous skeleton Queue Headers. They don't contain
any useful information but the controller has to read through them at
least once every millisecond, incurring a non-zero DMA overhead.
Now all the asynchronous queues are combined, along with the period-1
interrupt queue, into a single list with a single skeleton QH. The
start of the low-speed control, full-speed control, and bulk sublists
is determined by linear search. Since there should rarely be more
than a couple of QHs in the list, the searches should incur a much
smaller total load than keeping the skeleton QHs.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as855) adds some convenience macros to uhci-hcd, to help
simplify the code for computing hardware DMA pointers.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds a driver for the Davicom DM9601 USB 1.1 10/100Mbps
ethernet adaptor using the usbnet framework.
See http://www.davicom.com.tw/eng/products/dm9601.htm for details.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add device IDs for the JVC-PRX1 port replicator. Additionally cleans up
the tabs on a few of other IDs in the list.
Reported by: Reuben Thomas <rrt@sc3d.org>
Signed-off-by: David Hollis <dhollis@davehollis.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
mon_bin_exit() and mon_text_exit() are called from __init code, so don't mark
them as __exit.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ioctl is commented out for now, until we verify some userspace
application issues.
Cc: Christian Lucht <lucht@codemercs.com>
Cc: Robert Marquardt <marquardt@codemercs.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds all of the known Option device ids to the driver.
Many thanks to some Option engineers for getting me this list.
Cc: Matthias Urlichs <smurf@smurf.noris.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is no need to have two tables with the same device ids in it.
Cc: Matthias Urlichs <smurf@smurf.noris.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts commit c353c3fb07.
It turns out that we end up with a loop trying to load the unix
module and calling netfilter to do that. Will redo the patch
later to not have this loop.
Acked-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a device fails to register the class symlinks where not cleaned up.
This left a symlink in the /sys/class/"device"/ directory that pointed
to no where. This caused the sysfs_follow_link Oops I reported earlier.
This patch cleanups up the symlink. Please apply. Thank you.
Signed-Off: James Simmons <jsimmons@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch makes the needlessly global struct kmod_mk static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Eric W. Biederman