wm831x_gpio_direction_output() ignored the state passed into it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch adds cell->disable() calls to the tmio-mmc
probe() error handling and the remove() function.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Remove const from the tmio-mmc platform data hclk V3.
This change makes it possible to remove the type cast
from the sh_mobile_sdhi driver which is using the clock
framework to get the clock rate.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch changes the tmio_mmc driver to wait 100ms
before checking the card detect status. This type of
delay is quite common among mmc drivers, it seems that
most hardware platforms need to give the hardware some
time to settle before checking card availabilty.
Hotplug is half-broken without this patch on the sh7724
Ecovec board. Hot insertion seems ok but eject is never
detected without this patch.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Enable MMC_CAP_XX support in the tmio_mmc driver if
pdata->capabilities is set.
Signed-off-by: Yusuke Goda <goda.yusuke@renesas.com>
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
On SuperH platforms the SDHI controller does not produce any command IRQs after
a completed IO. This leads to card-detect interrupts staying disabled. Do not
disable card-detect interrupts on DATA IRQs.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add base address for generic slave ID0, ID1, ID2
and introduced one more entry to align RTC module number between
twl4030 and twl6030
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch disables TWL4030/5030 I2C1 adn I2C4(SR) internal pull-up, to
use only the external HW resistor >=470 Ohm for the assured
functionality in HS mode.
While testing the I2C in High Speed mode, it was discovered that
without a proper pull-up resistor, there is data corruption during
multi-byte transfer. RTC(time_set) test case was used for testing.
From the analysis done, it was concluded that ideally we need a
pull-up of 1.6k Ohm(recomended) or atleast 470 Ohm or greater for
assured performance in HS mode.
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Allen Pais <allen.pais@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Intel Poulsbo (SCH) chipset LPC bridge controller contains several
functions. Creating and MFD driver for the LPC bridge controller allows
simultaneous use of SMBus and GPIO interfaces on the SCH.
Signed-off-by: Denis Turischev <denis@compulab.co.il>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
For ACPI based systems, we should check for ACPI conflicts when adding the
platform devices. The test will always succeed for non ACPI platforms.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Change the typo CONFIG_INPUT_TWL4030_PWBUTTON_MODULE in the
twl_has_pwrbutton definition to CONFIG_INPUT_TWL4030_PWRBUTTON_MODULE.
Signed-off-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Signed-off-by: Christoph Egger <siccegge@stud.informatik.uni-erlangen.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Use genirq to simplify IRQ handling in 88pm860x. Remove the interface of
mask/free IRQs on 88pm860x. All these work is taken by genirq. Update the
touchscreen driver of 88pm860x since IRQ handling is changed.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch fixes wrong goto statement for error handling on probe.
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Use i2c_dummy in 88pm860x driver to avoid using static in probe function.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
MAX8925 is a PMIC that contains charger component
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
MAX8925 is a PMIC that contains RTC component.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Update thread irq handler. Simply the interface of using thread irq.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Update I2C driver in order to fit all of three I2C components in max8925.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Variable remap was incorrectly referencing remap_off for the remap_sleep
case when configuring TWL4030 power scripts.
Signed-off-by: Mike Turquette <mturquette@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The WM8994 is a highly integrated ultra low power audio hub CODEC.
Since it includes on-board regulators and GPIOs it is represented
as a multi-function device, though the overwhelming majority of
the functionality is provided by the ASoC CODEC driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
As a separate patch due to the large size.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
htc-i2cpld should depend on GPIOLIB, otherwise there are many
build errors:
drivers/mfd/htc-i2cpld.c:50: error: field 'chip_out' has incomplete type
drivers/mfd/htc-i2cpld.c:54: error: field 'chip_in' has incomplete type
drivers/mfd/htc-i2cpld.c:243: warning: type defaults to 'int' in declaration of '__mptr'
drivers/mfd/htc-i2cpld.c:243: warning: initialization from incompatible pointer type
drivers/mfd/htc-i2cpld.c:278: warning: type defaults to 'int' in declaration of '__mptr'
drivers/mfd/htc-i2cpld.c:278: warning: initialization from incompatible pointer type
drivers/mfd/htc-i2cpld.c:282: warning: type defaults to 'int' in declaration of '__mptr'
drivers/mfd/htc-i2cpld.c:282: warning: initialization from incompatible pointer type
drivers/mfd/htc-i2cpld.c:315: error: dereferencing pointer to incomplete type
drivers/mfd/htc-i2cpld.c:322: warning: type defaults to 'int' in declaration of '__mptr'
drivers/mfd/htc-i2cpld.c:322: warning: initialization from incompatible pointer type
drivers/mfd/htc-i2cpld.c:467+: error: dereferencing pointer to incomplete type [19X]
drivers/mfd/htc-i2cpld.c:490: error: implicit declaration of function 'gpiochip_add'
drivers/mfd/htc-i2cpld.c:504: error: implicit declaration of function 'gpiochip_remove'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The TWL4030_BCI_BATTERY config option originates from a patch to the
omap git tree. However inclusion in linux was seemingly rejected and
the functionality nears inclusion under a different name so this
removes the bits of the old version that made it into the mainline
kernel again.
Signed-off-by: Christoph Egger <siccegge@stud.informatik.uni-erlangen.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This fixes the aged and unreachable debugfs code in the AB3100
OTP driver so that it's (A) reachable and (B) works. Bug detected
in parallell by Christoph Egger using VAMOS and Robert P. J. Day
by his kernel scanning script.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Cc: Christoph Egger <siccegge@stud.informatik.uni-erlangen.de>
Cc: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This reintroduces the entropy sampling of the AB3100 IRQ as the
IRQF_SAMPLE_RANDOM is going out according to the feature removal
schedule. I'm trying to do this the right way then, so CC:ing some
random people for a quick review. We add entropy for interrupt
events in the AB3100 which are truly random in nature, like
external cables being connected, voltages on batteries dropping
below certain ranges, ADC triggers or overheating.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Cc: Robin Getz <rgetz@blackfin.uclinux.org>
Acked-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This change introduces a driver for the HTC PLD chip found
on some smartphones, such as the HTC Wizard and HTC Herald.
It works through the I2C bus and acts as a GPIO extender.
Specifically:
* it can have several sub-devices, each with its own I2C
address
* Each sub-device provides 8 output and 8 input pins
* The chip attaches to one GPIO to signal when any of the
input GPIOs change -- at which point all chips must be
scanned for changes
This driver implements the GPIOs throught the kernel's
GPIO and IRQ framework. This allows any GPIO-servicing
drivers to operate on htcpld pins, such as the gpio-keys
and gpio-leds drivers.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
MAX8925 contains 3 Buck and 20 LDO regulator.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add subdevs in MAX8925. MAX8925 includes regulator, backlight and touch
components.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Basic Max8925 support, which is a power management IC from Maxim
Semiconductor.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Remove the support 88PM8607 A0/A1 stepping. There's some register
definition changes in B0 stepping. It can make software more efficient.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Enable touchscreen driver for the 88pm860x multi function core.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Enable led sub device in Marvell 88PM860x. Two LED arrays can be supported.
Each LED array can be used for R,G,B leds.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
At most, three backlight device can be supported in 88pm860x driver.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
88PM860x is a complex PMIC device. It contains touch, charger, sound, rtc,
backlight, led, and so on.
Host communicates to 88PM860x by I2C bus. Use thread irq to support this
usage case.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Rename 88PM8607 to 88PM860X in both Makefile and Kconfig under mfd directory.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
88PM8606 and 88PM8607 are two discrete chips used for power management.
Hardware designer can use them together or only one of them according to
requirement.
There's some logic tightly linked between these two chips. For example, USB
charger driver needs to access both chips by I2C interface.
Now share one driver to these two devices. Only one I2C client is identified
in platform init data. If another chip is also used, user should mark it in
companion_addr field of platform init data. Then driver could create another
I2C client for the companion chip.
All I2C operations are accessed by 860x-i2c driver. In order to support both
I2C client address, the read/write API is changed in below.
reg_read(client, offset)
reg_write(client, offset, data)
The benefit is that client drivers only need one kind of read/write API. I2C
and MFD driver can be shared in both 8606 and 8607.
Since API is changed, update API in 8607 regulator driver.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Create 88pm8607-i2c driver to support all I2C operation of 88PM8607.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This converts the AB3100 core MFD driver to use a threaded
interrupt handler instead of the explicit top/bottom-half
construction with a workqueue. This saves some code and make it
more similar to other modern MFD drivers.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The headphone detect and charger are using the IRQ numbers so need
to take account of irq_base with the genirq conversion. I obviously
picked the wrong system for initial testing.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The genirq implementation does not allow modules to implement irq_chips
so the conversion of WM8350 to genirq means we can no longer allow the
driver to be built as a module.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This gives us use of the diagnostic facilities genirq provides and
will allow implementation of interrupt support for the WM8350 GPIOs.
Stub functions are provided to ease the transition of the individual
drivers, probably after additional work to pass the IRQ numbers via
the struct devices.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Unlike the wm8350-custom code genirq nests enable and disable calls
so we can't just unconditionally mask or unmask the interrupt,
we need to remember the state we set and only mask or unmask when
there is a real change.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: rtc-linux@googlegroups.com
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The structure t7l66xb should not be freed before the subsequent references
to its fields in the arguments to clk_put. Furthermore, this structure is
allocated near the beginning of the function, and a goto to the label
err_noirq appears after a successful allocation, so it would seem that the
kfree should be moved down below this label.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x,e;
identifier f;
iterator I;
statement S;
@@
*kfree(x);
... when != &x
when != x = e
when != I(x,...) S
*x->f
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Mark Brown