Patch from Lennert Buytenhek
On the enp2611, GPIO 7 and 6 are connected to an on-board i2c bus that
attaches to the SODIMM module slot (for SPD) and an LM84 temperature
sensor. Add a platform device for this i2c bus.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
This patch cleans up the ixp2000 gpio irq code and implements the
set_irq_type method for gpio irqs so that users can select for which
events (falling edge/rising edge/level low/level high) on the gpio
pin they want the corresponding gpio irq to be triggered.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Deepak Saxena
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
The IXP2000 has four timers, but if we're on an A-step IXP2800, timer
2 and 3 don't work. We need two timers for timekeeping (one for the
timer interrupt and one for tracking missed jiffies), so on early
IXP2800s we have no other choice but to use timer 1 and 4 for that,
but on all other IXP2000s we'd rather leave timer 4 free since that's
the only timer we can use for the watchdog.
So, on buggy IXP2000s (i.e. the A-step IXP2800) we use timer 4 for
tracking missed jiffies, and on all all non-buggy IXP2000s (i.e.
everything but the A-step IXP2800) we use timer 2.
On a pre-production IXP2800, this patch should print these messages
on boot:
Enabling IXP2800 erratum #25 workaround
Unable to use IXP2000 watchdog due to IXP2800 erratum #25
On any non-buggy IXP2800 (as well as on IXP2400s) you shouldn't see
anything at all, and the watchdog should be usable again.
Signed-off-by: Lennert Buytenhek
Signed-off-by: Deepak Saxena
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
The IXDP2800 is an evalution platform for the IXP2800 processor that
has two IXP2800s connected to the same PCI bus. This is problematic
as both CPUs will try to configure the PCI bus as they boot linux.
Contrary to on the other IXP2000 platforms, the boot loader on the
IXDP2800 doesn't configure the PCI bus properly, so we do want the
linux instance on one of the CPUs to do that.
Making one of the CPUs ignore the PCI bus (and thus act like a pure
PCI slave device) is not an option because there is a 82559 NIC on
the PCI bus for each of the CPUs.
The chosen solution is to have the master CPU configure the PCI bus
while the slave is kept in a quiescent state, and then to have the
slave CPU scan the PCI bus (without assigning resources) while the
master is kept in a quiescent state. After this ritual, the master
deletes the slave NIC from its PCI device list, the slave deletes
the master NIC from its device list, and (almost) all is well.
There's still one little problem: each of the CPUs has a 1G SDRAM
BAR, but the IXP2000 only has 512M of outbound PCI memory window.
We solve this by hand-assigning the master and slave SDRAM BARs to
a location outside each of the IXP's outbound PCI windows, and by
having the rest of the BARs autoconfigured in the outbound PCI
windows, in the range [e0000000..ffffffff], so that there is a 1:1
pci:phys mapping between them.
Even with this patch, a number of issues still remain -- just imagine
what happens if one of the CPUs is rebooted, by watchdog or by hand,
but the other one isn't. But those issues are not easily fixable
given the strange PCI layout of this board and the behavior of the
boot loader shipped with the platform.
Signed-off-by: Lennert Buytenhek
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
Assigning the address zero to a PCI device BAR causes some part of the
PCI subsystem to believe that resource allocation for that BAR failed
due to resource conflicts, which will make attempts to enable the
device fail. Work around this by assigning I/O addresses starting
from 00010000.
While we're at it, make the PCI I/O resource end at 0001ffff, since we
only have 64k of outbound I/O window on the IXP2000, and we don't do
bank switching.
Signed-off-by: Lennert Buytenhek
Signed-off-by: Deepak Saxena
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
On the IXDP2800, the bootloader does an awful job of configuring
the PCI bus, so we make linux reconfigure everything. Having a 1:1
pci:phys address mapping generally simplifies everything, so try to
allocate PCI addresses from the [e0000000..ffffffff] range, which is
the physical address range of the outbound PCI window on the IXP2000.
This does not affect any of the other IXP2000 platforms since they
all use their bootloader's PCI resource assignment.
Signed-off-by: Lennert Buytenhek
Signed-off-by: Deepak Saxena
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
Export ixp2000_pci_config_addr, to be used by the IXDP2800 platform
setup code to coordinate booting the master and slave NPU.
Signed-off-by: Lennert Buytenhek
Signed-off-by: Deepak Saxena
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Lennert Buytenhek