In ata_tf_to_lba48(), when evaluating
(tf->hob_lbal & 0xff) << 24
the expression is promoted to signed int (since int can hold all values
of u8). However, if hob_lbal is 128 or more, then it is treated as a
negative signed value and sign-extended when promoted to u64 to | into
sectors, which leads to the MSB 32 bits of section getting set
incorrectly.
For example, Phillip O'Donnell <phillip.odonnell@gmail.com> reported
that a 1.5GB drive caused:
ata3.00: HPA detected: current 2930277168, native 18446744072344861488
where 2930277168 == 0xAEA87B30 and 18446744072344861488 == 0xffffffffaea87b30
which shows the problem when hob_lbal is 0xae.
Fix this by adding a cast to u64, just as is used by for hob_lbah and
hob_lbam in the function.
Reported-by: Phillip O'Donnell <phillip.odonnell@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Remove excess kernel-doc function parameter notation from drivers/ata/:
Warning(drivers/ata/libata-core.c:1622): Excess function parameter or struct member 'fn' description in 'ata_pio_queue_task'
Warning(drivers/ata/libata-core.c:4655): Excess function parameter or struct member 'err_mask' description in 'ata_qc_complete'
Warning(drivers/ata/ata_piix.c:751): Excess function parameter or struct member 'udma' description in 'do_pata_set_dmamode'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Synchronize ahci_sw_activity and ahci_sw_activity_blink with ata_port lock.
Signed-off-by: David Milburn <dmilburn@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
I had assumed that the standard recovery would be sufficient for this
hardware but it isn't. Fix up the other registers on resume as needed. See
bug #11735
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
[http://lkml.org/lkml/2008/10/18/82]
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
libata EH saves xfer_mode and ncq_enabled at start to later set
DUBIOUS_XFER flag if it has changed. These values need to be cleared
on device detach such that hot device swap doesn't accidentally miss
DUBIOUS_XFER.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Due to request posting limitations, bandwidth of sil3132 is limited to
around 120MB/s with the minimum pci-e payload size (128bytes) which is
used by most consumer systems. However, write throughput can be
slightly (~3%) increased by increasing the max read requeset size.
Configure it to 4k which is the maximum supported. This optimization
is also done by SIMG's windows driver.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix libata missing kernel-doc:
Warning(lin2628-rc2//drivers/ata/libata-core.c:4562): No description
found for parameter 'tag'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There were several places where only enabled devices should be
iterated over but device enabledness wasn't checked.
* IDENTIFY data 40 wire check in cable_is_40wire()
* xfer_mode/ncq_enabled saving in ata_scsi_error()
* DUBIOUS_XFER handling in ata_set_mode()
While at it, reformat comments in cable_is_40wire().
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add an appropriate entry for the Promise PDC42819 controller. It has an
AHCI mode and so far works correctly with board_ahci.
This chip is found on Promise's FastTrak TX2650 (2 port) and TX4650 (4 port)
software-based RAID cards (for which there is a binary driver, t3sas) and
can be found on some motherboards, for example the MSI K9A2 Platinum,
which calls the chip a Promise T3 controller.
Although this controller also supports SAS devices, its default bootup mode
is AHCI and the binary driver has to do some magic to get the chip into the
appropriate mode to drive SAS disks.
Seeing as no documentation is provided by Promise, adding this entry to the
ahci driver allows the controller to be useful to people as a SATA
controller (with no ill effects on the system if a SAS disk is connected -
probing of the port just times out with "link online but device
misclassified"), without having to resort to using the binary driver. Users
who require SAS or the proprietary software raid can get this functionality
using the binary driver.
Signed-off-by: Mark Nelson <mdnelson8@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
For devices behind sata port multipliers, we have to make sure that
they share a tag map since all tags for that PMP must be unique.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The recent commit 2fca5ccf97 ("libata:
switch to using block layer tagging support") to enable support for
block layer tagging in libata was broken for non-NCQ devices
The block layer initializes the tag field to -1 to detect invalid uses
of a tag, and if the libata devices does NOT support NCQ, we just used
that field to index the internal command list. So we need to check for
-1 first and only use the tag field if it's valid.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Reported-by: Alexander Beregalov <a.beregalov@gmail.com>
Tested-by: Paul Mundt <lethal@linux-sh.org>
Tested-by: Dave Young <hidave.darkstar@gmail.com>
Tested-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
libata currently has a pretty dumb ATA_MAX_QUEUE loop for finding
a free tag to use. Instead of fixing that up, convert libata to
using block layer tagging - gets rid of code in libata, and is also
much faster.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
VIA controllers clear DEVICE register when IEN changes. Make sure
DEVICE is updated along with CTL.
This change is separated from Joseph Chan's larger patch.
http://thread.gmane.org/gmane.linux.kernel.commits.mm/40640
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Joseph Chan <JosephChan@via.com.tw>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Reset methods don't have access to phys link status for slave links
and may incorrectly indicate device presence causing unnecessary probe
failures for unoccupied links. This patch clears device class to NONE
during post-reset processing if phys link is offline.
As on/offlineness semantics is strictly defined and used in multiple
places by the core layer, this won't change behavior for drivers which
don't use slave links.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Slave link action mask is transferred to master link and all the EH
actions are taken by the master link. ata_eh_about_to_do() and
ata_eh_done() are called with ATA_EH_ALL_ACTIONS to clear the slave
link actions during transfer. This always sets ATA_PFLAG_RECOVERED
flag causing spurious "EH complete" messages.
Don't set ATA_PFLAG_RECOVERED for slave link actions.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ATA_EHI_NO_AUTOPSY and ATA_EHI_QUIET are used to control the behavior
of EH. As only the master link is visible outside EH, these flags are
set only for the master link although they should also apply to the
slave link, which causes spurious EH messages during probe and
suspend/resume.
This patch transfers those two flags to slave ehc.i before performing
slave autopsy and reporting.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ata_sff_post_internal_cmd() needs to grab port lock before calling
ata_bmdma_stop() and also need to clear hsm_task_state. Fix it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ap->port_task was not initialized if !CONFIG_ATA_SFF later triggering
lockdep warning. Make sure it's initialized.
Reported by Larry Finger.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
As of version 2.0, ACPI can return 64-bit integers. The current
acpi_evaluate_integer only supports 64-bit integers on 64-bit platforms.
Change the argument to take a pointer to an acpi_integer so we support
64-bit integers on all platforms.
lenb: replaced use of "acpi_integer" with "unsigned long long"
lenb: fixed bug in acpi_thermal_trips_update()
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
When no interrupt is specified the pata_of_platform fills the irq_res
resource with -1, which is wrong to do for two reasons:
1. By definition, 'no irq' should be IRQ 0, not some negative integer;
2. pata_platform checks for irq_res.start > 0, but since irq_res.start
is unsigned type, the check will be true for `-1'.
Reported-by: Steven A. Falco <sfalco@harris.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
SSD devices should give an RPM setting of 1 in word 217 of the ID
page. If we see such a device, tell the block layer about it.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Right now SCSI and others do their own command timeout handling.
Move those bits to the block layer.
Instead of having a timer per command, we try to be a bit more clever
and simply have one per-queue. This avoids the overhead of having to
tear down and setup a timer for each command, so it will result in a lot
less timer fiddling.
Signed-off-by: Mike Anderson <andmike@linux.vnet.ibm.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch updates the Intel Ibex Peak (PCH) IDE mode SATA Controller DeviceIDs.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Resets make ATAPI devices raise UNIT ATTENTION which fails the next
command. As resets can happen asynchronously for unrelated reasons,
this sometimes disrupts innocent users. For example, reading DVD
fails after the system wakes up from suspend or the other device
sharing the channel went through bus error.
Clearing UA has some problems as it might clear UA which the userland
needs to know about. However, UA after resets can only be about the
reset itself and benefits of clearing it overweights cons. Missing UA
can only delay failure to one of the following commands anyway. For
example, timeout while burning is in progress will trigger reset and
reset the device state and probably corrupt the burning run. Although
the userland application won't get the UA, its pending writes will
fail.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
[akpm@linux-foundation.org: remove ifdefs, make things static]
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Now that arch/ppc is dead CONFIG_PPC_MERGE is always defined for all
powerpc platforms and we want to get rid of CONFIG_PPC_MERGE use
CONFIG_PPC instead.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
On user request (through sysfs), the IDLE IMMEDIATE command with UNLOAD
FEATURE as specified in ATA-7 is issued to the device and processing of
the request queue is stopped thereafter until the specified timeout
expires or user space asks to resume normal operation. This is supposed
to prevent the heads of a hard drive from accidentally crashing onto the
platter when a heavy shock is anticipated (like a falling laptop
expected to hit the floor). In fact, the whole port stops processing
commands until the timeout has expired in order to avoid any resets due
to failed commands on another device.
Signed-off-by: Elias Oltmanns <eo@nebensachen.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The RPC machine type now selects HAVE_PATA_PLATFORM so we can remove
the special case in the PATA_PLATFORM configuration code.
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Now that libata has slave_link, there's no need to keep ugly merged
SCR access. Drop it and use slave_link instead. This results in
simpler code and much better separate link handling for master and
slave.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Explanation taken from the comment of ata_slave_link_init().
In libata, a port contains links and a link contains devices. There
is single host link but if a PMP is attached to it, there can be
multiple fan-out links. On SATA, there's usually a single device
connected to a link but PATA and SATA controllers emulating TF based
interface can have two - master and slave.
However, there are a few controllers which don't fit into this
abstraction too well - SATA controllers which emulate TF interface
with both master and slave devices but also have separate SCR
register sets for each device. These controllers need separate links
for physical link handling (e.g. onlineness, link speed) but should
be treated like a traditional M/S controller for everything else
(e.g. command issue, softreset).
slave_link is libata's way of handling this class of controllers
without impacting core layer too much. For anything other than
physical link handling, the default host link is used for both master
and slave. For physical link handling, separate @ap->slave_link is
used. All dirty details are implemented inside libata core layer.
From LLD's POV, the only difference is that prereset, hardreset and
postreset are called once more for the slave link, so the reset
sequence looks like the following.
prereset(M) -> prereset(S) -> hardreset(M) -> hardreset(S) ->
softreset(M) -> postreset(M) -> postreset(S)
Note that softreset is called only for the master. Softreset resets
both M/S by definition, so SRST on master should handle both (the
standard method will work just fine).
As slave_link excludes PMP support and only code paths which deal with
the attributes of physical link are affected, all the changes are
localized to libata.h, libata-core.c and libata-eh.c.
* ata_is_host_link() updated so that slave_link is considered as host
link too.
* iterator extended to iterate over the slave_link when using the
underbarred version.
* force param handling updated such that devno 16 is mapped to the
slave link/device.
* ata_link_on/offline() updated to return the combined result from
master and slave link. ata_phys_link_on/offline() are the direct
versions.
* EH autopsy and report are performed separately for master slave
links. Reset is udpated to implement the above described reset
sequence.
Except for reset update, most changes are minor, many of them just
modifying dev->link to ata_dev_phys_link(dev) or using phys online
test instead.
After this update, LLDs can take full advantage of per-dev SCR
registers by simply turning on slave link.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Implement __ata_port_next_link() and reimplement
__ata_port_for_each_link() and ata_port_for_each_link() using it.
This removes relatively large inlined code and makes iteration easier
to extend.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Logically, SCR access ops should take @link; however, there was no
compelling reason to convert all SCR access ops when adding @link
abstraction as there's one-to-one mapping between a port and a non-PMP
link. However, that assumption won't hold anymore with the scheduled
addition of slave link.
Make SCR access ops per-link.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit 2fd673ecf0 which tried to remove
hardreset for generic accidentally removed it for all flavors as all
others were inheriting from nv_generic_ops. This patch reinstates
nv_hardreset() and puts it into nv_common_ops which all flavors
inherit from. nv_generic_ops now inherits from nv_common_ops and
overrides .hardreset to ATA_OP_NULL.
While at it, explain why nv_hardreset and ATA_OP_NULL override are
necessary.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
dock's uevent reported itself, not ata. It might be difficult to find an
ata device just according to a dock. This patch introduces docking ops
for each device in a dock. when docking, dock driver can send device
specific uevent. This should help dock station too (not just bay)
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Acked-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
dock driver can handle ata(bay) hotplug now. dock driver already handles
_EJ0 and _STA, so remove them. Also libata doesn't need register
notification handler anymore.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Acked-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Enable LED blinking.
Signed-off-by: Bob Stewart <bob@evoria.net>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
drivers/ata/ata_piix.c:1502:7: warning: symbol 'rc' shadows an earlier one
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Remove duplicate call to pcim_enable_device in sil680_init_one.
Signed-off-by: David Milburn <dmilburn@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
On HSM_ST_ERR, ata_hsm_move() triggers WARN_ON() if AC_ERR_DEV or
AC_ERR_HSM is not set. PHY events may trigger HSM_ST_ERR with other
error codes and, with or without it, there just isn't much reason to
do WARN_ON() on it. Even if error code is not set there, core EH
logic won't have any problem dealing with the error condition.
OSDL bz#11065 reports this problem.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
of them being unifying probing, hotplug and EH reset paths uniform.
Previously, broken hardreset could go unnoticed as it wasn't used
during probing but when something goes wrong or after hotplug the
problem will surface and bite hard.
OSDL bug 11195 reports that sata_nv generic flavor falls into this
category. Hardreset itself succeeds but PHY stays offline after
hardreset. I tried longer debounce timing but the result was the
same.
http://bugzilla.kernel.org/show_bug.cgi?id=11195
So, it seems we'll have to drop hardreset from the generic flavor.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Peer Chen <pchen@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Marvell ahcis don't play nicely with PMPs. Disable it.
Reported by KueiHuan Chen in the following thread.
http://thread.gmane.org/gmane.linux.ide/33296
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: KueiHuan Chen <kueihuan.chen@gmail.com>
Cc: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
I've been chasing Jeff about this for months. Jeff added the Marvell
device identifiers to the ahci driver without making the AHCI driver
handle the PATA port. This means a lot of users can't use current
kernels and in most distro cases can't even install.
This has been going on since March 2008 for the 6121 Marvell, and late 2007
for the 6145!!!
This was all pointed out at the time and repeatedly ignored. Bugs assigned
to Jeff about this are ignored also.
To quote Jeff in email
> "Just switch the order of 'ahci' and 'pata_marvell' in
> /etc/modprobe.conf, then use Fedora's tools regenerate the initrd.
> See? It's not rocket science, and the current configuration can be
> easily made to work for Fedora users."
(Which isn't trivial, isn't end user, shouldn't be needed, and as it usually
breaks at install time is in fact impossible)
To quote Jeff in August 2007
> " mv-ahci-pata
> Marvell 6121/6141 PATA support. Needs fixing in the 'PATA controller
> command' area before it is usable, and can go upstream."
Only he add the ids anyway later and caused regressions, adding a further
id in March causing more regresions.
The actual fix for the moment is very simple. If the user has included
the pata_marvell driver let it drive the ports. If they've only selected
for SATA support give them the AHCI driver which will run the port a fraction
faster. Allow the user to control this decision via ahci.marvell_enable as
a module parameter so that distributions can ship 'it works' defaults and
smarter users (or config tools) can then flip it over it desired.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Roland Dreier