commit f9690982b8 removed the check for
cpu_khz from sched_clock(), which prevented early access to the TSC by
non obvious magic.
This is harmless as long as the CPU has a TSC. On TSCless systems this
results in an illegal instruction trap.
Replace tsc_disabled and tsc_unstable by tsc_enabled, which is only set
when the tsc is available and not unstable.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch resolves the issue found here:
http://bugme.osdl.org/show_bug.cgi?id=7426
The basic summary is:
Currently we register most of i386/x86_64 clocksources at module_init
time. Then we enable clocksource selection at late_initcall time. This
causes some problems for drivers that use gettimeofday for init
calibration routines (specifically the es1968 driver in this case),
where durring module_init, the only clocksource available is the low-res
jiffies clocksource. This may cause slight calibration errors, due to
the small sampling time used.
It should be noted that drivers that require fine grained time may not
function on architectures that do not have better then jiffies
resolution timekeeping (there are a few). However, this does not
discount the reasonable need for such fine-grained timekeeping at init
time.
Thus the solution here is to register clocksources earlier (ideally when
the hardware is being initialized), and then we enable clocksource
selection at fs_initcall (before device_initcall).
This patch should probably get some testing time in -mm, since
clocksource selection is one of the most important issues for correct
timekeeping, and I've only been able to test this on a few of my own
boxes.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In order to share the common code in tsc.c which does CPU Khz calibration, we
need to make an accurate value of CPU speed available to the tsc.c code. This
value loses a lot of precision in a VM because of the timing differences with
real hardware, but we need it to be as precise as possible so the guest can
make accurate time calculations with the cycle counters.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The custom_sched_clock hook is broken. The result from sched_clock needs to
be in nanoseconds, not in CPU cycles. The TSC is insufficient for this
purpose, because TSC is poorly defined in a virtual environment, and mostly
represents real world time instead of scheduled process time (which can be
interrupted without notice when a virtual machine is descheduled).
To make the scheduler consistent, we must expose a different nature of time,
that is scheduled time. So deprecate this custom_sched_clock hack and turn it
into a paravirt-op, as it should have been all along. This allows the tsc.c
code which converts cycles to nanoseconds to be shared by all paravirt-ops
backends.
It is unfortunate to add a new paravirt-op, but this is a very distinct
abstraction which is clearly different for all virtual machine
implementations, and it gets rid of an ugly indirect function which I
ashamedly admit I hacked in to try to get this to work earlier, and then even
got in the wrong units.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Geode can safely use the TSC for highres, since:
1) Does not support frequency scaling,
2) The TSC _does_ count when the CPU is halted. Furthermore, the Geode
supports a mode called "suspension on halt", where Suspend mode (which
interacts with the power management states) is entered. TSC counting
during suspend mode is controlled by bit 8 of the Bus Controller
Configuration Register #0 (thanks Tom!).
3) no SMP :)
Check if "RTSC counts during suspension" and remove the requirement for
verification, so the clocksource code can safely select it as an timesource
for the highres timers subsystem.
Signed-off-by: Marcelo Tosatti <marcelo@kvack.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The TSC needs to be verified against another clocksource. Instead of using
hardwired assumptions of available hardware, provide a generic verification
mechanism. The verification uses the best available clocksource and handles
the usability for high resolution timers / dynticks of the clocksource which
needs to be verified.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The clocksource code allows direct updates of the rating of a given
clocksource now. Change TSC unstable tracking to use this interface and
remove the update callback.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Using a flag filed allows to encode more than one information into a variable.
Preparatory patch for the generic clocksource verification.
[mingo@elte.hu: convert vmitime.c to the new clocksource flag]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
make the TSC synchronization code more robust, and unify it between x86_64 and
i386.
The biggest change is the removal of the 'fix up TSCs' code on x86_64 and
i386, in some rare cases it was /causing/ time-warps on SMP systems.
The new code only checks for TSC asynchronity - and if it can prove a
time-warp (if it can observe the TSC going backwards when going from one CPU
to another within a critical section), then the TSC clock-source is turned
off.
The TSC synchronization-checking code also got moved into a separate file.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Enqueue clocksources in rating order to make selection of the clocksource
easier. Also check the match with an user override at enqueue time.
Preparatory patch for the generic clocksource verification.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The delayed work code in arch/i386/kernel/tsc.c is an unused leftover of the
GTOD conversion. Remove it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Clean up sched_clock() on i686: it will use the TSC if available and falls
back to jiffies only if the user asked for it to be disabled via notsc or
the CPU calibration code didnt figure out the right cpu_khz.
This generally makes the scheduler timestamps more finegrained, on all
hardware. (the current scheduler is pretty resistant against asynchronous
sched_clock() values on different CPUs, it will allow at most up to a jiffy
of jitter.)
Also simplify sched_clock()'s check for TSC availability: propagate the
desire and ability to use the TSC into the tsc_disable flag, previously
this flag only indicated whether the notsc option was passed. This makes
the rare low-res sched_clock() codepath a single branch off a read-mostly
flag.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Andi Kleen <ak@suse.de>
VMI timer code. It works by taking over the local APIC clock when APIC is
configured, which requires a couple hooks into the APIC code. The backend
timer code could be commonized into the timer infrastructure, but there are
some pieces missing (stolen time, in particular), and the exact semantics of
when to do accounting for NO_IDLE need to be shared between different
hypervisors as well. So for now, VMI timer is a separate module.
[Adrian Bunk: cleanups]
Subject: VMI timer patches
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
o sched_clock() a non-init function is using init data tsc_disable. This
is flagged by MODPOST on i386 if CONFIG_RELOCATABLE=y
WARNING: vmlinux - Section mismatch: reference to .init.data:tsc_disable from .text between 'sched_clock' (at offset 0xc0109d58) and 'tsc_update_callback'
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Avoid possible PIT livelock issues seen on SMP systems (and reported by
Andi), by not allowing it as a clocksource on SMP boxes.
However, since the PIT may no longer be present, we have to properly handle
the cases where SMP systems have TSC skew and fall back from the TSC.
Since the PIT isn't there, it would "fall back" to the TSC again. So this
changes the jiffies rating to 1, and the TSC-bad rating value to 0.
Thus you will get the following behavior priority on i386 systems:
tsc [if present & stable]
hpet [if present]
cyclone [if present]
acpi_pm [if present]
pit [if UP]
jiffies
Rather then the current more complicated:
tsc [if present & stable]
hpet [if present]
cyclone [if present]
acpi_pm [if present]
pit [if cpus < 4]
tsc [if present & unstable]
jiffies
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
cyrix_identify() should be __init because transmeta_identify() is.
tsc_init() is only called from setup_arch() which is marked as __init.
These two section mismatches have been detected using running modpost on
a vmlinux image compiled with CONFIG_RELOCATABLE=y.
Signed-off-by: Magnus Damm <magnus@valinux.co.jp>
Signed-off-by: Andi Kleen <ak@suse.de>
Add a CLOCKSOURCE_MASK macro to simplify initializing the mask for a struct
clocksource, and use it to replace literal mask constants in the various
clocksource drivers.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Acked-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As suggested by Roman Zippel, change clocksource functions to use
clocksource_xyz rather then xyz_clocksource to avoid polluting the
namespace.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Implement the time sources for i386 (acpi_pm, cyclone, hpet, pit, and tsc).
With this patch, the conversion of the i386 arch to the generic timekeeping
code should be complete.
The patch should be fairly straight forward, only adding the new clocksources.
[hirofumi@mail.parknet.co.jp: acpi_pm cleanup]
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This converts the i386 arch to use the generic timeofday subsystem. It
enabled the GENERIC_TIME option, disables the timer_opts code and other arch
specific timekeeping code and reworks the delay code.
While this patch enables the generic timekeeping, please note that this patch
does not provide any i386 clocksource. Thus only the jiffies clocksource will
be available. To get full replacements for the code being disabled here, the
timeofday-clocks-i386 patch will needed.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As part of the i386 conversion to the generic timekeeping infrastructure, this
introduces a new tsc.c file. The code in this file replaces the TSC
initialization, management and access code currently in timer_tsc.c (which
will be removed) that we want to preserve.
The code also introduces the following functionality:
o tsc_khz: like cpu_khz but stores the TSC frequency on systems that do not
change TSC frequency w/ CPU frequency
o check/mark_tsc_unstable: accessor/modifier flag for TSC timekeeping
usability
o minor cleanups to calibration math.
This patch also includes a one line __cpuinitdata fix from Zwane Mwaikambo.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Thomas Gleixner