Note that the hardware schematics and documentations can be obtained
here: http://www.bugcommunity.com/wiki/index.php/BUGbase
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds a Kconfig option for the avic irq controller
and lets the SoCs that need it select this option.
Also, as we have two irq controllers for i.MX, irq.c is not
appropriate anymore, so rename it to avic.c
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This bases on a patch by Fabio Estevam who added the device before it
was allocated dynamically.
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
While adapting the #defines for this I noticed that the offset
used for USB HS on i.MX35 differs from the documented offset.
I kept the working offset and commented that the documentation
differs.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Compared to the static devices the dynamic have a DMA resource.
This should be save as it seems unused in the driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Currently there is no platform data used in the driver. In case this
changes NULL is passed unused to the soc specific functions.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
The mx35_3ds comes with 2 GiByte NAND flash. This adds the
corresponding platform device.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
This patch fixes the following Kconfig warning :
"arch/arm/mach-mx25/Kconfig:18:warning: choice value used outside its
choice group
Signed-off-by: Eric Bénard <eric@eukrea.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Because we add a 3ds debug board support in mxc level, we remove
those redundant codes from board level.
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This add USB Host capability. The Armadillo 500 board is supplied
with two USB Host connectors driven by the USB OTG and USB Host 2
ports, through two NXP isp 1504 transceivers.
Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Since the using of Bad Block Table is not constantly a good behave
I had made it configurable.
Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
otg_ulpi_create is defined in drivers/usb/otg/ulpi.c which depends on
CONFIG_USB_ULPI. So protect its usage by the same symbol. Moreover
mxc_ulpi_access_ops needs CONFIG_MXC_ULPI.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Valentin Longchamp <valentin.longchamp@epfl.ch>
Cc: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The "EET" variant of the pcm037 board has an OLED display, using a S6E63D6
display controller on the first SPI interface, using GPIO57 as a chip-select
for it. S6E63D6 is initialised in the boot-loader, so we only have to take care
of the LCD. EET also adds several buttons and LEDs on GPIOs. This patch adds a
"pcm037_variant=" kernel command line parameter to specify at boot-time which
board the kernel is running on, default is "pcm970", specify "eet" for the EET
board.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds basic support for INCO startec's LILLY-1131 iMX31 based
modules. The module needs a baseboard support to work which will be
added in the next patch.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Fabio Estevam