Things are breaking horribly with sysrq called in interrupt context. I want
to try to fix it, but probably this is simpler. To tell the truth, sysrq is
normally run in interrupt context, so there shouldn't be any problem.
There's also a warning from the fault handler because it's run in atomic
context (I have a patch for that, only I deferred it). This is why I'm doing
this.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The poster child for this patch is the third tuntap_user hunk. When an ioctl
fails, it properly closes the opened file descriptor and returns. However,
the close resets errno to 0, and the 'return errno' that follows returns 0
rather than the value that ioctl set. This caused the caller to believe that
the device open succeeded and had opened file descriptor 0, which caused no
end of interesting behavior.
The rest of this patch is a pass through the UML sources looking for places
where errno could be reset before being passed back out. A common culprit is
printk, which could call write, being called before errno is returned.
In some cases, where the code ends up being much smaller, I just deleted the
printk.
There was another case where a caller of run_helper looked at errno after a
failure, rather than the return value of run_helper, which was the errno value
that it wanted.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch implements a stack trace for a thread, not unlike sysrq-t does.
The advantage to this is that a break point can be placed on showreqs, so that
upon showing the stack, you jump immediately into the debugger. While sysrq-t
does the same thing, sysrq-t shows *all* threads stacks. It also doesn't work
right now. In the future, I thought it might be acceptable to make this show
all pids stacks, but perhaps leaving well enough alone and just using sysrq-t
would be okay. For now, upon receiving the stack command, UML switches
context to that thread, dumps its registers, and then switches context back to
the original thread. Since UML compacts all threads into one of 4 host
threads, this sort of mechanism could be expanded in the future to include
other debugging helpers that sysrq does not cover.
Note by jdike - The main benefit to this is that it brings an arbitrary thread
back into context, where it can be examined by gdb. The fact that it dumps it
stack is secondary. This provides the capability to examine a sleeping
thread, which has existed in tt mode, but not in skas mode until now.
Also, the other threads, that sysrq doesn't cover, can be gdb-ed directly
anyway.
Signed-off-by: Allan Graves<allan.graves@gmail.com>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Paolo 'Blaisorblade' Giarrusso