This patch changes w83627hf and w83627ehf drivers to reserve only ports
0x295-0x296, instead of full 0x290-0x297 range. While some other
sensors chips respond to all addresses in 0x290-0x297 range, Winbond
chips respond to 0x295-0x296 only (this behavior is implied by
documentation, and matches behavior observed on real systems). This is
not problem alone, as no BIOS was found to put something at these unused
addresses, and sensors chip itself provides nothing there as well.
But in addition to only respond to these two addresses, also BIOS
vendors report in their ACPI-PnP structures that there is some resource
at I/O address 0x295 of length 2. And when later this hwmon driver
attempts to request region with base 0x290/length 8, it fails as one
request_region cannot span more than one device.
Due to this we have to ask only for region this hardware really
occupies, otherwise driver cannot be loaded on systems with ACPI-PnP
enabled.
Signed-off-by: Petr Vandrovec <vandrove@vc.cvut.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Cleanup the ioctl debug message in i2c-dev. In particular, the minor
number is redundant now that the minor number and the adapter number
are kept in sync.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ixp4xx and ixp2000 i2c bus drivers omit to fill the required
i2c_adapter name field. Copy the device driver name field there.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It's not nice to put #ifdef in the middle of functions.
CC: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/i2c/busses/i2c-viapro.c | 6 ++----
1 file changed, 2 insertions(+), 4 deletions(-)
Improve the register dump used to debug the i2c-viapro driver. The
original dump was missing the HSTSTS register and the block data
buffer.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/i2c/busses/i2c-viapro.c | 38 ++++++++++++++++++++++++++++++--------
1 file changed, 30 insertions(+), 8 deletions(-)
By slightly shifting the interface between vt596_access and
vt596_transaction, we can save two I/O accesses per SMBus transaction.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/i2c/busses/i2c-viapro.c | 7 +++----
1 file changed, 3 insertions(+), 4 deletions(-)
Make it clearer which chips are supported by the i2c-viapro driver,
and which support I2C block transactions.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Documentation/i2c/busses/i2c-viapro | 12 ++++++------
drivers/i2c/busses/i2c-viapro.c | 22 +++++++++++++---------
2 files changed, 19 insertions(+), 15 deletions(-)
Cleanups to the i2c-viapro driver:
* Kill unused defines.
* Kill interrupt-related code, as the driver doesn't use interrupts.
* Fix broken comments (some copied from i2c-piix4.)
* Centralize the unsupported command error case in vt596_access.
That way we'll catch all unsupported commands, not only
I2C_SMBUS_PROC_CALL.
* Refactor some code.
* Convert some dev_dbg into dev_err. Errors better be reported even in
non-debug mode.
* Do not verify that the final reset succeeded. It'll be checked at
the beginning of the next transaction anyway.
* Use the driver name to reserve the I/O region.
* Do not print the contents of the SMBREV register, it reads 0 on all
chips I've seen so far.
* Some other minor fixes all over the place.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/i2c/busses/i2c-viapro.c | 122 +++++++++++++---------------------------
1 file changed, 41 insertions(+), 81 deletions(-)
Implement the I2C block transactions on VIA chips which support them:
VT82C686B, VT8233, VT8233A, VT8235 and VT8237R. This speeds up EEPROM
accesses by a factor 10 or so.
I would like to thank Antonino A. Daplas, Hinko Kocevar, Salah Coronya
and Andreas Henriksson for their help in testing this new feature.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Documentation/i2c/busses/i2c-viapro | 7 +++++-
drivers/i2c/busses/i2c-viapro.c | 39 +++++++++++++++++++++++++++++++++---
2 files changed, 42 insertions(+), 4 deletions(-)
Before I go on cleaning up and improving the i2c-viapro driver, let's
fix all the coding style issues: mostly trailing white space, and
spaces used where tabs should be.
Signed-off-by: Jean Delvare <khali@linux-fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Documentation/i2c/busses/i2c-viapro | 12 ++---
drivers/i2c/busses/i2c-viapro.c | 76 ++++++++++++++++++------------------
2 files changed, 43 insertions(+), 45 deletions(-)
Move the check for SMBUS_QUICK in i2c_probe() after the forced
addresses have been handled. This makes it possible for a driver to
leave the probed address lists empty, only providing forced addresses,
and get i2c_probe to work even if the bus doesn't support SMBUS_QUICK.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/i2c/i2c-core.c | 15 +++++++++++----
1 file changed, 11 insertions(+), 4 deletions(-)
Using s8 instead of u8 to store temperature register values saves a
few instructions on sysfs file read. The very same was done for
several other drivers a while ago (lm63, lm83, lm90...)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/hwmon/w83l785ts.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
Convert the w83l785ts driver to use dynamic sysfs callbacks. This is a
small driver so the benefit is thin, but still worth it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/hwmon/w83l785ts.c | 36 ++++++++++++++++++------------------
1 file changed, 18 insertions(+), 18 deletions(-)
Clean up name string usage in 12 i2c bus drivers:
* Use the i2c_adapter name for requesting the I/O region rather than
redefining a new string.
* Do not initialize the i2c_adapter name to "unset".
This should save a few data bytes here and there.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/i2c/busses/i2c-ali1535.c | 6 +++---
drivers/i2c/busses/i2c-ali1563.c | 6 ++++--
drivers/i2c/busses/i2c-ali15x3.c | 5 +++--
drivers/i2c/busses/i2c-amd756.c | 5 ++---
drivers/i2c/busses/i2c-amd8111.c | 4 +++-
drivers/i2c/busses/i2c-i801.c | 4 ++--
drivers/i2c/busses/i2c-nforce2.c | 4 ++--
drivers/i2c/busses/i2c-piix4.c | 4 ++--
drivers/i2c/busses/i2c-sis5595.c | 5 +++--
drivers/i2c/busses/i2c-sis630.c | 6 ++++--
drivers/i2c/busses/i2c-sis96x.c | 5 +++--
drivers/i2c/busses/i2c-via.c | 4 ++--
12 files changed, 33 insertions(+), 25 deletions(-)
Discard a common out-of-date comment in 5 hardware monitoring drivers.
The hardware monitoring chip drivers are no more setting sensor limits
at initialization time, for quite some time already.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/hwmon/lm78.c | 1 -
drivers/hwmon/via686a.c | 1 -
drivers/hwmon/w83627hf.c | 1 -
drivers/hwmon/w83781d.c | 1 -
drivers/hwmon/w83792d.c | 1 -
5 files changed, 5 deletions(-)
Do not enable the VIA VT82C686A/B integrated sensors by default, as
disabled sensors usually means that this feature is not used so the
values won't make any sense. This has been confusing many users in the
past:
http://www2.lm-sensors.nu/~lm78/readticket.cgi?ticket=1786http://www2.lm-sensors.nu/~lm78/readticket.cgi?ticket=1811http://www2.lm-sensors.nu/~lm78/readticket.cgi?ticket=2052
It is still possible to forcibly enable the sensors by using the
force_addr module parameter.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Documentation/hwmon/via686a | 17 +++++++++++++++--
drivers/hwmon/via686a.c | 18 +++++++++++-------
2 files changed, 26 insertions(+), 9 deletions(-)
We can save 0.5kB of data in the via686a driver.
From: Denis Vlasenko <vda@ilport.com.ua>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
hwmon: adm9240 update 2/2: convert to use dynamic sysfs accessors
This patch converts adm9240 to use Yani Ioannou's dynamic sysfs callbacks,
reducing driver memory footprint from 16312 to 14104 bytes on 2.6.14-rc1,
removing the old driver macro mess.
Run tested on Intel SE440BX-2 mobo.
Signed-off-by: Grant Coady <gcoady@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
hwmon: adm9240 update 1/2: cleanups:
o remove i2c read/write wrapper interface as it does nothing,
o change kmalloc + memset to kzalloc
Signed-off-by: Grant Coady <gcoady@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ipw2200 driver code in current GIT contains a kmalloc() followed by
a memset() without handling a possible memory allocation failure.
Signed-off-by: Panagiotis Issaris <panagiotis.issaris@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
1) Forgotten counter incrementation in sis900_rx() in case
it doesn't get memory for skb, that leads to whole interface failure.
Problem is accompanied with messages:
eth0: Memory squeeze,deferring packet.
eth0: NULL pointer encountered in Rx ring, skipping
2) If counter cur_rx overflows and there'll be temporary memory problems
buffer can't be recreated later, when memory IS available.
3) Limit the work in handler to prevent the endless packets processing
if new packets are generated faster then handled.
Signed-off-by: Konstantin Khorenko <khorenko@sw.ru>
Signed-off-by: Vasily Averin <vvs@sw.ru>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch replaces current PowerPC 4xx EMAC driver with
new, re-written from the scratch version. This patch is quite big
(~234K) because there is virtualy 0% of common code between old and
new version.
New driver uses NAPI, it solves stability problems under heavy packet
load and low memory, corrects chip register access and fixes numerous
small bugs I don't even remember now.
This patch has been tested on all supported in 2.6 PPC 4xx boards.
It's been used in production for almost a year now on custom
4xx hardware. PPC32 specific parts are already upstream.
Patch was acked by the current EMAC driver maintainer (Matt Porter). I
will be maintaining this new version.
Signed-off-by: Eugene Surovegin <ebs@ebshome.net>
--
Kconfig | 72
ibm_emac/Makefile | 13
ibm_emac/ibm_emac.h | 418 +++--
ibm_emac/ibm_emac_core.c | 3414 ++++++++++++++++++++++++----------------------
ibm_emac/ibm_emac_core.h | 313 ++--
ibm_emac/ibm_emac_debug.c | 377 ++---
ibm_emac/ibm_emac_debug.h | 63
ibm_emac/ibm_emac_mal.c | 674 +++++----
ibm_emac/ibm_emac_mal.h | 336 +++-
ibm_emac/ibm_emac_phy.c | 335 ++--
ibm_emac/ibm_emac_phy.h | 105 -
ibm_emac/ibm_emac_rgmii.c | 201 ++
ibm_emac/ibm_emac_rgmii.h | 68
ibm_emac/ibm_emac_tah.c | 111 +
ibm_emac/ibm_emac_tah.h | 96 -
ibm_emac/ibm_emac_zmii.c | 255 +++
ibm_emac/ibm_emac_zmii.h | 114 -
17 files changed, 4114 insertions(+), 2851 deletions(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Under heavy PCI bus load, ports of the DFE-580TX 4-ethernet port board stop
working, with currently no other cure than a powercycle. Here is a tested
fix. By the way, I also fixed some references and attribution.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Proper handling of suspend/resume in the wbsd driver.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
IXDP2x01 systems can be built without PCI network cards, so we should not
require NET_PCI to build CS89x0 on these systems.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
If the interface is not used right away after being probed it wastes
power needlessly. Noted by Holger Schurig.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Here is a patch that changes the way the MAC filter is computed for the
multicast addresses. The computation is taken from the SiS GPL driver.
This patch is necessary to get IPv6 working.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Looks like someone used the MII constants instead of the ethtool constants.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The documentation about s2io is available at
Documentation/networking/s2io.txt.
Signed-off-by: Akinobu Mita <mita@miraclelinux.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
prism54 is leaking information when passing transmits to the firmware.
There is no requirement to adjust the length to >= ETH_ZLEN.
Just pass the skb length (after possible adjustment).
Signed-off-by: Roger While <simrw@sim-basis.de>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Some older DL10019 based cards need to setup
the auto-negotiation-advertisement register
to advertise 100Full,100Half,10Full and 10Half.
Signed-off-by: <komurojun-mbn@nifty.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch fixes a bug that happens when the hypervisor can't add a
buffer. The old code wrote IBM_VETH_INVALID_MAP into the free_map
array, so next time the index was used, a ibmveth_assert() caught it and
called BUG(). The patch writes the right value into the free_map array
so that the index can be reused.
Signed-off-by: Santiago Leon <santil@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch adds the lockless TX feature to the ibmveth driver. The
hypervisor has its own locking so the only change that is necessary is
to protect the statistics counters.
Signed-off-by: Santiago Leon <santil@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch removes the allocation of RX skb's buffers from a workqueue
to be called directly at RX processing time. This change was suggested
by Dave Miller when the driver was starving the RX buffers and
deadlocking under heavy traffic:
> Allocating RX SKBs via tasklet is, IMHO, the worst way to
> do it. It is no surprise that there are starvation cases.
>
> If tasklets or work queues get delayed in any way, you lose,
> and it's very easy for a card to catch up with the driver RX'ing
> packets very fast, no matter how aggressive you make the
> replenishing. By the time you detect that you need to be
> "more aggressive" it is already too late.
> The only pseudo-reliable way is to allocate at RX processing time.
>
Signed-off-by: Santiago Leon <santil@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch changes the way the ibmveth driver handles the receive
buffers. The old code mallocs and maps all the buffers in the pools
regardless of MTU size and it also limits the number of buffer pools to
three. This patch makes the driver malloc and map the buffers necessary
to support the current MTU. It also changes the hardcoded names of the
buffer pool number, size, and elements to arrays to make it easier to
change (with the hope of making them runtime parameters in the future).
Signed-off-by: Santiago Leon <santil@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch updates dev->trans_start and dev->last_rx so that the ibmveth
driver can be used with the ARP monitor in the bonding driver.
Signed-off-by: Santiago Leon <santil@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Update version and reldate and add more sanity checking to
tg3_set_settings().
Signed-off-by: Gary Zambrano <zambrano@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Petr Vandrovec