On a POWER6 machine running 2.6.23-rc8 I sometimes see the following error:
xics_set_affinity: No online cpus in the mask 00000000,00000000,00000000,00000001 for irq 20
In a desperate attempt to get a changelog entry in 2.6.23, I took a look
into it.
It turns out we are passing a real and not a virtual irq into
get_irq_server. This works for the case where hwirq < NR_IRQS and we
set virq = hwirq. In my case however hwirq = 590082 and we try and
access irq_desc[590082], slightly past the end at 512 entries.
Lucky we ship lots of memory with our machines.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Setup dr_mode for USB-DR to peripheral as the default (host mode) doesn't make
much sense for the mini-AB connector on the ITX board.
Peripheral mode is preferable to OTG as the fsl_usb2_udc.c driver doesn't yet
properly support it.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
mpc834x USB-MPH configuration got broken by commit
6f44256002. The selection bits in SICRL
should be cleared rather than set to configure the USB MUXes for the MPH.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The powerpc version of commproc.c exports cpm_dpram_addr twice
and cpm_dpram_phys not at all due to a typo. This patch fixes this
problem.
CC arch/powerpc/sysdev/commproc.o
arch/powerpc/sysdev/commproc.c:398: error: redefinition of '__kcrctab_cpm_dpram_addr'
arch/powerpc/sysdev/commproc.c:392: error: previous definition of '__kcrctab_cpm_dpram_addr' was here
arch/powerpc/sysdev/commproc.c:398: error: redefinition of '__kstrtab_cpm_dpram_addr'
arch/powerpc/sysdev/commproc.c:392: error: previous definition of '__kstrtab_cpm_dpram_addr' was here
arch/powerpc/sysdev/commproc.c:398: error: redefinition of '__ksymtab_cpm_dpram_addr'
arch/powerpc/sysdev/commproc.c:392: error: previous definition of '__ksymtab_cpm_dpram_addr' was here
make[1]: *** [arch/powerpc/sysdev/commproc.o] Error 1
make: *** [arch/powerpc/sysdev] Error 2
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The commit 8b6f50ef1d seems to have
been affected by a mismerge of a duplicate patch
(d054b36ffd) - both the
spufs_dir_contents and spufs_dir_nosched_contents have been given
write-only signal notification files.
This change reverts the spufs_dir_contents array to use the
readable signal notification file implementation.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When PTRACE_O_TRACEEXEC is used, a ptrace call to fetch the registers at
the PTRACE_EVENT_EXEC stop (PTRACE_PEEKUSR) will oops in CHECK_FULL_REGS.
With recent versions, "gdb --args /bin/sh -c 'exec /bin/true'" and "run" at
the (gdb) prompt is sufficient to produce this. I also have written an
isolated test case, see https://bugzilla.redhat.com/show_bug.cgi?id=301791#c15.
This change fixes the problem by clearing the low bit of pt_regs.trap in
start_thread so that FULL_REGS is true again. This is correct since all of
the GPRs that "full" refers to are cleared in start_thread.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Recent changes to the timekeeping code broke support for the PowerPC 601
processor which doesn't have the usual timebase facility but a slightly
different thing called (yuck) the RTC.
This fixes it, boot tested on an old 601 based PowerMac 7200.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We forgot to remove the clock_gettime, clock_getres and get_tbfreq vDSO
calls on CPUs that have no timebase such as 601 or 403 (old CPUs that have
different mechanisms and for which the vDSO code will not work properly).
This fixes it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
find_victim can dereference a NULL pointer when iterating over the list
of victim spus because list_mutex only guarantees spu->ct to be stable,
but of course not to be non-NULL.
Also fix find_victim to not call spu_unbind_context without list_mutex
because that violates the above guarantee.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
With the I/O space rewrite by BenH, the legacy_serial serial_dev_init()
initcall is now called before I/O space is setup, but it's dependent on
it being available.
Since there's no way to make dependencies between initcalls, we'll just
have to move it to device_initcall(). Yes, it's suboptimal but I'm not
aware of any better solution at this time, and it fixes a regression
from 2.6.22.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since the ULI1575 has a ISA bus we need to enable the generic ISA dma
support for drivers that might expect it. Without this we get compile
errors like the following:
ound/built-in.o: In function `claim_dma_lock':
/home/galak/git/linux-8572/include/asm/dma.h:189: undefined reference to `dma_spin_lock'
/home/galak/git/linux-8572/include/asm/dma.h:189: undefined reference to `dma_spin_lock'
sound/built-in.o: In function `release_dma_lock':
/home/galak/git/linux-8572/include/asm/dma.h:195: undefined reference to `dma_spin_lock'
sound/built-in.o: In function `claim_dma_lock':
/home/galak/git/linux-8572/include/asm/dma.h:189: undefined reference to `dma_spin_lock'
/home/galak/git/linux-8572/include/asm/dma.h:189: undefined reference to `dma_spin_lock'
sound/built-in.o:/home/galak/git/linux-8572/include/asm/dma.h:195: more undefined references to `dma_spin_lock' follow
make: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The hardware adds one to the BRG value to get the divider, so it must
be subtracted by software. Without this patch, characters will occasionally
be corrupted.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Previously, ibmebus derived a device's bus_id from its location code.
The location code is not guaranteed to be unique, so we might get bus_id
collisions if two devices share the same location code. The OFDT
full_name, however, is unique, so we use that instead (truncating it
on the left if it is too long).
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On PS3, A storage device may show up in the repository before the hypervisor
has finished probing:
- If its type is not yet known, it shows up as PS3_DEV_TYPE_STOR_DUMMY,
- If its regions are being probed, it shows up as having zero regions.
If any of these happen, consider the device not yet present. The storage
probe thread will retry later.
This fixes the timing-dependent problem where a kernel booted from FLASH ROM
sometimes cannot find the hard disk.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
At present, running any SPE program on the ps3 will trigger a BUG_ON
when spufs_run_spu tries to clear the master run control bit, as lv1
does not make the master run control available to Linux.
This change makes SPE apps work again by disabling changes to the
master run control on PS3. Although we don't have the facility to
disable a SPE with supervisor-level privileges, it's better than
hitting the BUG_ON unconditionally.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Acked-by: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The Cell BE Architecture spec states that the SPU MFC Class 0 interrupt
is edge-triggered. The current spu interrupt handler assumes this
behavior and does not clear the interrupt status.
The PS3 hypervisor visualizes all SPU interrupts as level, and on return
from the interrupt handler the hypervisor will deliver a new virtual
interrupt for any unmasked interrupts which for which the status has not
been cleared. This fix clears the interrupt status in the interrupt
handler.
Signed-off-by: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix the bug that the major version part of the firmware version number
is ignored in the comparison done by ps3_compare_firmware_version
because the difference of two 64-bit quantities is returned as an int.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes a major bug which was happening when a SPU thread advances
its execution right after being restored to a SPU. A potentially
outdated NPC value was being (re)written to the SPU.
So, spu_run_init, in this case, was either not doing anything relevant,
or breaking the execution of the SPU thread.
This fixes a common problem of losing a mailbox write when it was done
to a saved context.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When a process writes into the inbound spu mailbox (wbox) while the
context is saved, we accidentally break the contents of the mb_stat_R
register by clearing other entries of the mailbox status register. This
can cause the user side to hang.
This change fixes the problem by only altering the appropriate bits
of the mailbox status register during a backing-store write.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes a regression introduced with 2.6.23-rc4 after on some
confusion about the device tree interfaces.
IBM QS21 device trees provide "physical-id", so we changed the code to
run on that and remain compatible with all IBM machines.
However, the Toshiba Celleb device tree provides the "unit-id" property,
which was in the Linux code, but never used in this way on IBM hardware.
Legacy device tree used the reg property for the physical id of an spe.
This patch fixes find_spu_unit_number to look for the spu id in that order.
The length is checked to avoid misinterpretation in case the attributes
unit-id or reg do not contain the id.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Cc: Jeremy Kerr <jk@ozlabs.org>
When we flush register state for FP, Altivec, or SPE in flush_*_to_thread
we need to respect the task_struct that the caller has passed to us.
Most cases we are called with current, however sometimes (ptrace) we may
be passed a different task_struct.
This showed up when using gdbserver debugging a simple program that used
floating point. When gdb tried to show the FP regs they all showed up as
0, because the child's FP registers were never properly flushed to memory.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This partially reverts edd0622bd2.
It turns out that the part of that commit that aimed to ensure that we
created an SLB entry for the kernel stack on secondary CPUs when
starting the CPU didn't achieve its aim, and in fact caused a
regression, because get_paca()->kstack is not initialized at the point
where slb_initialize is called.
This therefore just reverts that part of that commit, while keeping
the change to slb_flush_and_rebolt, which is correct and necessary.
Signed-off-by: Paul Mackerras <paulus@samba.org>
On exit do not delete gendisk's queue because this is already done by
del_gendisk(). Doing it twice may cause memory damage.
Signed-off-by: Maximilian <maxim@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Firmware would not deliver two interrupt numbers in device-tree any more
but only one, for correctable ECC, because uncorrectable ECC from now
is handled by firmware itself.
Changes in the axonram module are necessary because in the old version, if
it is not allowed to fetch the second interrupt number from device-tree,
it interpretes this as an error case and exits.
Signed-off-by: Maximilian <maxim@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The Cell Broadband Engine has a method of injecting a
system-reset-exception from an external source into the
operating system, which should trigger the regular behaviour
of entering xmon or kdump.
Unfortunately, the exception handler cannot distinguish it from
other interrupt causes by the SRR1 register, which gets used
for this on Power 6 and others.
IBM Blade servers that want to support triggering the
system reset exception using a pinhole button in the front
panel therefore use an extra register to determine the
reset cause.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
--
Signed-off-by: Paul Mackerras <paulus@samba.org>
Legacy device tree used the reg property for the physical id of an
spe. On newer device tree layouts the reg property contains the
"correct" value in the reg attribute. So there has been intoduced the
"physical-id" on newer devicetree layouts. The id is stored by
spu_manage into the spu struct as spe_id. cbe_thermal has been
changed to use the spu->spe_id. There's no need for the thermal code
to check devicetree attributes for itself.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Cc: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
More fallout from the switch from PAGE_SIZE based IOMMU to the native page
size for the driver. By pure luck it happened to work most of the time, since
we end up invalidating the wrong entries in the TLB.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The initial user manuals for MPC8544/8533 had some issues with properly
documenting the device IDs for MPC8544/8533. These processors are almost
identical and both show up on the reference boards.
Fix up the quirks for PCIe support to handle MPC8533/E.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
CC arch/powerpc/sysdev/commproc.o
arch/powerpc/sysdev/fsl_soc.c: In function fsl_pcmcia_of_init:
arch/powerpc/sysdev/fsl_soc.c:1109: error: implicit declaration of function of_platform_device_create
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Reserved MCSR bits on FSL BookE parts may have spurious values
when mcheck occurs. Mask these off when printing the MCSR to
avoid confusion. Also, get rid of the MCSR_GL_CI bit defined
for e500 - this bit doesn't actually have any meaning.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The interrupt routing in the device trees for the ULI M1575 was
inproperly using the interrupt line field as pci function. Fixed
up the device tree's to actual conform for to specification and
changed the interrupt mapping code so it just uses a static mapping
setup as follows:
PIRQA - IRQ9
PIRQB - IRQ10
PIRQC - IRQ11
PIRQD - IRQ12
USB 1.1 OCHI (1c.0) - IRQ12
USB 1.1 OCHI (1c.1) - IRQ9
USB 1.1 OCHI (1c.2) - IRQ10
USB 1.1 ECHI (1c.3) - IRQ11
LAN (1b.0) - IRQ6
AC97 (1d.0) - IRQ6
Modem (1d.1) - IRQ6
HD Audio (1d.2) - IRQ6
SATA (1f.1) - IRQ5
SMB (1e.1) - IRQ7
PMU (1e.2) - IRQ7
PATA (1f.0) - IRQ14/15
Took the oppurtunity to refactor the code into a single file so we
don't have to duplicate these fixes on the two current boards in the
tree and several forth coming boards that will also need the code.
Fixed RTC support that requires a dummy memory read on the P2P bridge
to unlock the RTC and setup the default of the RTC alarm registers to
match with a basic x86 style CMOS RTC.
Moved code that poked ISA registers to a FIXUP_FINAL quirk to ensure
the PCI IO space has been setup properly before we start poking ISA
registers at random locations.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The RTC CMOS driver expects the interrupt to be a resource of the platform
device. Use a fixed interrupt value of 8 since on PPC if we are using this
its off an i8259 which we ensure has interrupt numbers 0..15.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
A similar fix to netfilter from Eric Dumazet inspired me to
look around a bit by using some grep/sed stuff as looking for
this kind of bugs seemed easy to automate. This is one of them
I found where it looks like this semicolon is not valid.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix probing of PS3 storage devices: in the success case, we should set
`error' to zero, not `result'.
Without this patch no storage devices are found.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
ppc64 does the unusual thing of using #include on a compiler-generated
assembly file (lparmap.s) from an assembly source file (head_64.S).
This runs afoul of my recent patch to pass -gdwarf2 to the assembler
under CONFIG_DEBUG_INFO. This patch avoids the problem by disabling
DWARF generation (-g0) when producing lparmap.s.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The 440 family of processors don't have a tlbie instruction. So, we
implement TLB invalidates by explicitly searching the TLB with tlbsx.,
then clobbering the relevant entry, if any. Unfortunately the PID for
the search needs to be stored in the MMUCR register, which is also
used by the TLB miss handler. Interrupts were enabled in _tlbie(), so
an interrupt between loading the MMUCR and the tlbsx could cause
incorrect search results, and thus a failure to invalide TLB entries
which needed to be invalidated.
This fixes the problem in both arch/ppc and arch/powerpc by inhibiting
interrupts (even critical and debug interrupts) across the relevant
instructions.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
AFAICT, nobody is using ft_ordered(), and it causes a build warning
to be generated. This patch cleans that up by removing the function
and the commented-out code that calls it.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
At present, spu_create with an invalid neighbo(u)r will return -ENOSYS,
not -EBADF, but only when spufs.o is built as a module.
This change adds the appropriate errno, making the behaviour the same
as the built-in case.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
My "slices" address space management code that was added in the 2.6.22
implementation of get_unmapped_area() doesn't properly check that the
size is a multiple of the requested page size. This allows userland to
create VMAs that aren't a multiple of the huge page size with hugetlbfs
(since hugetlbfs entirely relies on get_unmapped_area() to do that
checking) which leads to a kernel BUG() when such areas are torn down.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
powerpc has a couple of bugs in the usage of dma_masks that tend to
break when drivers explicitly try to set a 32-bit mask for example.
First, the code that generates the pci devices from the OF device-tree
doesn't initialize the mask properly, then our implementation of
set_dma_mask() was trying to validate the -previous- mask value, not the
one passed in as an argument.
This fixes these problems.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This reverts commit 3baee95595.
That commit was a mistake from the start; I added mdio type to the
bus scan list early on in my ucc_geth migrate to phylib development,
which is just pure wrong (the ucc_geth_mii driver creates the mii
bus and the PHY layer handles PHY enumeration without translation).
This follows on from commit 77926826f301fbd8ed96d3cd9ff17a5b59560dfb:
Revert "[POWERPC] Don't complain if size-cells == 0 in prom_parse()"
which was basically trying to hide a symptom of the original mistake
this revert fixes.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove the Kconfig message that indicates the PS3 platform support is
incomplete.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix the PS3 storage probe logic to properly find device regions on cold
startup.
o Change the storage probe event mask from notify_device_ready
to notify_region_update.
o Improve the storage probe error handling.
o Change ps3_storage_wait_for_device() to use a temporary variable to hold
the buffer address.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch moves affinity initialization code from spu_base.c to a
new spu_management_of_ops function (init_affinity), which is empty
in the case of PS3. This fixes a linking problem that was happening
when compiling for PS3.
Also, some small code style changes were made.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Anton Blanchard